BORMANN PRO BTC5500 Tile Cutter User Guide

BORMANN PRO BTC5500 Tile Cutter

Product Usage Instructions

Assembly Instructions
Follow the steps below to assemble the product

1. Fasten the table to the fastening assembly using Phillips B (4) 5x30mm screws.
2. Fasten the rail to the power head assembly with A (2) Phillips 6x50mm screws.
3. To install the handle, remove the pre-installed hex head screws on the power assembly.
4. Insert the handle and align the holes in the handle with the holes in the power assembly.
5. Replace and tighten the hexagonal socket screws in their original sockets.

Blade Adjustments
To hone the blade, follow these steps

1. Push the handle down until the blade is open 6mm/1/4.
2. Place a flat surface of the grinding stone on the blade and slide edge to edge 2 to 3 times.
3. This removes the small burr that forms when cutting hard products.

For blade sharpening and replacement, contact after-sales service for appropriate instructions.

Cut Guide
CAUTION! Always use hand protection while using the tool. Refer to the cut guide for recommended products and thicknesses.

FAQ
Q: Can I use this tool to cut metal?
A: The user manual does not specify cutting materials. It is recommended to refer to the cut guide for information on recommended products and thicknesses.

SYMBOLS

SAFETY INSTRUCTIONS

Warning: Read the manual carefully before use. Failure to follow the warnings and instructions may result in tool damage, physical injury and/or damage to property. Store the manual in a safe place for future reference.

• Read and understand this instruction manual before operating.
• Stay alert. Do not operate while under the influence of drugs, alcohol, or medication.
• Always wear safety approved eye protection with side shields.
• Keep work area clean and free of debris.
• Keep children and unauthorized persons away from the laminate cutter and the work area.
• Make sure tool is secure. Operate only on a firm substrate or solid stand.
• Use the right tool. Do not push the cutter and do not use it for work for which it is not intended. This tool is designed to cut: residential grade/low-pressure laminate flooring, engineered wood flooring, vinyl composite tile, PVC tile, fiber cement board siding, vinyl siding, and pressboard lap siding. (*see Cut Guide).
• Keep the blade sharp. A dull blade will not perform properly.
• Always keep hands away from the blade while operating or carrying the tool.
• Do not alter or misuse this tool. It is manufactured with precision; modifications not specified in this manual may result in dangerous conditions.
• Maintain with care. Follow the instructions for cleaning, lubricating and changing accessories.
• Use only recommended accessories. The use of improper accessories may cause hazards or injury.
• Never leave the cutter unattended. Secure the handle with the safety lock when not in use (*see Cuts).
• Warning: the dust generated by cutting certain wood, wood fiber and/or PVC products can be injurious to your health. The laminate cutter generally does not produce any dust; however, minimal dust may be generated. Avoid ingesting dust generated during cutting.

TECHNICAL SPECIFICATIONS

Technical data

Model| BTC5500
Cut Width| 330 mm
Cut Thickness| 15 mm
Material| Steel and aluminium
Angle Cut| 45°-90°
Cut| Seamless
Operation| Quick, No Noise, No Dust
Other features| No sharp edge, long handle for more power, compact design

• The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
• Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.

ASSEMBLY INSTRUCTIONS

Note! #2 Phillips head screwdrivers will be required. Hex key and hex screws are enclosed.

1. Fasten the table to the fastening assembly using Phillips B (4) 5×30 mm screws.
2. Fasten the rail to the power head assembly with A (2) Phillips 6×50 mm screws.
3. To install the handle, first remove the hex head screws (pre-installed on the top of the power assembly).
4. Insert the handle and align the holes in the handle with the holes in the power assembly. (Make sure that the recesses in the handle are aligned with the screw holes in the power assembly for proper placement of the handle)
5. Replace and tighten the hexagonal socket screws in their original sockets. (The screws should tighten easily if properly aligned (hardware kit C)

Blade Adjustments

Honing the Blade
Push the handle down until the blade is open 6mm/1/4″. Place a flat surface of the grinding stone on the blade and slide edge to edge 2 to 3 times. This removes the small burr that forms when cutting hard products.

Blade Sharpening & Blade Replacement
The blade can be sharpened several times before a replacement blade is necessary. Replace with the appropriate blade (contact after-sales Service).

Cut Guide
CAUTION! USE HAND PROTECTION
The tool cuts a wide variety of products. Please refer to this cut guide for recommended products and thicknesses:

Laminate Flooring

(Residential Grade ACL AC2 and AC3 only-

Not Intended for Commercial Grade Laminates)

|

15mm or 9/16″

---|---
Engineered Wood| 10mm or 3/8″
Parquet| 12mm or 1/2″
PVC Tile| 12mm or 1/2″
Vinyl Composite Tile| 12mm or 1/2″
Rubber Tile| 15mm or 9/16″
Carpet Tile| 12mm or 1/2″
Soft Plastic| 12mm or 1/2″
Leather| 15mm or 9/16″
Cork| 15mm or 9/16″
Wood Siding| 15mm or 9/16″
Fiber Cement| 15mm or 9/16″

Blade Adjustment Instructions

1. Unscrew and remove the adjustment plate screws.

2. Tighten both adjustment plates by 1 or 2 holes.
   Note! The pitch on each lifting screw is 0,125 mm. The adjustment on both plates must be the same.

3. Cut a piece of paper to ensure that the tool is set up correctly.

Cuts
Caution! Make sure you wear hand and eye protection during operation.

1. While gently pushing the handle down, slide the safety catch inwards and then lift the handle. Important: Hold the material firmly in place to ensure a clean precision cut.
2. Place the material to be cut on the table. Bring the handle down until the blade touches the material. Warning! The blade is very sharp. Keep fingers away from the blade.
3. Press the handle completely down to cut the material.
4. The safety lock must be placed in the locked position after you have completed the work.

Warning! Disabling the reset function on the safety lock is potentially dangerous.
Important! After every 500 cuts, it is recommended to lubricate the driving sleeve with 10W-30 engine oil from above after removing the black caps. This will prevent premature wear of the machine.

WWW.NIKOLAOUTOOLS.COM

The instructions manual is also available in digital format on our website www.nikolaoutools.gr. Find it by entering the product code in the Search “ ” field.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>