TigerTough W0521035 Bucket Seat Covers for Ford Trucks Instruction Manual

August 30, 2024
TigerTough

W0521035 Bucket Seat Covers for Ford Trucks

“`html

Specifications:

  • Part Number: W0521035
  • Product Type: Bucket Seat Covers
  • Pieces Included:
    • (1) Driver Back
    • (1) Driver Bottom
    • (1) Passenger Back
    • (1) Passenger Bottom
    • (2) Headrest Covers
    • (2) Stringlocks

Product Usage Instructions:

General Care Instructions:

  1. In most cases, dirt, debris, spills, and pet hair can be
    removed by wiping with a damp cloth.

  2. Seat covers can be removed and machine washed on a
    low-temperature setting using mild detergent. Straps should be
    coiled and secured with rubber bands for machine washing and
    drying.

  3. Soil may be removed with spray cleaner or detergent and
    water.

  4. Oil or grease stains should first be treated with a dry
    cleaning solvent followed by a spray cleaner or detergent and
    water.

  5. Do not use bleach.

Important Note on Airbag Compatibility:

Your seat covers are designed with a tearaway flap to allow seat
side airbags to deploy. Ensure the flap and the TigerTough tag are
facing the door to prevent any issues in the event of a crash.

Installation Instructions:

1 – Preparation:

  • Unhook from seat bottom.

  • Pull down to detach from seat bottom.

  • Slide seat forward and raise to the highest position, if
    possible.

  • Remove headrest by pressing in tabs at the base and pulling
    up.

  • Pull the yellow plug out of the bottom of the seat.

  • Unhook elastic straps from under the seat bottom.

2 – Install Seat Bottom Cover:

  1. Put cover over the seat bottom.

  2. Tuck the outside of the cover behind plastic trim and the
    inside between the seat bottom and center console.

  3. Tuck the outside string between the seat bottom and trim, while
    the inside string goes down and under the seat. Ensure strings run
    in front of rear seat mounts.

  4. Pull strings tight under the seat and secure using the
    StringLock device. The tighter, the better to prevent
    shifting.

  5. Push the top flap between the seat back and seat bottom,
    ensuring slits in cover line up with wires in the seat back.

  6. Run the front flap over seat adjustment levers, wires, and
    brackets. Pull it tight and fasten to Velcro on the top flap.

The StringLock:

  1. Run one string through the channel on the end of the
    StringLock.

  2. Pull the string tight, pulling the StringLock towards one edge
    of the seat. Press the string into the clamp to lock it in
    place.

FAQ:

Q: What should I do if I encounter issues during

installation?

A: If you face any difficulties or have questions during
installation, please contact us at 507.246.3545 or email
orders@tigertough.com for assistance.

“`

Hey there!
It’s not rocket science, but following the instructions will make installing your seat covers a lot easier. We promise.
If you have any questions, comments, or issues, we’re here to help! You can reach us at 507.246.3545 (call or text) or email orders@tigertough.com.
PART NUMBER W0521035 PRODUCT TYPE BUCKET SEAT COVERS
PIECES (1) DRIVER BACK (1) DRIVER BOTTOM (1) PASSENGER BACK (1) PASSENGER BOTTOM (2) HEADREST COVERS (2) STRINGLOCKS

Basically, you break it, we buy it. Seriously.
Your new seat covers are covered by a two-year, unconditional, no B.S. warranty.
That means that if you manage to abuse them to a point that they can’t perform like they’re supposed to within two years of when you bought them, we’ll make it right. Depending on what is more practical, we’ll either repair or replace the damaged cover.

General care instructions:
1. In most cases dirt, debris, spills and pet hair can be removed by wiping with a damp cloth.
2. Seat covers can be removed and machine washed on low temperature setting using mild detergent. Drip dry or machine tumble dry on a no heat cycle. Straps should be coiled and secured with rubber bands for machine washing and drying.
3. Soil may be removed with spray cleaner or detergent and water.
4. Oil or grease stains should first be treated with a dry cleaning solvent followed by a spray cleaner or detergent and water.
5. Do not use bleach.

IMPORTANT: AIRBAG COMPATABILITY
YOUR SEAT HAS SEAT SIDE AIRBAGS. For maximum safety in the event of a crash, these airbags MUST NOT be restricted.
Your cover has been engineered with a tearaway flap (stitched with white thread) that will allow the airbag to deploy. Ensure that this flap & the orange TigerTough tag are facing the door.
TigerTough is not responsable for any issues resulting from incorrectly installed seat covers.

1 – Preparation

Unhook from seat bottom.

Pull down to detatch from seat bottom.

q 1.1 – Slide seat forward and raise to highest position, if possible. q 1.2 – Remove headrest by pressing in tabs at base of headrest and pulling up q 1.3 – Pull yellow plug out of bottom of seat. q 1.4 – Unhook elastic straps from under seat bottom.

2 – Install Seat Bottom Cover
q 2.1 – Put cover over seat bottom. q 2.2 – Tuck outside of cover behind plastic trim. Tuck inside of cover between seat bottom and center console. q 2.3 – Tuck outside string between seat bottom and trim, where the back and bottom meet. Inside string goes down
and under seat. Strings must run in front of rear seat mounts. q 2.4 – Pull strings tight under the seat, and secure using the StringLock device (see next page). The tighter, the better.
This is what keeps your cover from shifting q 2.5 – Push top flap between seat back and seat bottom. Slits in cover line up with wires in seat back. q 2.6 – Run front flap over seat adjustment levers, wires, and brackets. q 2.7 – Pull front flap tight and fasten to Velcro on top flap.

THE STRINGLOCK
1Run one string through the channel on the end of the StringLock.
2Pull the string tight, pulling the StringLock towards one edge of the seat. Press the string into the clamp, locking it in place.
3Run the second string through the StringLock just like the other one.
4Pull the loose end of the second string until everthing is tight and lock it into place as well.
Watch the video ttcovers.com/stringlock

3 – Install Seat Back Cover
q 3.1 – Turn seat back cover 3/4 of the way inside out and pull over seat back. q 3.2 – Line holes in cover up with headrest holes and work holes around plastic trim. q 3.3 – Continue pulling the cover down over the seat, unrolling it as you go. q 3.4 – Push front flap between seat back and seat bottom. q 3.5 – Pull front flap tight and fasten to Velcro on seat back. q 3.6 – Long flap on rear of seat back fastens to Velcro on underside of seat bottom cover.

4 – Install Headrest Cover
q 4.1 – Put headrest back in seat by pressing plastic tabs and pushing down on headrest. q 4.2 – Pull cover over head rest with “loop” Velcro in front and “hook” Velcro in rear. q 4.3 – Fasten Velcro tabs together under headrest.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals