ELKO VVB1 Smart Water Heater Puck User Guide

August 28, 2024
ELKO

ELKO VVB1 Smart Water Heater Puck

Specifications

  • Product Name: ELKO Smart Water Heater Puck
  • Manufacturer: ELKO AS
  • Model: DUG_Water Heater Puck_ELKO-00
  • Website: www.elko.no

Product Information
The ELKO Smart Water Heater Puck is a smart device designed to work with the ELKO Smart system, allowing users to control their\ water heater remotely through the ELKO app.

About the device

The device enables users to monitor and adjust water heater settings from anywhere using the ELKO app, providing convenience and energy savings.

Installing the device

Follow the installation instructions provided in the user manual to securely attach the Water Heater Puck to your water heater unit.

Pairing the device

To pair the Water Heater Puck with your ELKO Smart system, follow the step-by- step instructions in the user manual or app. Make sure the device is within range of the system for successful pairing.

FAQs

Q: How do I reset the Water Heater Puck?
A: To reset the device, press and hold the reset button for 10 seconds until the LED indicator blinks rapidly. Release the button and wait for the device to restart.

Q: Can I schedule heating times with the ELKO Smart Water Heater Puck?
A: Yes, you can set heating schedules through the ELKO app to optimize energy usage and ensure hot water is available when needed.

Legal Information
The information provided in this document contains general descriptions, technical characteristics and/or recommendations related to products/solutions.
This document is not intended as a substitute for a detailed study or operational and site-specific development or schematic plan. It is not to be used for determining suitability or reliability of the products/solutions for specific user applications. It is the duty of any such user to perform or have any professional expert of its choice (integrator, specifier or the like) perform the appropriate and comprehensive risk analysis, evaluation and testing of the products/solutions with respect to the relevant specific application or use thereof.

The ELKO brand and any trademarks of ELKO AS and its subsidiaries referred to in this document are the property of ELKO AS or its subsidiaries. All other brands may be trademarks of their respective owner.
This document and its content are protected under applicable copyright laws and provided for informative use only. No part of this document may be reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of ELKO.
ELKO does not grant any right or license for commercial use of the document or its content, except for a non-exclusive and personal license to consult it on an “as is” basis.
ELKO reserves the right to make changes or updates with respect to or in the content of this document or the format thereof, at any time without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by ELKO and its subsidiaries for any errors or omissions in the informational content of this document, as well as any non-intended use or misuse of the content thereof.

Important Information
Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that accompany this symbol to avoid possible injury or death.

DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. Failure to follow these instructions will result in death or serious injury.

WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Operating elements
A. Status LED
B. Setup/Reset button

NOTICE
NOTICE is used to address practices not related to physical injury.

ELKO – Smart Water Heater Puck
ELKO – Smart Water Heater Puck

EKO20004
For your safety
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Safe electrical installation must be carried out only by skilled professionals. Skilled professionals must prove profound knowledge in the following areas: · Connecting to installation networks. · Connecting several electrical devices. · Laying electric cables. · Safety standards, local wiring rules and regulations. Failure to follow these instructions will result in death or serious injury.
DANGER
HAZARD OF ELECTRIC SHOCK Make sure that the terminal connection area does not come in contact with the metallic parts of any device installed in the same location. Failure to follow these instructions will result in death or serious injury.
WARNING
HAZARD OF ELECTRIC SHOCK · Observe the regulations for working on live parts. · Only actuate the device buttons using insulated auxiliary equipment that
meets the requirements of EN 60900. Failure to follow these instructions can result in death, serious injury, or equipment damage.

DUG_Water Heater Puck_ELKO-00

5

About the device

ELKO – Smart Water Heater Puck

The Smart Water Heater Puck (hereinafter referred to Water Heater/Puck) is intended for switching loads (up to 3000 W) such as a hot water tank or a socket outlet. In combination with the ELKO Smart app, the energy consumption can be measured and if necessary the load can be shed. Automatic module switch-off in case of load shedding or demand response request as well. Up to 10 modules can be added to the same system.

Operating elements: A. Status LED B. Setup/Reset button

Pairing device manually

Installing the device
Refer to the installation instruction supplied with this product. See Smart Water Heater Puck.
Pairing the device
Using the ELKO Smart app, pair your device with the ELKO SmartHub to access and control the device. You can either add the device manually or do an auto- scan to pair it.

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck
Pairing device manually
You can pair the each individual device to ELKO system manually with or without installed code.
1. On Home page, tap +.
2. Tap , select ELKO SmartHUB on the slide-up menu and tap Done. 3. Select any one of the options to add device (A):
­ Add Device with Install Code ­ Add Device without Install Code
Add Device

Install Code is Recommended
To enhance network security, we strongly recommend using the install code to add a
device. If you are unable to scan or type the install code, you can still add the device without it.

Add Device with Install Code

A

Add Device without Install Code

TIP: It is recommended to add the device with install code. 4. To pair the device with an install code, tap Add Device with Install Code to
display the slide-up menu. Select any one of the options (B): ­ Scan Install Code: you can scan the device for the install code. ­ Enter Install Code Manually: you can manually enter the install code
from the device. TIP: you can find the install code on the rear side of the device. After scanning or entering the install code, proceed to Step 7.
Add Device

Install Code is Recommended
To enhance network security, we strongly recommend using the install code to add a
device. If you are unable to scan or type the install code, you can still add the device without it.

Add Device with Install Code

Add DevSiccaenwIintshtoaulltCInodsetall Code

B

Enter Install Code Manually

Cancel

5. To pair the device without install code, tap Add Device without Install Code.

DUG_Water Heater Puck_ELKO-00

7

ELKO – Smart Water Heater Puck
6. Select any one of the options to add the device: ­ Short press the setup/reset button 3 times (<0,5 s) on the puck with a screwdriver. ­ Short press the push button 3 times.

The LED blinks Yellow. NOTE: If the puck is located behind the push button, the status LED is not visible.
7. In the app, select Confirm the indicator is blinking and tap Start Configuration (C).
Cancel
How to Pair Device
Using a screwdriver, Short-press the push button three times until the LED blinks yellow.

NL

kWh

C
After a few seconds, a solid green LED indicates that the device has been successfully paired to the ELKO SmartHUB.

8

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck 8. On successful pairing, assign a room and then tap Done.

Added successfully
Water Heater Device added successfully.

Energy Center Living Room

Kitchen

Bedroom

Bathroom

Done

9. On the configuration page, tap on the unconfigured device to start the configuration. NOTE: The energy monitoring feature is only enabled after the configuration has been completed.
10. Read the notification and then tap Confirm to open settings page.
11. On the setting page, tap (D) to select the configuration type from the slide-up menu.

Settings

Save

Identify

Type
Diagnosis
Signal Quality

Please select

D

Good

12. Select Water Heater from the list and then tap Confirm. TIP: You can also choose Custom and select the type according to your preference.

DUG_Water Heater Puck_ELKO-00

9

ELKO – Smart Water Heater Puck

13. Tap on (E) to rename the selection and then tap (F) to set the nominal power. NOTE: Nominal power is the maximum power the heater can manage. Setting this will enable you to use the energy optimization feature.

Settings

Save

Identify

Type Name
Related Power Settings
Nominal Power
Diagnosis
Signal Quality

Water Heater

Water Heater

E

?

2000 W

F

Good

14. After configuring, tap Save for pop-up notification. 15. Read the notification and then tap Confirm > OK 16. Once all Water heater are configured, tap Done.
Water heater will appear on the home screen along with new energy dashboard.

10

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck
Pairing device with auto scan
Pairing the device with auto scan automatically discovers the device when the corresponding device is powered on. Also helps yo to pair multiple devise at the same time.
1. On the Home page, tap + > Auto scan > Confirm. 2. Enable permissions to Access location and Wi-Fi for scanning device and
tap Start scanning. NOTE: If you have multiple hubs, do Step 3 or proceed to Step 4.
3. Tap Select hub and select the ELKO SmartHub from the slide-up menu. Wait for a few seconds until the device search is complete.
4. Tap Next (A) and select Water Heater.
Auto Scan
Available devices found

Water Heater

Next

A

5. Short press the Setup/Reset button or short press the push button 3 times (< 0,5 s) and wait for a few seconds until the device search is complete. The LED blinks yellow. TIP: If you want to pair multiple devices at once, perform step 5 on each device and wait for a few seconds for them to be detected.
6. On successful pairing, assign a room and then tap Done.

Added successfully
Water Heater Device added successfully.

Energy Center Living Room

Kitchen

Bedroom

Bathroom

Done

DUG_Water Heater Puck_ELKO-00

11

ELKO – Smart Water Heater Puck

7. On the configuration page, tap on the unconfigured device to start the configuration. NOTE: The energy monitoring feature is only enabled after the configuration has been completed.
8. Read the notification and then tap Confirm to open settings page.
9. On the setting page, tap (B) to select the configuration type from the slide-up menu.

Settings

Save

Identify

Type
Diagnosis
Signal Quality

Please select

B

Good

10. Select Water Heater from the list and then tap Confirm. TIP: You can also choose Custom and select the type according to your preference.
11. Tap on (C) to rename the selection and then tap (D) to set the nominal power. NOTE: Nominal power is the maximum power the heater can manage. Setting this will enable you to use the energy optimization feature.

Settings

Save

Identify

Type Name
Related Power Settings
Nominal Power
Diagnosis
Signal Quality

Water Heater

Water Heater

C

?

2000 W

D

Good

12. After configuring, tap Save for pop-up notification. 13. Read the notification and then tap Confirm > OK 14. Once all Water heater are configured, tap Done.
Water heater will appear on the home screen along with new energy dashboard.

12

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck
Configuring the device

Changing the device location

You can change the device location using the ELKO Smart app. 1. On the Home page, select the device for which you wish to change the location.

2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name. 4. Tap Location. 5. Select the desired location from the list (A) and then tap Save.

Device location

Save

Living Room Master Bedroom Kitchen
A
Dining Room Study Room Kids Room

DUG_Water Heater Puck_ELKO-00

13

ELKO – Smart Water Heater Puck

Managing device settings using ELKO Smart app

Using the ELKO Smart app, you can manage the Water heater settings.
To access the settings: 1. On the Home page, tap All devices > Water Heater. 2. On the device control panel page, tap Settings.

Settings

Save

Identify

A

Type Name
Related Power Settings
Nominal Power
Diagnosis
Signal Quality

Water Heater

Water Heater

B

?

2000 W

C

Good

Identifying the device
When you have multiple water heater, you can to identify a particular device to configure.
1. In Settings page, tap Identify (A). 2. Tap OK on the pop-up notification panel when the device is identified.
NOTE: The green LED on the identified device blinks for 30 s.
Renaming the device
You can rename the device according to your preference. 1. In Settings page, tap Name > (B). 2. Enter new name and then tap Save. NOTE: A device name cannot be entered as “Grid” or repeated. 3. In setting page, tap Save > OK to confirm the changes.
Setting nominal power
Nominal power is the maximum power the heater can manage. Setting this will enable you to use the energy optimization feature.
1. In Settings page, tap Nominal power > (C). 2. Enter power value based on the connected heating unit and then tap Save.
NOTE: The power value should range from 0 to 3000 W. 3. In setting page, tap Save > OK to confirm the changes.

14

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck

Managing tariff information

You can add tariff information in the ELKO Smart app to enable smart schedule. Refer Setting up a schedule, page 21.
NOTE: To access your energy cost and billing data, you must install SmartTag in your home.
To add tariff information:

1. Tap on the home page. 2. Select Home Management and select your home where the energy device is
installed, to view Home Settings. 3. On Home Settings page, select Tariff > Electricity.
You can view and update the following in electricity menu: A. Contract options, page 16 B. Tariff Zone, page 17 (Only available for spot price rate contract option) C. Subscription type, page 17 D. Rates, page (Not available for spot price rate contract option) E. Schedules, page 18 (Only available for time of use contract option)

Close

Electricity

Close

Electricity

No 1 Please Select

A
B Weekly – kr1
C Rates

Peak Rate

Rate 2 kr/kWh

D

Flat Rate

Rate 1 kr/kWh

Add a Rate

Save

Schedules

My Schedule Weekdays

00:00 – 00:00

E

Add A Schedule

Save

4. Once all the settings are updated, tap Save.

DUG_Water Heater Puck_ELKO-00

15

ELKO – Smart Water Heater Puck

Setting contract options

You can update flat and peak rate based on your contract option in the ELKO Smart app.
1. Tap My Contract Options on Electricity page.
2. In the slide-up menu, select any one of the following (A):
­ Time of Use (Peak/Off-Peak Hours): rate set to a specific period of time at which consumption is at its highest. It is the amount you pay for each unit of electricity consumed for the time period set.
­ Flat Rate: fixed rate for the entire time period of electricity consumption. ­ Spot Price Rate: standard hourly rate of electricity consumption as per
tariff zone. ­ No Contract: electricity rate is not set, no information related to bill will be
shown in the app.

Close

Electricity

Weekly – kr1
Rates
Peak Rate Rate 2 kr/kWh Flat Rate Rate 1 kr/kWh
Add a Rate

Schedules

My Schedule Weekdays

00:00 – 00:00

Flat Rate

A

Add A Schedule

Cancel

No Contract Save

NOTE: By default, No Contract option is set. 3. After selecting an option, tap Confirm.

16

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck

Tariff Zone

Once you select the spot price rate contract option, tariff zone option will be available. To select the tariff zone:
1. On Electricity page, tap Tariff Zone (A).
2. Select the zone based on your home location and tap Confirm.

Close

Electricity

No 1

A

Please Select

Save
NOTE: No 1 tariff zone is selected by default. Please modify if you live in other tariff zones. Click here to find your tariff zone.

Setting subscription type

Based on your electricity subscription, you can update subscription period and price in the ELKO Smart app.
1. Tap Subscription Type on Electricity page.
2. Select the subscription period (A). ­ Yearly ­ Monthly ­ Weekly ­ Daily
3. Enter Subscription Price (B), then tap Set.

Subscription types Yearly Monthly Weekly Daily

Set
A

1

B

DUG_Water Heater Puck_ELKO-00

17

Adding tariff rate

ELKO – Smart Water Heater Puck

You can add flat and peak rate value in the ELKO Smart app. 1. Tap Add a Rate on Electricity page. 2. Enter name and rate per kWh (A). 3. Tap Add (B).

Add Rate
Rate
Rate – kr/kWh

Set
A B

TIP: You can set the highest tariff rate as a peak rate and other tariff rates as an off-peak rate. Click here to find the tariff rates (maximum, minimum, average, peak and off-peak).

Adding schedule to tariff rate

You should add a scheduled time period for which a tariff rate will be active.

  1. Tap Add A Schedule on electricity page. 2. Enter a schedule Name (A). 3. Select the number of Days (B). 4. Tap Start Time and Finish Time to set the time period (C). 5. Tap Rate (D) and select the type of rate (Flat or Peak rate). 6. Tap Set to save the schedule.

Add Schedule
Name

Set
A

Days

Sun Mon Tue Wed Thu Fri Sat

B

Time
Start Time
C
Finish Time

Rate Type

Rate

D

18

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck
Using the device
The Control Panel of the Water heater allows you to view the current state of the device and allow you to access the history, schedule, and settings. On the Home page, tap All devices > Water Heater to access the control panel. On the control panel page, you can see the following:
· Instant Power (A) · Current state of the device and switch to turn on/off (B) · History, page 23 (C) · Schedule, page 21 (D) · Settings, page 14 (E)

Water Heater

Instant Power(kW)
2.51

A

B
On

History

C

Schedule

D

Settings

E

DUG_Water Heater Puck_ELKO-00

19

ELKO – Smart Water Heater Puck
Operating the device manually
When the Water heater is connected to a mechanical push button, the connected devices can be controlled manually by short pressing the push button.
NOTE: When the Water heater is installed inside the wall box, the status LED is not visible.

Operating the device using app
Using the ELKO Smart app, you can turn on/off the heater remotely. 1. On the Home page, tap All devices.

2. In Water Heater tap on (A) to turn on/off.

My Home Welcome Home
Set your home location for more information.

Home

Away

All Devices Living Room Master bedroom · · ·

Energy Dashboard Monthly consumption: 1.23 kWh

Water Heater 1.23 kW

A

Home

Automations

TIP: Alternatively, you can navigate to the control panel, page 19 of the device and then tap to turn on/off the heater.

20

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck

Setting up a schedule

The device can be fully controlled by schedule. Once the schedule is set, the device operates at a given time.
NOTE: When the gateway loses internet connectivity, the schedules will be suspended until the gateway’s internet connection is restored.
To access the schedule mode:
1. On the Home page, tap All devices > Water Heater. 2. On the device control panel page, tap Schedule.

Water Heater Schedule ?

Please select a schedule mode. This can be changed at any time.

Schedule Mode

No Schedule

A

Smart Control

B

Customized schedule

C

No Schedule Smart Control

You can select No Schedule (A) option if you don’t wish to run the heater according to a schedule and you can control your devices instantly whenever you like.
Selecting Smart Control (B), ELKO System will choosing when to switch your device ON based on the lowest electricity tariff. Prerequisite: To enable smart control, you must first add tariff. Refer tariff information, page 15.

DUG_Water Heater Puck_ELKO-00

21

ELKO – Smart Water Heater Puck

Customized schedule

You can create your own schedule to turn on/off the heater. Multiple schedules can be added based on your needs.
To add schedule: 1. In schedule mode, select Customized schedule (C) and then tap Add Schedule. 2. In Add Schedule menu, set the time (A). NOTE: The Schedule works according to the time zone where the device is located. 3. Tap Repeat (B) to select the days you want to set the schedule. 4. Tap Note (C), enter the note and tap Confirm. 5. Tap the toggle switch (D) to turn on the Notification for the schedule. The app will send a notification that the scheduled task is executed at the scheduled time. 6. Tap Switch (E) and select an option, On or Off.

Add Schedule

Save

08 06

09 07

A

10 08

Repeat Note

Once

B

C

D

Switch

On

E

Note – The schedule works according to the timezone where device is located.

7. Tap Save. TIP: If you have created a schedule for your device to be turned on for an hour at 6 PM, you will need to create one more schedule for it to be turned off at 7 PM.
To edit schedule: Tap on added schedule, edit details and tap Save. 1. In schedule list, tap on the one you want to edit.
2. Edit details and then tap Save. To delete schedule: In schedule list, press and hold the schedule for pop-up message and then tap Continue.

22

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck

Checking energy consumption

Using the ELKO Smart app, you can monitor the energy consumption by accessing the history.
1. On Home page, tap Energy Dashboard > History. or
In the Home page, tap All devices and select Water Heater > History.
2. On the History page, select a required time frame (A): ­ Hours: to view the hourly consumption. ­ Days: to view the daily consumption. ­ Months: to view the monthly consumption. ­ Years: to view the yearly consumption.

Energy

Live

History

Insights

Load consumption Months

A

From January 2023 Hours

Days

Jun

1.5

1.23 kWh Months

Years

0 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec
June
Water Heater 1.23 kWh

Breakdown
1.23 kWh Measured consumption in June
Water Heater

1.23 kWh

NOTE: Tap on the required hour/day/month/year in the bar graph to view the energy consumption for that time frame. 3. To view live data of the energy consumption., tap Live on energy dashboard.

Energy

Live

History

Insights

Today

00

03

06

09

12

15

18

21

kWh

14:00

00

03

06

09

12

15

18

21

NOTE: · Tap Show Live Price to view live price. · Drag on the graph to check the price for respective time period.

DUG_Water Heater Puck_ELKO-00

23

ELKO – Smart Water Heater Puck
Creating a moment
Moment allows you to group multiple actions that are usually done together. Using the ELKO Smart app, you can create moments based on your needs.
1. On the Home page, tap . 2. Go to Moment > + to create a moment.
3. Tap Edit name (A), enter the name of the moment and tap Save. TIP: You can choose the cover image that represents your moment by tapping .
Cancel Moment settings Save
Edit name

Action
A

Edit name Add Task

(0/10)

Cancel

Save

4. In the Action section, tap Add task (B) to open the slide-up menu. 5. In the Add task menu, you can do either or all of the following actions (C):
­ Run the device: select the devices that you want in a moment. ­ Select Automation: select the automation that you want to enable or
disable. ­ Delay: set the delay time.
NOTE: You can add one or more actions using .
Cancel Moment settings Save
Edit name

Action

(0/10)

Add Task

B

Add Task

Run the device

Select Automation

C

Delay

6. Tap Run the device > Water Heater.

24

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck 7. Tap on Switch and select either On / Off and then tap Save.
Select Function Next
Switch

Switch On

Cancel

Save

8. Tap Next and once the actions are set, tap Save.
Cancel Moment settings Save
Edit name

Action
Water Heater Switch:On

(Added1/80)

Show on Home Page

DUG_Water Heater Puck_ELKO-00

25

Editing a moment

ELKO – Smart Water Heater Puck
To edit a moment: 1. On the Moment tab, locate the moment you want to edit and tap . 2. On the Edit page, you can tap each item (such as dimmer, shutter, delay, temperature, etc.) to change the settings. TIP: · You can add one or more actions using . · To delete an existing action, slide the each item towards left and tap Delete.

Deleting a moment
To delete a moment: 1. On the Moment tab, locate the moment that you want to delete and then tap . 2. Tap Delete and then tap Ok. NOTE: After deleting a moment, the device action can no longer be triggered.

26

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck
Creating an automation
Automation allows you to group multiple actions that are usually done together, triggered automatically or at scheduled times. Using the ELKO Smart app, you can create automations based on your needs.
1. On the Home page, tap the . 2. Go to Automation > + to create an automation.
3. Tap Edit name (A), enter the name of the automation and tap Save. TIP: You can choose the cover image that represents your automation by tapping .
Cancel Automation settings Save
My Automation

Any condition is met Edit name

(0/10)

Add Condition
A

Action Cancel

(ASdadvede 0/80)

Add Task

All-Day

4. Tap Any condition is met to select any one of the condition type (B): ­ All conditions are met: the automation is triggered when all the conditions are met. ­ Any condition is met: the automation is triggered when at least one condition is met.
Cancel Automation settings Save
My Automation

Any condition is met

(0/10)

Add Condition

Action

(Added 0/80) Add Task

Select Condition type
All conditions are met
B
Any condition is met
Cancel

5. Tap Add Condition to open the slide-up menu.

DUG_Water Heater Puck_ELKO-00

27

ELKO – Smart Water Heater Puck
6. In the Add Condition menu, you can do either or all of the following options (C): ­ When weather changes: select various weather settings. ­ Schedule: set the time and day. ­ When device status changes: select the device and its function. ­ When Spot Price Changes: set the spot price and its condition.
NOTE: You can add one or more conditions using .
Cancel Automation settings Save
My Automation

Any condition is met

(0/10)

Add Condition

Add Condition

Schedule
C
When device status changes

7. Tap When device status changes > Water Heater and select either functions (D): ­ Instant Power: to set power limit. ­ Switch: turn off/on the switch. ­ Daily Consumption : to set the daily energy consumption. ­ Monthly Consumption: to set the monthly energy consumption.
Select Function
Instant Power Switch
D
Daily Consumption Monthly Consumption

28

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck

8. Tap When Spot Price Changes, set the required spot price and condition (lesser then/greater then).

Spot Price

Next

7

2

8

3

9

4

00

5

11

6

2

7

3

8

7

7

8

8

9

9

0

0 Kr/KWh

1

1

2

2

3

3

09:00

00

03

06

09

12

15

18

21 24

Example: If you set condition as Spot Price > 2 kr/kWh, your actions (defined in next step) will run when price goes above 2 kr/kWh. 9. Tap Add task to open the slide-up menu. 10. In the Add task menu, you can do either or all of the following options (E): ­ Run the device: select the devices that you want to trigger. ­ Moment or Automation: select the moment which you want to trigger or
select the automation that you want to enable or disable. ­ Send notification: turn on notification for the automation. ­ Delay: set the delay time.
NOTE: You can add one or more actions using .
Cancel Automation settings Save
My automation

Any condition is met

(0/10)

Add Condition

Action

(Added 0/80) Add Task

Run the deAvdidceTask

Moment or Automation

All-Day

E

Delay

DUG_Water Heater Puck_ELKO-00

29

ELKO – Smart Water Heater Puck

11. Tap on Effective period to set the time range for the automation. You can select any one of the following (F): ­ All-day – 24 hours ­ Daytime – From sunrise to sunset ­ Night – From sunset to sunrise ­ Custom – User defined time period

Next

All-day 24 hours

Daytime From sunrise to sunset

Night

F

From sunset to sunrise

Custom

Everyday

City

Please select a region

12. Once all the actions and conditions are set, tap Save. Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.
Example of an automation
This demonstration shows you how to create an automation to turn on the Water heater when the outdoor temperature is less than 18 °C .
1. Go to Automation > + to create an automation.
2. Tap to enter the name of automation and tap Save. TIP: You can choose the cover image that represents your automation by tapping .
3. Tap Add Condition > When weather changes > Outdoor Temperature.

30

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck

4. Select the outdoor temperature value (A), the condition (B) and tap Next. TIP: You can set the outdoor temperature value as 18 °C and the condition as < (less than).
Outdoor Temperature Next
City

B

0 7

+ 1 8C

A

-2 9

5. Tap Add task > Run the device and select Water Heater. 6. In select function page, tap Switch, select On (C) in the slide-up menu and
then tap Save > Next
Select Function Next
Switch

Switch

On

C

Cancel

Save

DUG_Water Heater Puck_ELKO-00

31

ELKO – Smart Water Heater Puck
7. In the Automation Settings page, tap Save.
Cancel Automation settings Save
My Automation

Any condition is met

(1/10)

Outdoor Temperature:<18 C

Action
Water Heater

(1/80) Switch: On All-Day

Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.
Editing an automation
To edit an automation: 1. On the Automation tab, locate the automation you want to edit and tap . 2. On the Edit page, you can tap each item (such as dimmer, shutter, delay, temperature, etc.) to change the settings. TIP: · You can add one or more actions using . · To delete an existing condition or action, slide each item towards left and tap Delete.
Deleting an automation
To delete an automation: 1. On the Automation tab, locate the automation that you want to delete and then tap . 2. Tap Delete and tap Ok. NOTE: After deleting an automation, the device action can no longer be triggered.

32

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck
Removing the device

Using the ELKO Smart app, you can remove a device from the device list. 1. On the Home page, tap All devices > Water Heater.

2. Tap to display more details. 3. Tap Remove and Factory Reset Device (A).

More

Water Heater Room: Living Room
Device information Moment and Automation
Others
FAQ & Feedback Add to home page
No updates available

Remove and Factory Reset Device

A

TIP: On the Home page, tap and hold the Water Heater to remove the device.
NOTE: · Removing the device will reset the Water heater.
· If there is a problem while pairing or resetting the Water heater, refer to Resetting the device manually, page 34.

DUG_Water Heater Puck_ELKO-00

33

Resetting the device

ELKO – Smart Water Heater Puck

You can reset the device to factory default manually.
1. Short press ( <0,5 s) the Setup/Reset button 3 times and then long press the Setup/Reset button once for 10 s to reset the Water heater to factory default mode. or Short press the push button 3 times a nd then long press the push button once for 10 s.
2. After 10 s, LED starts blinking red then release the Setup/Reset button.

NOTE: All configuration data, user data, and network data are deleted.
The LED stops blinking upon successful reset of the device. The Water heater restarts and blinks green for a few seconds.

34

DUG_Water Heater Puck_ELKO-00

ELKO – Smart Water Heater Puck
LED Indications
Pairing
User Action Press the Setup/Reset button 3 times

LED Indication Status LED blinks yellow, once per second.

Status
Pairing mode is active for 30 seconds. When pairing is completed, status LED glows green for some time before turning Off.

Resetting
User Action Press the Setup/Reset button 3 times and hold it for > 10 s.

LED Indication After 10 s, status LED starts blinking red.

Status
The device is in reset mode. It is reset to the factory settings after 10 seconds. The device then restarts and the status LED starts blinking green before turning Off.

Troubleshooting
Symptom The Water heater has gone offline.
Unable to join to the ELKO Smart HUB (blinking red LED)

Possible cause

Solution

· The Water heater is not On.
· The Water heater is no longer in signal range of the Hub.

· Turn the Water heater On and Off.
· Move the ELKO Smart HUB closer to the Water heater.

· Poor signal between the ELKO Smart HUB and Water heater.
· The devices have no power (Water heater / ELKO Smart HUB/ Wi-Fi® network).

· Rejoin the Water heater in the app.
· Turn on the devices power (Water heater/ELKO Smart HUB/ Wi-Fi® network).

DUG_Water Heater Puck_ELKO-00

35

Technical data
Nominal power rating for load type
R
L
Power supply Switching capabilities Power consumption Max. Power Operation Ambient temperature Connecting terminals Protection rating Communication protocol Radio frequency range Max. radio-frequency power transmitted Dimensions (W x L x H)

ELKO – Smart Water Heater Puck

LED Incandescent lamp

200 W 2200 W

Iron core transformer

500 VA

Motor
Resistive load Eg. Water tank or other electrical heater.
Capacitive load

1180 VA 3000 W 10 A, 25 µF

Inductive load

5 A, cos = 0.6

230 V AC, 50 Hz 230 V AC, 14 A <1W 3000 W, Integrated Zero crossing -20 ºC to 35 ºC Screw terminals: 1x 1 – 2.5 mm² IP20 Zigbee 3.0 (certified) 2.4 GHz < 10 mW 40 x 44 x 16.9 mm

36

DUG_Water Heater Puck_ELKO-00

EU Declaration of Conformity
Hereby, ELKO, declares that this product is in compliance with the essential requirements and other relevant provisions of RADIO EQUIPMENT DIRECTIVE 2014/53/EU. Declaration of conformity can be downloaded on ELKO.no.
Trademarks
This guide makes reference to system and brand names that are trademarks of their relevant owners.
· Zigbee® is a registered trademark of the Connectivity Standards Alliance. · Apple® and App Store® are brand names or registered trademarks of Apple Inc. · Google PlayTM Store and AndroidTM are brand names or registered trademarks
of Google Inc. · Wi-Fi® is a registered trademark of Wi-Fi Alliance®. Other brands and registered trademarks are the property of their respective owners.

ELKO AS Sandstuveien 68, 0680 Oslo Pb 6598 Etterstad, 0607 Oslo Norway
+47 67 79 39 00 support@elko.no www.elko.no
As standards, specifications, and design change from time to time, please ask for confirmation of the information given in this publication.
© 2023 ­ 2023 ELKO AS. All rights reserved. DUG_Water Heater Puck_ELKO-00

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals