ErGear EGESD55 Electric Standing Desk Frame Instruction Manual
- August 20, 2024
- ERGEAR
Table of Contents
ErGear EGESD55 Electric Standing Desk Frame
Specifications
- Height Adjustment Range: 28.3″-47.2″ (72-120cm)
- Power Input: 100V-240V
- Max. Speed: 25mm/s
- Operating Noise: ≤o55d8
- Max. Load: 265 lbs / 120 kg
Recommended Desktop Sizes
Tools Needed
Tools Needed (Not Included)
Supplied Parts and Hardware
Step 1
Step2
Step3
Step4
Not all hardware included in this package will be used.
Contact Us
If you receive parts that are damaged, defective, or are missing parts, please contact us.
- l-800-651-9525 (us/CA) Mon-Fri, 8 am-8 pm (CST)
- 44-808-196-3875 (UK) Mon-Fri, 2 pm-10 pm (UTC)
- support@ergear.com
Assembling the Leg Sections
Step 1
- Attach the crossbars to the desk legs.
- Attach the side plates to the desk legs.
- Attach the rubber pads to the leg sections.
- Place one leg section on the desktop, then insert the connecting bars into the crossbar end of the leg section. Slide the other leg section onto the connecting bars.
- Adjust the frame’s length according to the size of the desktop.
- Verify the connecting bars are positioned under the screw holes on the crossbar ends. If not, adjust by sliding the connecting bars.
- Secure the frame.
- Secure the frame to the desktop.
TIP
Ensure all bolts or screws are fully tightened.
Step2 Attaching Other Parts to the Desktop
- Fold the cable management tray along the dashed line, then attach it to the desired position.
WARNING
Be careful not to cut your fingers.
- Attach the storage hooks and controller to the desired position.
Step 3 Attaching the Leg Bases
Step4 Connecting the Cables
Note: An example of a cable clip layout is indicated below. However, the
cable clips can be arranged according to your needs.
- When flipping the desk over, do not allow the controller to collide with the ground, which could cause damage.
Using the Controller
TIP
- Reset before first use.
- Press any button to wake the screen before operating the desk.
Note: Ensure there are no obstacles when using the desk, that the desktop is not too close to the wall, and that all cables are long enough for the desk to move up and down freely.
-
Save Current Height Setting
Four heights can be saved. Press and hold the [I], [II, [ID, or I!) button for 5 seconds until is displayed. The current height will be saved to that button. -
Select Height Setting 1
Press the button. The desk will move to the height that was previously set for that button.
Select Height Setting 2 -
Press the button. The desk will move to the height that was previously set for that button.
Select Height Setting 3 -
Press the button. The desk will move to the height that was previously set for that button.
Select Height Setting 4 -
Press the button. The desk will move to the height that was previously set for that button.
Raise the Desk -
Press the button to raise the desk continuously until it reaches the highest position of 47.2″ (120cm) or the button is released.
Lower the Desk -
Press the button to lower the desk continuously until it reaches the lowest position of 28.3″ (72cm) or the button is released.
CONTACT
Thank you for choosing this ErGear product. At ErGear, we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us.
- 1-800-651-9525 (US/CA)
- 44-808-196-3875 (UK)
- Mon-Fri, 8am-8pm (CST)
- Mon-Fri, 2 pm-10 pm (UTC)
- support@ergear.com
- https://ergear.com
- 860-02580-00 Rev01
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>