guardian technologies AP6100 Pro Max Dual HEPA Air Purifier Instruction Manual

guardian technologies AP6100 Pro Max Dual HEPA Air Purifier

READ AND SAVE THESE INSTRUCTIONS

WARNINGS

Failure to comply with the warnings listed below may result in electric shock or serious injury.

This product should be used only in accordance with the specifications outlined in this manual. Usage other than what has been specified here may result in serious injury.

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

• Read all instructions before using the appliance.

• IMPORTANT: This appliance has a polarized plug (one blade is wider than the other).

• To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

• To avoid fire or shock hazards, plug the appliance directly into a 120V AC electrical outlet.

• Keep the cord out of heavy traffic areas. To avoid fire hazards, NEVER put the cord under rugs, near heat registers, radiators, stoves or heaters.

• To protect against electrical hazards, DO NOT immerse in water or other liquids.Do not use near water. Extreme caution is necessary when any appliance is used by or near children or people
  with disabilities and whenever the appliance is left operating unattended.

• Always unplug the air purifier before moving it, opening the grill, changing filters, cleaning, or whenever the air purifier is not in use. Be sure to pull by the plug and not the cord.

• NEVER drop or insert any object into any openings.

• DO NOT run cord under carpeting.

• DO NOT cover cord with throw rugs, runners, or similar coverings.

• DO NOT route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.

• DO NOT use with an extension cord. Always plug directly into the outlet. • DO NOT operate any appliance with a damaged cord or plug, if motor fan fails to rotate,
  after the appliance malfunctions, or if it has been dropped or damaged in any manner. Call Customer Service.

• Use appliance only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons.

• DO NOT use outdoors.

• DO NOT place anything on top of the unit.

• NEVER block the air openings, grills/outlets or place on a soft surface such as a bed or sofa, as this could cause the unit to tip over, blocking the air intake or outtake opening.

• DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit.

• Doing so will void your warranty. The inside of the unit contains no user-serviceable parts. All servicing should be performed by qualified personnel only.

• WARNING: To reduce the risk of fire or electric shock, do not use this purifier with any solid-state speed control device.

• Always unplug the unit before cleaning or servicing in any way.

• CAUTION: Do NOT use gasoline, benzene, thinner, harsh cleaners, etc. on and/or in the unit while cleaning as they will damage the product. NEVER use alcohol or other solvents

WARNING: Cancer and Reproductive Harm. For more information go to www.P65Warnings.ca.gov.

This product earned the ENERGY STAR label by meeting strict energy efficiency guidelines set by the U.S. EPA. Room air cleaners have demonstrated the potential for improving air quality and providing health benefits. EPA does not endorse manufacturer claims regarding the degree to which a specific product will produce healthier indoor air. The energy efficiency of this ENERGY STAR certified model is measured based on a ratio between the model’s CADR for Smoke and the electrical energy it consumes, or CADR/Watt.

PRODUCT SPECIFICATIONS AND PARTS

• DIMENSIONS: 17.7” L X 15.3” W X 30.5” H
• WEIGHT: 37.1 LBS
• INPUT VOLTAGE: 120V; 60Hz
• RATED POWER: 120 W

CONTROL PANEL

INDICATOR & FUNCTION

• Temperature: Displays Temperature in degrees Fahrenheit
• Child Lock Icon: Illuminates when the Child Lock feature is turned on
• Night Mode Icon: Illuminates when the Night Mode is on
• Auto Icon:  Illuminates when the Auto feature is on
• Filter Replacement: Illuminates when the filter has reached 6 months of use
• AQI Reading: AQI readings should be between 1-500 and based on the EPA’s AQI scale
• AQI Color: AQI Readings between 1-100 (Green), 101-200 (Yellow), 201-500 (Red)
• Fan Speed: Should be a number between 1-5

OPERATING INSTRUCTIONS

IMPORTANT: The air purifier is shipped with the filters stored in the filter compartments. The filtes are shipped in bags to prevent degradation. Before using, remove and discard bags.

The filtes are shipped in bags to prevent degradation. Before using, remove and discard bags.

SET UP PRODUCT FOR USE

1. Select a firm, level, and flat location for the air purifier. The purifier is equipped with wheels for easy transport.

• For proper air flow, locate the unit at least 1 foot from any wall or furniture.
• Make sure none of the grills are blocked.

1. Plug the power cord into a 120V AC outlet.

OPERATING THE AIR PURIFIER

1. Turn unit power ON by touching the control icon on the top of the unit. When the device is turned on, the power LED is fully on. By default, it remains half on when the device is switched off.

Note: The purifier will not work if both side filter panels are not closed. The first time the unit is plugged in and powered on, the air quality sensor will take 1 minute to calibrate.

Fan Speed:  Select between level 1-5 fan speeds. Increase or decrease by touching the fan icons. Each touch will change the fan speed by 1 level.

1. Child Lock: Touch and hold for 3 seconds to lock the control panel so controls cannot be adjusted. Touch and hold for 3 seconds again to turn the feature off.
2. Sleep Mode:  Sleep mode is activated by pressing the Child Lock and Auto button for 3 seconds. When turned on the unit will run at the lowest fan speed and turn off all lights except for the power button.
3. Auto Mode: Touch control to select Auto Mode on/off. When in “Auto” the fan speed will change depending on the air quality level in the room. See QAM below. Optical Sensing in “Auto” mode: when the room is dark for over 1 minute, the unit will enter into sleep mode automatically (dim display). When the sensor detects the room is light, the unit will restore to standard Auto mode after one minute.
4. Filter Change Indicator illuminates to indicate it is time to change the filter. Replace the filter according to instructions (Pg. E7). Touch and hold Auto control for 3 seconds to reset the reminder and indicator light.
5. Air Quality Monitor (QAM): detects the amount of particulate matter (PM2.5) in the air. The light bar under the display is the QAM indicator and it will change colors, indicating the air quality level in the room. The particulate matter value will be displayed on the control panel. See values and status ranges in chart below.

Light Color| Particulate Matter Value (Range)| Air Quality Status
---|---|---
Green| 0-100| Good
Yellow| 101-200| Average
Red| 201+| Poor

The colors displayed to indicate the general air conditions in the room: good (green); average (yellow); red (poor).

RESETTING THE AIR PURIFIER

The air purifier is equipped with a motor protection circuit. If activated, the overload warning indicator will initiate and cut off the power. An audible warning “chime” will sound for 60 seconds along with a flashing error “Error” warning on the display. To restart the unit, unplug the unit for 10 minutes, then plug back in and power on.

Note: If the unit continues to shut down, there may still be an abnormal condition and the unit may need service.

FILTER REPLACEMENT

The Replace Filter Indicator light will illuminate when it is time to replace the carbon and HEPA filters, depending on usage and environmental conditions the filters will last approximately6 months. The filters will be covered in dust when dirty and need replacing. It is important to maintain and change the filters to continue to optimize the performance of the purifier.

IMPORTANT: DO NOT wash and re-use the filters. Please contact Customer Service to purchase replacement filters. Use only Genuine Guardian Technologies Replacement Parts to optimize the performance of your air purifier.

1. Turn off and unplug the unit.
2. Remove the side panel by grasping the cover at the openings on each side, pull out then lift panel from base.
3. Remove and clean dust and debris from the pre-filter screen with a vacuum hose.
4. Remove and dispose of the carbon and HEPA filters.
5. Replace by first inserting HEPA filter, followed by the Activated Carbon filter, then the pre-screen. Secure the pre-screen by inserting into the frame into the openings in the base of the filter compartment.
6. Return the filter panel by inserting the base of the frame into the opening on the bottom of the purifier, then close at the top to secure.
7. Touch and hold the Auto control for 3 seconds to reset the reminder.

NOTE: Both sides of the machine have a filter. Removal and replacement instructions are the same. When finished, make sure both side filter panels are closed properly. Unit will not function when panels are open.

REPLACEMENT PARTS

Check out our

AutoShip & Save

• Filter Replacement Program
• www.guardiantechnologies.com

IMPORTANT: To maintain performance of the air cleaner, use Guardian Technologies GENUINE Replacement Parts only. To purchase visit our website www.guardiantechnologies.com.

CLEANING & MAINTENANCE

CLEANING

Always unplug the appliance before you clean it. Never immerse the appliance in water or any other liquid. Never use aggressive or flammable cleaning agents such as bleach or alcohol to clean any part of the appliance.

BODY OF THE APPLIANCE

Regularly clean the inside and outside of the body to prevent dust from collecting.

1. Wipe away dust with a soft dry cloth from the body of the appliance.
2. Clean the air inlet and the air outlet with a soft dry cloth.

PRE-FILTER SCREENS and CARBON FILTERS

The pre-filter is designed to collect larger dust and debris and should be cleaned monthly or more frequently depending on use. Clean regularly with the brush attachment or your vacuum cleaner. This will remove the lint and dirt and help maintain the life of the filter (see filter replacement to locate and remove filter).

DUST SENSOR

The dust sensor may need to be cleaned periodically. If the AQI isn’t working consistently the sensor should be cleaned. It is located in the sensor box in the lower-left corner of the filter compartment and can be cleaned with compressed air.

1. Locate the sensor box. Slide the sensor box forward.
2. Turn sensor to the right to access the sensor opening.
3. Gently clean the sensor, in the opening, with compressed air.

Note: Do NOT stick any foreign objects or your fingers inside the unit.

What is CADR?

CADR stands for “Clean Air Delivery Rate,” which indicates the volume of filtered air delivered by an air purifier. CADR ratings show the effectiveness of how efficient the air purifier is at capturing fine particles from things like tobacco smoke and plant pollens from the room.

Clean Air Delivery Rate

From air cleaner to air cleaner, compare the CADR numbers. First look at the suggested room size. Then refer to the Clean Air Delivery Rate (CADR) numbers. The higher the number, the faster the unit filters the air.

Refer to website for individual model CADR numbers

TROUBLESHOOTING GUIDE

plugged into a working electrical outlet. Check to see if the motor protector is triggered.

Check that the filters are in the unit and the panels are closed.

No air circulating from the unit.| Unplug unit. Check filters. Clean or replace filters if necessary.
Increase in noise level.| Make sure the filters are clean. Replace if necessary. Make sure the air vents are not blocked.

Turn the unit off and restart after 15 minutes.

Odors and smoke are not removed.| Clean or replace the fitlers.
The discharged air has an aroma or odor.| Check to see if the filters are heavily soiled. Replace the fitlers.
The unit automatically enters sleep mode in well-lit environments.| Check to make sure there is nothing blocking the light sensor.
Air quality status remains poor.| Check to see if the filter is heavily soiled. Replace if necessary. Increase the fan speed to circulate air.
The AQI display is not working properly.| Check to make sure the dust sensor is clean. Check to see if the filters are heavily soiled. Replace the filters.

LIMITED WARRANTY

To the consumer, Guardian Technologies LLC warrants this product to be free of defects in materials or workmanship commencing upon the date of the original purchase. In order to be eligible for this Limited Warranty, an original sales receipt or comparable substitute proof of purchase bearing the date of original purchase is required. Refer to the original product carton or specific product/model page on the Guardian Technologies website for warranty length for your particular model. This warranty applies only to the original purchaser of this product from the original date of purchase. This warranty covers product purchased from authorized distributors only. This warranty does not cover Guardian Technologies products that are used outside of the US and Canada as the appliance must be plugged directly into a 120V AC electrical outlet without the use of an adapter. This warranty applies to the repair or replacement of products found to be defective in materials or workmanship. This warranty does not apply to damage resulting from unusual wear, commercial, abusive, unreasonable use or supplemental damage. This warranty does not cover damage from unauthorized repairs or from any use not in accordance with the instruction manual. Defects that are the result of normal wear and tear will not be considered manufacturing defects under this warranty. If this product should become defective within the warranty period, we will repair or replace any defective parts free of charge. All warranty repairs must be completed by Guardian Technologies LLC. This warranty gives you specific legal rights and you may also have other rights (other rights may vary from state to state in the U.S.A.)

To submit the product under warranty the complete machine must be delivered pre-paid to Guardian Technologies LLC. Please include complete information including the problem, the model number of the product, the day of purchase, and a copy of the original sales receipt along with your name, address, and telephone (email optional). Address returns to the attention of Repair Department, at the address below. Additional questions or comments can be made toll-free to the number listed below.

USA and Canada

Guardian Technologies LLC

• 26251 Bluestone Blvd.
• Euclid, Ohio 44132
• 1.866.603.5900
• www.guardiantechnologies.com

Please go to www.guardiantechnologies.com to register your product. We consider the registration process important to ensuring superior service to our customers, however, submitting the registration is optionaland does not affect your rights to utilize this warranty according to the conditions stated above.

Additional copies of the instruction manual can be obtained by accessing and printing directly from our website or calling customer service.

Guardian Technologies LLC

• 26251 Bluestone Blvd.
• Euclid, OH 44132
• 1.866.603.5900
• www.guardiantechnologies.com

References

• Lasko, GermGuardian, B-Air, BlueDri | Fans, Heaters, Air Purifiers – GuardianTechnologies
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>