ErGear EGESD6B-1 Electric Standing Desk with Double Drawers Instruction Manual

55″ Electric Standing Desk
Instruction Manual
Rev00(A)
(EcESDEB-1/ EGESDEV-1

EGESD6B-1 Electric Standing Desk with Double Drawers

Technical Support:
(Us/cA) 1-800-651-9525
Mon~—Fri, 8am—-8pm (CST)
(UK) 44-808-196-3875 Mon—Fri, 2pm-10pm (UTC)
Other Info: support@ergear.com
Website: https://ergear.com

Specifications

Height Adjustment Range
28.3″-46.5″ (72-118cm) Step 1
Supplied Parts and Hardware Step 2
Supplied Parts and Hardware Step 3
Supplied Parts and Hardware   Step 4
Supplied Parts and Hardware Step 5
Supplied Parts and Hardware Step 6
Supplied Parts and Hardware

Step 1 Assembling and Connecting the Desk Legs

Step 2 Attaching the Side Plates and the Transmission Rod

Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmis- sion rod into the hole in the left leg. Turn the rod to adjust the left leg so it’s level with the right leg. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it. Ensure the transmission rod is properly inserted into the hole in the left leg. Smoothly connect the other end of the rod to the end of the motor drive shaft on the right leg. Secure the transmission rod to the motor drive shaft by turning the set screw clockwise. Tighten the coupling nut to fine-tune transmission rod fit.

Step 3 Assembling and Attaching the Desktop

Assemble the desktop. Secure the desktop panels with the connectors. Attach the frame and hooks to the desktop.

Step 5 Giues Assembling and Attaching the Drawers

Screw the cam bolts into the top panels of the drawers.
Assemble the back panels and side panels of drawers.
Attach the top panels of the drawers.
Secure the drawer top panels with the cam locks and screws. Then cover the cam locks with the caps.
Attach the drawers to the desktop.Screw the cam bolts into the stand top panel. Attach and secure the stand top panel with cam locks and wood dowel pins. Then cover the cam locks with the caps. Unfold the fabric drawer.Place the board on the bottom of the fabric drawer. Attach the drawer knob to the drawer.
Attach the shelf pins.
Insert the shelf and fabric drawers.

Step 5 Attaching the Controller

Step 6 Connecting The Cables

Using the Controller

• Save Current Height Setting
  Short-press the  button, and the display will flash. Press the  ,  , or button to save the current height setting to that button.

• Select Height Setting 1
  Press the button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 2
  Press the   button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 3
  Press the  button, and the desk will move to the height that was previously set for that button.

• Raise the Desk
  Press the  button to raise the desk continuously until it reaches the highest position of 46.5” (118cm) or the button is released.

• Lower the Desk
  Press the  button to lower the desk continuously until it reaches the lowest position of 28.3″ (72cm) or the button is released.

Settings

Change Display Height Units| Press and hold the   button until a flashing ‘S- is displayed.
Press   again, and ‘Un’ is displayed. Press   to select it, press   or   to switch between ‘IN’ (imperial) and ‘Sl (metric), and press  to save your choice.
---|---
Change Collision Force Detection| Press and hold the   button until a flashing ‘S-” is displayed.
Press  again, and ‘Un’ is displayed. Press   or   to switch to ‘CF and press to select it. Press   or   to switch between OFF, Low (L), Normal (n), and Heavy (H) collision force detection. Press   to save your choice.
Reset| Press and hold the  button for 5 seconds, and the screen will show ‘RES.” Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

Hot| Overheating Protection: When the motor has been working continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least 18 minutes before making any further height adjustment.
---|---
E10| Sensor Malfunction Warning: Motor safety sensor can’t be detected. Power off, check the connection between the motor and controller, and power back on again.
E20| Overloading Warning: Max load exceeded. If raising the desk, take the things off the desk and try again. If lowering the desk, power off, take the things off the desk, power back on, and try again.
E02| Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.
E32| Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E31| Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E60| Unequal Leg Height Warning: Power off the desk and check whether the left and right legs are at the same height. Adjust if necessary by following the instructions. Power on again.
–| Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.

Complete Flexibility. Total Freedom.

Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.

Technical Support
(us/cA) 1-800-651-9525
Mon~—Fri, 8am—8pm (CST)
(UK) 44-808-196-3875
Mon—Fri, 2pm-10pm (UTC)
Other Infosupport@ergear.com
Websitehttps://ergear.com
860-00405-04 Rev00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>