BEGA 12133PK4 Ceiling and Wall Luminaire for Indoor Instruction Manual

: August 13, 2024
: BEGA

Table of Contents

Instructions for use
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**BEGA 12133PK4 Ceiling and Wall Luminaire for Indoor Instruction Manual

**

Ceiling and wall luminaire for indoor use

Instructions for use

Application

Ceiling and wall luminaire · indoor luminaire made of impact resistant synthetic diffuser and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required.

Product description

Metal housing, finish colour white Impact resistant synthetic diffuser, white, with bayonet closure
2 mounting holes ø 5.5mm
Distance apart 180mm
2 cable entries for through-wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@
Connection terminal 2.5@
Earth conductor connection Complies with flicker requirements in accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 V y 50-60 Hz
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Impact strength IK08
Protection against mechanical
impacts < 5 joule
– Safety mark
– Conformity mark

Weight: 1.2 kg
This product contains light sources of energy efficiency class(es) D, E

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

Module connected wattage : 11.6 W
Luminaire connected wattage : 15.5 W
Rated temperature : ta=25 °C
Ambient temperature : ta max=45 °C

12 133 PK27

Colour temperature : 2700 K
Colour rendering index : CRI >90
Module luminous flux : 1670 lm
Luminaire luminous flux : 1272 lm
Luminaire luminous efficiency : 82,1 lm/W

12 133 PK3

Colour temperature : 3000 K
Colour rendering index : CRI >90
Module luminous flux : 1725 lm
Luminaire luminous flux : 1314 lm
Luminaire luminous efficiency : 84,8 lm/W

12 133 PK4

Colour temperature : 4000 K
Colour rendering index : CRI >90
Module luminous flux : 1795 lm
Luminaire luminous flux : 1367 lm
Luminaire luminous efficiency : 88,2 lm/W

Luminaire with trim ring:
Before installing onto the mounting surface the luminaire housing must be inserted into the trim ring (accessory).

Installation

LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Pass the mains supply cable through the grommet into luminaire housing.
Fix luminaire housing with enclosed or any other suitable fixing material on to the mounting surface.
It is imperative to use the enclosed gaskets.
Dismantle the mains supply cable approx. 60 mm.
Make earth and electrical connection to the terminals.
Place the synthetic diffuser to the luminaire housing and observe that the cam pins fit into the notches of the synthetic diffuser.
Screw in synthetic diffuser by turning it clockwise.
Thus, you reach a safe and vibrationresistant holding of the synthetic diffuser.
To release the synthetic diffuser from the luminaire housing, turn it counter- clockwise.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacement of the LED unit

The designation of the LED unit is noted on a label in the luminaire.
The light colour and light output of BEGA replacement units correspond to those of the LED units originally fitted. The LED unit can be replaced by qualified persons using standard tools.
Disconnect from main supply.
Unscrew synthetic diffuser from luminaire housing by turning it counter- clockwise.
Disassemble LED unit.
Assemble LED replacement unit.
Note installation instructions of the LED unit.
Screw in synthetic diffuser by turning it clockwise.
A damaged synthetic diffuser must be replaced.