ErGear EGESD8V Shaped Electric Standing Desk Instruction Manual

June 14, 2024
ERGEAR

ErGear EGESD8V Shaped Electric Standing Desk

ErGear-EGESD8V-Shaped-Electric-Standing-Desk-PRODUCT

Technical Support

Specifications

ErGear-EGESD8V-Shaped-Electric-Standing-Desk-FIG-1

INSTALLATION INSTRUCTION

Supplied Parts and Hardware

ErGear-EGESD8V-Shaped-Electric-Standing-Desk-FIG-2 ErGear-EGESD8V-Shaped-Electric-Standing-Desk-
FIG-3ErGear-EGESD8V-Shaped-Electric-Standing-
Desk-FIG-4 ErGear-EGESD8V-Shaped-Electric-
Standing-Desk-FIG-5 ErGear-EGESD8V-Shaped-
Electric-Standing-Desk-FIG-7

Assembling the Leg Sections

  • Assemble the left leg section (using the leg without a motor).

ErGear-EGESD8V-Shaped-Electric-Standing-Desk-FIG-8

Assemble the middle leg section ( using the leg with a small base already attached).

Assemble the right leg section (using the leg with a motor but no leg base attached). ErGear-EGESD8V-Shaped-Electric-Standing-Desk-
FIG-11ErGear-EGESD8V-Shaped-Electric-Standing-
Desk-FIG-12

  • Attach the rubber pads to the leg sections and crossbar connectors. ErGear-EGESD8V-Shaped-Electric-Standing-Desk-FIG-14

Assembling the Desktop

ErGear-EGESD8V-Shaped-Electric-Standing-Desk-FIG-15ErGear-EGESD8V-Shaped-Electric-Standing-Desk-
FIG-16

Attaching the Frame to the Desktop

Option A: Long Side of Desk on Your Right

Place the leg sections on the desktop. Then connect the leg sections together using the crossbar connectors.ErGear-EGESD8V-Shaped-Electric-Standing-Desk-
FIG-18

Secure the frame to the desktop. Then attach the controller to the desktop. You can attach the controller on the left or right side.ErGear-EGESD8V-
Shaped-Electric-Standing-Desk-FIG-19ErGear-EGESD8V-Shaped-Electric-Standing-Desk-
FIG-20

Secure the frame to the desktop. Then attach the controller to the desktop. You can attach the controller on the left or right side.ErGear-EGESD8V-
Shaped-Electric-Standing-Desk-FIG-21

Attaching the Transmission Rod

Setting the Desk Legs to the Same Height
Before attaching the transmission rod, measure the heights of the left and middle desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the left leg. Turn the rod to adjust the left leg so it’s level with the middle leg. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it.ErGear-EGESD8V-Shaped-Electric-
Standing-Desk-FIG-23ErGear-EGESD8V-Shaped-
Electric-Standing-Desk-FIG-24

  • Ensure the transmission rod is properly inserted into the hole in the left leg. Smoothly connect the other end of the rod to the end of the motor drive shaft on the middle leg.ErGear-EGESD8V-Shaped-Electric-Standing-Desk-FIG-25

Secure the transmission rod to the motor drive shaft by turning the set screw clockwise. Then tighten the coupling nut to fine-tune transmission rod fit.

Connecting the Cables

Option A: Long Side of Desk on Your Right

ErGear-EGESD8V-Shaped-Electric-Standing-Desk-FIG-26

Option B: Long Side of Desk on Your LeftErGear-EGESD8V-Shaped-Electric-
Standing-Desk-FIG-27

Using the Controller

Raise the Desk

Press the UP button to raise the desk continuousiv until it reaches the highest position or the button is released.

Lower the Desk
Press the V button to lower the desk continuously until it reaches the lowest position or the button is released

Save Current Height Setting
Press and hold the or button for 3 seconds to save the current height setting as the standing height or sitting height. Short-press the or button, and the desk will move to the height that was previously set for that button.

Reset
Press and hold the V button for 5 seconds, and the screen will show ‘RST! Continue holding until the desk goes down to its lowest level and comes back up slightly. It will make a beep sound, and reset is complete.

Main Screen
The main screen displays the current date, time, and temperature.

Clock Settings Menu
Press and hold the and buttons together for 3 seconds to enter the clock settings menu. Short-press the button to cycle through the settings (Year – Month – Day – Hour – Minute – Temperature Unit – Sedentary Reminder). Short- press the UP or DOWN button to adjust the settings. Press and hold the and button again to save the changes. If there is no button press for 5 seconds, the clock settings menu will be exited automatically.

System Settings Menu
Press and hold the UP and DOWN buttons together for 3 seconds to enter the system settings menu. Short-press the UP or DOWN button to navigate through the menu. Short-press the button to select the settings; then short- press the UP or DOWN button to adjust the settings. Short-press the button again to save the changes and return to the system settings menu. If there is no button press for 5 seconds, the system settings menu will be exited automatically.ErGear-EGESD8V-Shaped-Electric-Standing-Desk-
FIG-31

Thank you for choosing this product. We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us.

Technical Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals