AVIAN-X AVXDP100 Powerpro Smart Mallard User Manual

POWER LIGHT™
SMART MOTION MALLARD™
User’s Manual

DECOY ASSEMBLY

1. Face the decoy with the head pointed away from you and the top of the decoy facing up.
2. Take the wing with the “L” on the shaft. Line up the pin on the decoy shaft with the pin in the wing shaft on the left side of the decoy.
3. Push wing onto decoy shaft.
4. Take the wing with the “R” on the shaft. Line up the pin on the decoy shaft with the pin on the wing shaft on the right side of the decoy.
5. Push wing onto decoy shaft.

BATTERY INSTALLATION

1. With the decoy head facing away and the top of the decoy facing up grasp the feathers of the tail.
2. Gently pull up about an inch and then back to release the tail.
3. Move tail to the side of the decoy.
4. Hold the battery on the side with the charging port and cord. Make sure the post on the battery is facing up.
5. Slide the battery into housing with the cord out and push inside until it locks in place.
6. The plug battery pack in.
7. Take the tail and slide the rubber “T” into the slot in the decoy body while pushing down on the back of the tail.

BATTERY REMOVAL

1. With the decoy head facing away and the top of the decoy facing up grasp the feathers of the tail.
2. Gently pull up about an inch and then back to release the tail.
3. Move tail to the side of the decoy.
4. Disconnect battery.
5. Push the button on top to unlock and release the battery.
6. Take the tail and slide the rubber “T” into the slot in the decoy body while pushing down on the back of the tail.

STAKE ASSEMBLY

1. The stake can be used with 2 or 3 sections depending on how high off the ground you want the decoy.
2. To assemble the stake follow the diagram.
3. To mount to the decoy, take the square end and push the square post of the decoy into the stake.

DECOY OPERATION

1.  To power on the decoy, use the switch on the bottom of the decoy. The switch is printed with “- ” which means REMOTE, “0” which means OFF, and “=” which means SPIN.

REMOTE OPERATION

1. Turn the switch to the “APP/REMOTE” position on the decoy.
2. For the “SPIN” motion press the button that is printed with “SPIN”.
3. For “INTERMITTENT” motion press the middle button that is printed with “INTERMITTENT”.
4. To turn motion “OFF” press the bottom button that is printed with “OFF”.

REMOTE BATTERY REPLACEMENT & PAIRING

Remote Battery Replacement

1. Turn the remote so the back is facing up.
2. Remove the two screws holding the battery cap on.
3. Lift the Battery cap off to expose the battery.
4. Replace the battery with the new CR2032 (Positive/+ side up).

Remote Pairing: these instructions can be used to pair a replacement remote to the current decoy or to pair multiple decoys to one remote.

1. Turn on the decoy with battery in the decoy and turn the switch to “REMOTE”.
2. Press and hold the “SPIN” button on the remote for more than 4 seconds and release.
3. The LED inside the decoy will be flashing.
4. Press the “SPIN” button once and release it.
5. The LED inside the decoy will stop flashing when it is paired.

CHARGING BATTERY

Charging Battery Inside Decoy

1. Turn the decoy upside down.
2. Locate the charging port at the rear of the tail.
3. Insert charger cord and plug the charger in.
4. The light on the battery will be RED when charging and GREEN when Charged.
5. When complete remove the charging cord.

Charging Separate Battery

1. To charge a decoy battery locate the charging port on the side of the battery.
2. Open the charging port by pulling the plug out.
3. Insert charger cord and plug the charger in.
4. The light on the battery will be RED when charging and GREEN when charged.
5. When complete remove the cord and insert the plug.

STORAGE & TRANSPORTATION

1. When storing the decoy, the wings should be removed and stored flat and in a safe place to avoid damage.
2. The battery should also be removed and stored in a cool dry location.
3. For transporting the decoy, the wings should be removed to avoid damage to the wings.

PARTS LIST

Tail Bungee
• Charger
• Stake
• Tail| • Feet (set)
• Remote
• Wings (set)
• Battery
---|---

The Avian-X Smart Motion decoy can be remotely controlled by either the provided hardware remote or from your mobile device through the Avian-X FactorTM app. The hardware remote controls the decoy’s simplest functions, but to harness the full customization and control of the decoy you’ll want to download and use the mobile app.

1. After you’ve assembled the decoy and powered it on, flip the switch on the underside of the decoy to “Remote/App”.

2. Download the Avian-X FactorTM app from the Apple app store or Google Play.

3. Register a new account or log in.

4. To add a Smart Motion decoy, locate the “Decoys” tab in the footer navigation. Click “ADD” in the upper right-hand corner to pair to the decoy. Add as many decoys as you’d like in the app using this method.

5. Name the decoy, select the desired mode, start and stop this single decoy all within that individual decoy’s device card.

LINKING MULTIPLE DECOYS

For larger spreads and maximum attraction, you can link multiple decoys into a group to be controlled together. Click “Edit” (the pen) on the right side of the decoy card and toggle the “Link to group” switch.

CUSTOM MODES

Each decoy can be customized specifically to your liking, weather conditions, and overall spread setup. Mixing multiple decoys’ with different custom modes can also add to the overall realism of your spread. Navigate to “Profile” in the main footer navigation and select “custom modes”. Add consecutive steps specifying wing rotation, speed, duration, and the time delay between each step.

SOUND ACTIVATION

The Sound Activation feature uses your mobile device’s microphone to listen for, and analyze, the sound of a duck or goose call. Once heard the sound will automatically activate a function of the decoy. This conserves battery life during slow activity and is also realistic to approaching birds.

FACTORY RESET

Should you need to pair a different or new mobile device to your decoy there is a small red button on the decoy itself. This red reset button will return the decoy to factory settings. To reset, hold the red button down until the red light flashes and releases. The light should then turn green indicating the decoy is fully reset.

WARRANTY

DISCLAIMERS
Avian-X is not responsible for damage, expense, or injury caused by the unauthorized use of, alterations to, improper connection of, and abuse or neglect of Avian-X products.

WARRANTY
For the warranty to be in effect, register your product at avian-x.com /warranty-registration. Follow the on-screen directions to complete the process.
Avian-X will replace all workmanship defects free of charge for ONE (1) YEAR after the date of purchase as long as your warranty is in effect. This warranty DOES NOT COVER damage, expense, or injury caused by unauthorized repairs, alterations, improper connection, shipping, abuse, theft, accident, neglect, or collateral loss.

CUSTOMER SERVICE
Avian-X stands behind every product we manufacture for a one-year product workmanship warranty and a strong commitment to customer service. If you are in need of customer service for missing parts or need assistance with the operation or assembly of your product, we encourage you to call one of our customer service representatives and let us assist you. 877-269-8490

DISCLAIMER
Avian-X reserves the right to make changes to product features, functionality, and physical design at its sole discretion. As a result, such changes may not be reflected in this version of the manual.

FCC & IC

FCC STATEMENT
Product Name: Powerpro Smart Mallard
Trade Name: Avian-X
Model#: AVXDP100 (Main Unit)
Model#: AVXDPRCO1 (Remote)
FCC ID: YTTAVXDP100
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two criteria: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

ISED COMPLIANCE STATEMENT
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the FOL lowing two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.

GSM, LLC
P.O. Box 535189
Grand Prairie, Texas 75050
Toll-free 877-269-8490
www.gsmoutdoors.com
Avian-X is a registered mark of Zink Calls, Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>