ErGear Monitor Desk Mount EGDS6 Instruction Manual
- June 7, 2024
- ERGEAR
Table of Contents
- IMPORTANT SAFETY INFORMATION
- Product Features
- TENSION ADJUSTMENT SHOULD BE DONE ONLY AFTER MOUNT INSTALLATION
- Supplied Parts and Hardware
- Install the Base
- Install the Arms
- Step 3 Attach Monitors to the Arms
- Adjust Gas Spring Tension
- Rotation Restriction
- Tilt Adjustment
- Rotation Adjustment
- Route Cables along the Arms
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ErGear Monitor Desk Mount EGDS6 Instruction Manual
Thank you for choosing this Ergear product! At Ergear we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact at support@ergear.com (US/CA/DE/UK/FR/IT/ES/AU)
IMPORTANT SAFETY INFORMATION
Please carefully read all instructions before attempting installation. If you
do not understand the instructions or have any concerns or questions, please
contact our customer service at
support@ergear.com.
CAUTION: Avoid potential personal injuries and property damage!
-
Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use. -
This product contains a high pressure gas spring, fire and percussion prohibited. Also it is strictly prohibited to dismantle without professionals. Please return to the manufacturer or hand over to professional agencies if the product is abandoned.
-
The desk must be capable of supporting three times the weight of the total load (the mount, the monitor and all accessories weight). Don’t use the product on particle board.
Weight Restrictions
- 4.4-26.5 lbs. (2-12 kg)
Your monitor (including accessories) CANNOT EXCEED 4.4-26.5 lbs (2-12 kg) per arm
WARNING
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only with the maximum weights
indicated. Use with products heavier than the maximum weights indicated may
result in failure of the mount and its accessories, causing possible damage or
injury.
If your monitor weighs more, this mount is NOT compatible.
Check the VESA Pattern of Your Monitor before You Begin the Installation
- 75 mm ≈ 3 in.
- 100 mm ≈ 4 in
If your Monitor VESA is greater than 100×100 mm/4×4 in. or less than VESA 75x75mm/3x3in., this mount is NOT compatible.
If this desk mount is NOT compatible, please contact customer service at support@ergear.com to find a compatible product.
Product Features
TENSION ADJUSTMENT SHOULD BE DONE ONLY AFTER MOUNT INSTALLATION
Warning Icon: Do not adjust tension without monitor
- Ensure monitor has been attached to the mount.
- Read your monitor box or manual to find out monitor net weight.
- Ensure the net weight of monitor (including accessories) is between 4.4~26.5 Ibs (2-12 kg) per arm.
Adjustment Sign
- Clockwise to reduce tension(carry less weight)
- Counter-clockwise to increase tension(carry more weight)
Warning
Tools Needed (Not lncluded)
Screwdriver
Supplied Parts and Hardware
Warning: This product contains
small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, contact our
customer service at support@ergear.com.
- Please note: Not all hardware included in this package will be used.
Supplied Parts and Hardware for Step 1
-
C-Clamp X1
-
Pole Assembly X1
-
**Cable Clip X2
**
-
Bolt (C) M6x12mm (4pcs)
-
(D) Butterfly Nut x1
-
(D) Grommet Bolt x1
-
(E) Locking Plate x1
-
(F) x1 5/32 in.(4mm) Allen Key
Supplied Parts and Hardware for Step 3
-
Arm X2
-
Extension Arm x2
-
**Locating Ring X2
-
**(G) Plastic Sleeve X2
-
(F) x1 1/8 in.(3mm) Allen Key
-
(F) x1 5/32 in.(4mm) Allen Key
Supplied Parts and Hardware for Step 3
-
Bolt (A) M4x12mm (X8)
-
Bolt (B-1) M4x16mm (X8)
-
**Spacer (B-2) 5mm (X8)
Supplied Hardware for Step 4 and Step 6
- (F) 13/64 in.(5mm) Allen Key
Supplied Part for Step 8
- Cable Cover x1
Install the Base
A. For Clamp Mounting
-
Detach the c-clamp entirely
-
Slide the cable clips [06] to pole assembly [05] and secure part [a] to pole assembly [05] Warning: Ensure bolts are secured firmly.
-
Connect part [b] to part [a] according to the thickness of the desktop.
-
Secure the pole assembly to the desktop
B. For Grommet Mounting
-
Install the grommet bolt [D] to the bottom of pole assembly [05] Warning: Ensure bolts are secured firmly.
-
Secure the pole assembly to the desktop with grommet
Install the Arms
-
Fasten the locating ring [07] at your desired height.
-
Slide the extension arms [02] to the pole assembly [05], and attach the plastic sleeves [G] to extension arms [02]
Warning: Ensure bolts are secured firmly. -
Attach the arms [01] to the extension arms [02
-
Secure the arms [01] to the extension arms [02] by tightening the preassembled set screw [S] using Allen key [F]
Warning: Ensure bolts are secured firmly.
Step 3 Attach Monitors to the Arms
3-1 Choose Proper bolts
Flat back monitor
Round back monitor
For VESA hole pattern:
- 3 in. (75mm) x 3 in. (75mm)
- 4 in. (100mm) x 4 in. (100mm
3-2 Install Monitors to the Arms
Screw Driver [Not Included]
- 0.1-0.2in.(3-5mm) spacing left
The tension is preset at 8.8~11 Ibs(4-5kg). After hanging the monitor to the mount, please release the monitor slowly to prevent it from falling suddenly.
Warning: Ensure bolts are secured firmly.
Adjust Gas Spring Tension
Be sure to keep the arm in horizontal position during adjustment. Or else, it would be difficult to adjust the mount or damage the mount.
- If the monitor can stay at the desired height by itself, no adjustment needed.
- If the monitor rises up, press the arm to keep it in horizontal position and then use the 13/64 in.(5mm) Alley key (F) to turn the bolt clockwise(“-” direction) to reduce tension of the arm only until the monitor can stay at the desired height by itself.
- If the monitor falls down, lift the arm to keep it in horizontal position and then use the 13/64 in.(5mm) Alley key (F) to turn the bolt counter-clockwise (“+” direction) to increase tension of the arm only until the monitor can stay at the desired height by itself.
Rotation Restriction
Tilt Adjustment
“+” Clockwise: Tighten
“-” Counter-clockwise: Loosen
Situation 1: If the monitor can stay at the desired tilt angle by itself, no
adjustment needed.
Situation 2: If the monitor can not stay at the desired tilt angle by itself,
turn the bolt clockwise or counter-clockwise as shown until the monitor can
stay at the desired tilt angle by itself.
Rotation Adjustment
360 Rotation
Only suitable for the monitors with the center of gravity in the center position
Route Cables along the Arms
Warning: Ensure bolts are secured firmly.
Thank you again for choosing this Ergear product!
All of us at Ergear do appreciate your product purchase. We hope that you are as happy with your product as we are designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us at support@ergear.com (US/CA/DE/UK/FR/IT/ES/AU)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>