Ergear EGESD6V-3 Electric Standing Desk with Drawer Instruction Manual

June 14, 2024
ERGEAR

ErGear Logo GFGGGI’
48″ Electric Standing Desk
Instruction Manual
Rev00(A)
[EcEsD5B-3 | EGESD5V-3 Ergear EGESD6V-3 Electric Standing Desk with
Drawer

Technical Support:

(Us/cA) 1-800-651-9525
Mon~—Fri, 8am—-8pm (CST)
(UK) 44-808-196-3875 Mon—Fri, 2pm-10pm (UTC)
Other Info: support@ergear.com
Website: https://ergear.com

Specifications

Height Adjustment Range 28.3″-46.5″ (72-Ti8cm)

ErGear EGESD5V 3 Electric Standing Desk with Drawe -
Range

Step 1 Supplied Parts and Hardware

ErGear EGESD5V 3 Electric Standing Desk with Drawe - Range
1

Step 2 Supplied Parts and Hardware

ErGear EGESD5V 3 Electric Standing Desk with Drawe -
Hardware

Step 3 Supplied Parts and Hardware

ErGear EGESD5V 3 Electric Standing Desk with Drawe - Hardware
1

Step 4 Supplied Parts and Hardware

ErGear EGESD5V 3 Electric Standing Desk with Drawe - Hardware
2

Step 5 Supplied Parts and Hardware

ErGear EGESD5V 3 Electric Standing Desk with Drawe - Hardware
3

Step 1 Assembling and Connecting the Desk Legs

ErGear EGESD5V 3 Electric Standing Desk with Drawe -
Lage

ErGear EGESD5V 3 Electric Standing Desk with Drawe - Lage
1

Step 2 Attaching the Side Plates and the Transmission Rod

ErGear EGESD5V 3 Electric Standing Desk with Drawe - Lage
2

ErGear EGESD5V 3 Electric Standing Desk with Drawe - Lage
3

ErGear EGESD5V 3 Electric Standing Desk with Drawe - Lage
Road

Before attaching the transmission rod,  measure the heights of the two desk legs to see |f they are set at the same level. If not, insert the transmission rod into the hole in the left leg. Turn the rod to adjust the left leg so it’s level with the right leg. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it.

ErGear EGESD5V 3 Electric Standing Desk with Drawe - Lage Road
1

Ensure the transmission rod is properly inserted into the hole in the left leg. Smoothly connect the other end of the rod to the end of the motor drive shaft on the right leg.

ErGear EGESD5V 3 Electric Standing Desk with Drawe - Lage Road
2

Secure the transmission rod to the motor drive shaft by turning the set screw clockwise.

ErGear EGESD5V 3 Electric Standing Desk with Drawe - Lage Road
3

Step3  Assembling and Attaching the Desktop Assemble the desktop.

ErGear EGESD5V 3 Electric Standing Desk with Drawe -
desktop

ErGear EGESD5V 3 Electric Standing Desk with Drawe - desktop
1

Attach the hooks, controller, and drawer side plates to the desktop.

ErGear EGESD5V 3 Electric Standing Desk with Drawe - desktop
2

Step 4 Connecting the Cables

ErGear EGESD5V 3 Electric Standing Desk with Drawe -
Cabeles

Step 5 Assembling the Drawer

ErGear EGESD5V 3 Electric Standing Desk with Drawe - Cabeles
1

Step 6 Inserting the Drewer

ErGear EGESD5V 3 Electric Standing Desk with Drawe - Cabeles
2

Using the Controller

ErGear EGESD5V 3 Electric Standing Desk with Drawe -
Controll

  • Save Current Height Setting
    Short-press the (s] button, and the display will flash. Press the (1], (2], or [3] button to save the current height setting to that button.

  • Select Height Setting 1
    Press the (1] button, and the desk will move to the height that was previously set for that button.

  • Select Height Setting 2
    Press the (2] button, and the desk will move to the height that was previously set for that button.

  • Select Height Setting 3
    Press the (3] button, and the desk will move to the height that was previously set for that button.

  • Raise the Desk
    Press the ( ) button to raise the desk continuously until it reaches the highest position of 46.5” (118cm) or the button is released.

  • Lower the Desk
    Press the ( )button to lower the desk continuously until it reaches the lowest position of 28.3” (72cm) or the button is released.

Settings

Change Display Height Units| Press and hold the [s] button until a flashing ‘S- is displayed.
Press (s] again, and ‘Un’ is displayed. Press [§] to select it, press or  to switch between ‘IN’ (imperial) and ‘Sl
(metric), and press to save your choice.
---|---
Change Collision Detection Sensitivity| Press and hold the [s] button until a flashing ‘S-” is displayed.
Press [s] again, and ‘Un’ is displayed. Press or [s] to switch to ‘CF and press [s] to select it. Press or (s) to switch between off, low, normal, and high sensitivity. Press (s] to save your choice.
Reset| Press and hold the button for 5 seconds, and the screen will show ‘RES.” Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

Hot| Overheating Protection: When the motor has been working continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least 18 minutes before making any further height adjustment.
---|---
EI0| Sensor Malfunction Warning: Motor safety sensor can’t be detected. Power off, check the connection between the motor and controller, and power back on again.
E20| Overloading Warning: Max load exceeded. If raising the desk, take the things off the desk and try again. If lowering the desk, power off, take the things off the desk, power back on, and try again.
E02| Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.
E32| Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E31| Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E60| Unequal Leg Height Warning: Power off the desk and check whether the left and right legs are at the same height. Adjust if necessary by following the instructions. Power on again.
–| Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.

Complete Flexibility.
Total Freedom.
Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.

Technical Support
(Us/cA) 1-800-651-9525 Mon—Fri, 8am—-8pm (CST)
(UK) 44-808-196-3875
Mon—Fri, 2pm-10pm (UTC)
Other Infosupport@ergear.com
Websitehttps://ergear.com
860-00288-04 Rev00

Documents / Resources

| Ergear EGESD6V-3 Electric Standing Desk with Drawer [pdf] Instruction Manual
EGESD6V-3 Electric Standing Desk with Drawer, EGESD6V-3, Electric Standing Desk with Drawer, Standing Desk with Drawer, Desk with Drawer, Drawer
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals