ErGear EGESD5B 48 Height Adjustable Electric Standing Desk Instruction Manual

June 13, 2024
ERGEAR

ErGear-LOGO

ErGear EGESD5B 48 Height Adjustable Electric Standing Desk

ErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-
PRODUCT

PRODUCT INFORMATION

MODEL NAME:  Electric Standing Desk

PRODUCT INSTRUCTIONS

ErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG-
\(1\)

Technical Support:
(us/CA) l-800-651-9525 Mon-Fri, 8am-8pm (CST) (UK) 44-808-196-3875 Mon-Fri, 2pm-l0pm (UTC) Other Info : support@ergear.com Website : https://ergear.com

Specifications

Height Adjustment Range 28.3″-46.5″ (72-118cm)

Supplied Parts and Hardware

  1. Step 1 ErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(3\)
  2. Step 2 ErGear
  3. Step 3ErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(5\)
  4. Step 4ErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(6\)
  5. Step 5ErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(7\)

INSTALLATION

  1. Step 1 Assembling and Connecting the Desk Legs ErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(8\)
    • HEAVY! You may need assistance with this stepErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(9\)
  2. Step 2 Assembling and Connecting the Desk Legs EGESD5B
    • Loosen the coupling nut. ErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(12\)
    • Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the left leg. Turn the rod to adjust the left leg so it’s level with the right leg. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it.ErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(13\)
    • Ensure the transmission rod is properly inserted into the hole in the left leg. Smoothly connect the other end of the rod to the end of the motor drive shaft on the right leg. ErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(14\)
    • Secure the transmission rod to the motor drive shaft by turning the set screw clockwise . ErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(15\)
  3. STEP 3 Assembling and Connecting the Desk Legs
    • Assemble the desktop. ErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(16\)
    • Attach the desktop to the frame.ErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(17\)
    • Attach the controller and hooks to the desktop.ErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(18\)
  4. Step 4 Connecting the CablesErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(19\)
  5. Step 5 Installing the Cable Hole CoversErGear-EGESD5B-48-Height-Adjustable-Electric-Standing-Desk-FIG- \(20\)

Using the Controller

  • Save Current Height Setting
    Short-press the button, and the display will flash. Press the 00, ?, or [ID button to save the current height setting to that button.

  • Select Height Setting 1
    Press the  1 button, and the desk will move to the height that was previously set for that button.

  • Select Height Setting 2
    Press the  2 button, and the desk will move to the height that was previously set for that button.

  • Select Height Setting 3
    Press the 3 button, and the desk will move to the height that was previously set for that button.

  • Raise the Desk
    Press the button to raise the desk continuously until it reaches the highest position of 46.5″ (118cm) or the button is released.

  • Lower the Desk
    Press the button to lower the desk continuously until it reaches the lowest position of 28.3″ (72cm) or the button is released.

TROUBLESHOOTING

SETTINGS

Change Display Height Unit

| Press and hold thebutton until a flashing ‘S-‘ is displayed. Press again, and ‘Un’ is displayed. Press to select it, press  or  to switch between ‘IN’ (imperial)  and  ‘SI’ (metric), and press 00 to save your choice.

Change Collision Detection Sensitivity

| Press and hold the button until a flashing ‘S-‘ is displayed. Press again, and ‘Un’ is displayed. Press or to switch to ‘CF’ and press to  select it. Press or  to switch

between off, low, normal, and high sensitivity. Press 00 to save your choice.

Reset

| Press and  hold the   button for 5 seconds, and the  screen will show ‘RES.’ Continue holding until the desk goes  down to its lowest level and comes back up slightly.
SETTINGS

Hot

|

Overheating Protection: When the motor has been working continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least l8 minutes before making any further height adjustment.

ElO

|

Sensor Malfunction Warning: Motor safety sensor can’t be detected. Power off, check the connection between the motor and controller, and power back on again.

E20

|

Overloading Warning: Max load exc eed ed . If raising the desk, take the things off the desk and try again. If lowering the desk, power off, take the things off the desk, power back on, and try again.

E02

|

Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.

E32

|

Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and  power on again.

---|---

E31

|

Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and  the controller, and  power on again.

E60

|

Unequal Leg Height Warning: Power off the desk and check whether the left and right legs are at the same height. Adjust if necessary by following the instructions. Power on again.

 |

Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.

Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.

Technical Support:
( US/CA ) 1-800-651-9525 Mon- Fri, 8am-8pm (CST)
( UK ) 44-808-196-3875 Mon-Fri, 2pm-10pm (UTC)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals