EDCO TLR-7 Traffic Line Remover User Manual
- August 16, 2024
- EDCO
Table of Contents
TLR-7 Traffic Line Remover
“`html
Product Information
Specifications:
- Model: TLR-7
- Part Number: 77500
- Manufacturer: Equipment Development Company, Inc.
- Address: 100 Thomas Johnson Drive, Frederick, MD 21702-4600
USA
Product Usage Instructions
Safety Information:
Before operating the equipment, read and understand the
operator’s safety manual thoroughly to prevent accidents.
Keep body parts, loose clothing, and accessories away from
moving parts to avoid dismemberment or death.
Maintain a safe distance from flammable materials as sparks from
the machine can ignite them.
How to Order Replacement Parts:
To ensure product safety and reliability, always use genuine
EDCO replacement parts for repairs.
When ordering parts, provide the model and serial number of the
machine found on the nameplate. Specify part number, description,
and quantity as listed in the parts list to your parts
representative.
Illustration 1: Outer Frame Grouping
Refer to the parts listing for the outer frame grouping for
detailed information on each part.
Parts Listing – Illustration 1: Outer Frame Grouping
| Item # | Part # | Description |
|---|---|---|
| 1 | 68022 | OUTER FRAME W/ HANDLE, TLR-7 |
FAQ (Frequently Asked Questions)
Q: How do I find the model and serial number of the
machine?
A: The model and serial numbers are located on the nameplate of
the machine. Refer to the user manual for detailed instructions on
locating this information.
Q: Can I use non-genuine replacement parts for repairs?
A: It is recommended to always use genuine EDCO replacement
parts to ensure product safety and reliability. Non-genuine parts
may affect the performance and safety of the equipment.
“`
E-TLR7-PL-0624 REVISED STARTING SERIAL # 240610141
PARTS LIST MANUAL
MODEL TLR-7
TRAFFIC LINE REMOVER
PART NO. 77500
READ AND UNDERSTAND THE OPERATOR’S SAFETY MANUAL THOROUGHLY
BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT.
Death or serious injury could occur if this machine is used improperly.
Machine specific Operator’s Instruction Manuals are offered at edcoinc.com
/customer-support/parts-and-manuals READ AND UNDERSTAND THE ENGINE
MANUFACTURERS INSTRUCTIONS AND OPERATORS MANUAL BEFORE OPERATION.
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
8P0h0o-n6e3:88-0303-26638·-3e3d2c6ooinr c30.c1o-6m63·-1t6e0c0hs·uFpapxo:
r8t0@0-e4d4c7-o3i3n2c6.coor m301-663-1607 Website: www.edcoinc.com · E-mail:
techsupport@edcoinc.com
Printed in USA JWA ©2024
Page 1
E-TLR7-PL-0624
SAFETY INFORMATION
SAFETY MESSAGES
· Safety Instructions are proceeded by a graphic alert symbol of DANGER,
WARNING, or CAUTION.
Indicates an imminent hazard which, if not avoided, will result in death or
serious injury.
Indicates an imminent hazard which, if not avoided, can result in death or
serious injury.
Indicates hazards which, if not avoided, could result in serious injury and or
damage to the equipment.
ELECTRICAL POWERED EQUIPMENT CONTINUED
· Do not disconnect power by pulling cord. To disconnect, grasp the plug, not
the cord.
· Unplug power cord at the machine when not in use and before servicing.
· Switch motor OFF before disconnecting power. · Never use frayed, damaged,
taped or under rated extension cords.
Electrical shock could result in death or serious injury to the operator and
damage to the equipment. · Assure you are using the proper extension cord
length.
GASOLINE / PROPANE POWERED EQUIPMENT
· Engine exhaust from this product contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm. ·
Tilting a gasoline powered machine fitted with an EPA approved vented charcoal
filter gas cap, beyond 20° can cause fuel leakage. If a leak occurs, do not
start or run the engine until the leak is fixed. Eliminate all other ignition
sources in the immediate area (no smoking, flares, sparks or flames). Use
approved gasoline absorbing material to contain the fuel leakage. Then use
clean, non-sparking tools to collect absorbed materials then dispose of these
contaminants properly. · Gasoline is extremely flammable and poisonous. It
should only be dispensed in well ventilated areas, and with a cool engine. ·
Small gasoline engines produce high concentrations of carbon monoxide (CO)
example: a 5 HP 4 cycle engine operation in an enclosed 100,000 cu. ft. area
with only one change of air per hour is capable of providing deadly
concentrations of CO in less than fifteen minutes. Five changes of air in the
same area will produce noxious fumes in less than 30 minutes. Gasoline powered
equipment should not be used in enclosed or partially enclosed areas. Symptoms
of CO poisoning include, head-ache, nausea, weakness, dizziness, visual
problems and loss of consciousness. If symptoms occur – get into fresh air and
seek medical attention immediately. · Never refuel a hot engine or an engine
while it is running. · Engines are shipped from factory without fuel/oil. ·
Propane is extremely flammable and is heavier than air and tends to settle in
low areas where a spark or flame could ignite gas. DO NOT start or operate
this propane engine in a poorly ventilated area where leaking propane gas
could accumulate and endanger safety of persons in area. If headache develops,
shut off machine. Have it checked for carbon monoxide emissions by a qualified
technician before using it again. To ensure personal safety, installation and
repair of propane fuel supply systems must be performed only by qualified
technicians. Carbon monoxide emissions from this machine are greatly increased
due to a dirty combustion air cleaner.
ELECTRICAL POWERED EQUIPMENT
Extreme care must be taken when operating electric models with water present:
Ensure power cord is properly grounded, is attached to a Ground-Fault-
Interrupter (GFI) outlet, and is undamaged. · Check all electrical cables – be
sure connections are tight and cable is continuous and in good condition. Be
sure cable is correctly rated for both the operating current and voltage of
this equipment. · Improper connection of the equipment grounding conductor can
result in a risk of electric shock. Check with qualified electrician or
service person if there is any doubt as to whether the outlet is properly
grounded. Adhere to all local codes and ordinances. · NOTE: In the event of a
malfunction or breakdown, grounding provides a path of least resistance for
the electric current to dissipate. The motor is equipped with a grounded plug
and must be connected to an outlet that is properly installed and properly
grounded. DO NOT modify the plug provided on the motor. If the plug does not
fit the outlet have a qualified electrician install the proper receptacle.
GENERAL INSTRUCTIONS
· Equipment should only be operated by trained personnel in good physical
condition and mental health (not fatigued). The operator and maintenance
personnel must be physically able to handle the bulk weight and power of this
equipment.
· This is a one person tool. Maintain a safe operating distance to other
personnel. It is the operators’ responsibility to keep other people (workers,
pedestrians, bystanders, etc.) away during operation. Block off the work area
in all directions with roping, safety netting, etc. Failure to do so may
result in others being injured by flying debris or exposing them to harmful
dust and noise.
· This equipment is intended for commercial use only. · For the operator’s
safety and the safety of others, always keep all
guards in place during operation. · Never let equipment run unattended.
· Personal Protection Equipment and proper safety attire must be worn when
operating this machinery. The operator must wear approved safety equipment
appropriate for the job such as hard hat and safety shoes when conditions
require. Hearing protection MUST be used when operational noise levels of this
equipment may exceed 85db. Eye protection MUST be worn at all times.
Keep body parts, loose clothing and accessories away from moving parts.
Failure to do so could result in dismemberment or death.
· Do not modify the machine. · Stop motor/engine when adjusting or servicing
this equipment. Maintain
a safe operating distance from flammable materials. Sparks from the cutting-
action of this machine can ignite flammable materials or vapors.
DUST WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth
defects, or other reproductive harm. Materials being removed can be toxic or
hazardous. A breathing respirator is required to help protect the operator.
Some examples of these chemicals are: · Lead from lead-based paints. ·
Crystalline silica from bricks, concrete and other masonry products.Your risk
of exposure to these chemi cals varies depending on how often you do this type
of work. To reduce your risk: work in a well ventilated area, use a dust
control system, such as an industrialstyle vacuum, and wear approved personal
safety equipment, such as a dust/particle respirator designed to filter out
microscopic particles. · See more on the importance of dust prevention and
silica warnings at: osha.gov/silica · More concrete and silica dust supression
training and educational materials available at edcoinc.com/silica-standards
or scan the QR code on page 5. · Written exposure plans are provided at
http://www.edcoinc.com/writtenexposure-control-plans/
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
Page 2
E-TLR7-PL-0624
PARTS LIST MANUAL
MODEL TLR-7
TRAFFIC LINE REMOVER
TABLE OF CONTENTS
Section
Pages
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 How To Order Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Illustration 1: Outer Frame Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 5 Illustration 2: Inner Frame Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 7 Illustration 3: Handwheel & Linkage Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 9 Illustration 4: Rotary Cutter Head Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 11 Illustration 5: Engine & Belt Drive Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 13 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Illustartion 6: Kick Stand Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 17 Decal Sheet P/N 92219 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Limited Equipment Warranty of Sale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 EDCO’s Online Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
HOW TO ORDER REPLACEMENT PARTS
To insure product safety and reliability, always use genuine EDCO replacement
parts when making repairs to the equipment.
When calling for parts, specify the MODEL and SERIAL number of the machine,
which can be found on the NAME PLATE. Keep that information in the space
provided. In addition to this information, give part number, description, and
quantity as listed on the parts list to your parts representative.
Please note: Due to improvements and changes in the equipment, the
illustrations shown may be different than the actual machine.
FILL IN INFORMATION BELOW Date of Purchase __ Model # _____ Serial # __ SKU #
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
Page 3
E-TLR7-PL-0624
ILLUSTRATION 1: OUTER FRAME GROUPING
Page 4
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
E-TLR7-PL-0624
ITEM #
1 2 3 4 5 6 7
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
PARTS LISTING – ILLUSTRATION 1 : OUTER FRAME GROUPING
PART #
DESCRIPTION
68022
OUTER FRAME W/ HANDLE, TLR-7
10953
FITTING, GREASE 1/8 NPT STRAIGHT
10608
GRIP, HAND 1″ MODEL AT
14023
KNOB, BALL 1-3/8 W/ 1/2-13THD, BLK.
68081
PLUNGER, SPRING 5/8-11 THD.
10046
NUT, HEX 5/8-11 ZINC
68036
KICK STAND ASSY., TLR-7 (SEE ILLUSTRATION 6 FOR BREAKDOWN)
10053
SCREW, CAP 5/16-18 X 3/4 ZINC
10801
WASHER, LOCK 5/16 ZINC
10054
NUT, HEX 5/16-18 ZINC
68020
CASTER, SWIVEL 5″WHEEL W/3/4-10STEM
10009
WASHER, FLAT 3/4 SAE ZINC
10403
NUT, HEX JAM 3/4-10 ZINC
10609
WASHER, LOCK, INT. TOOTH 3/4″
68058
NUT, HEX NYLON JAM 3/4-10 ZINC
68046
HOLDER, FRONT AXLE, TLR-7
10052
SCREW, SET 5/16-18 X 3/8
10312
WASHER, FLAT 1/2 SAE ZINC
10045
WASHER, LOCK 1/2 ZINC
10143
BOLT, TAP 1/2-13 X 1-1/2 (FULL THD)
68045
AXLE SHAFT, FRONT 23″L, TLR-7
68047
SPACER, FRONT AXLE, TLR-7
50222
BEARING, BALL 1″ TPB
68008
WHEEL 8 X 1-5/8 X 3/4″BRG., POLY
10009
WASHER, FLAT 3/4 SAE ZINC
10306
PIN, COTTER 3/16 X 1-1/2
10318
SCREW, CAP 3/8-16 X 3-3/4 ZINC
10811
WASHER, LOCK 3/8 ZINC
10025
WASHER, FLAT 3/8 SAE ZINC
68037
WEIGHT, 41 LB., TLR-7
68038
WEIGHT BAR, 7 LB., TLR-7
10312
WASHER, FLAT 1/2 SAE ZINC
10045
WASHER, LOCK 1/2 ZINC
68040
NUT, TAIL HANDLE 1/2-13, TLR-7
QTY.
1 1 2 1 1 1 1
3 3 3 2 2 2 2 2 2 2 4 4 4 1 2 2 2 2 2 4 4 8 2 2 2 2 2
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
Page 5
E-TLR7-PL-0624
ILLUSTRATION 2: INNER FRAME GROUPING
Page 6
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
E-TLR7-PL-0624
ITEM # 1 2 3 4 5 6 7 8 9 10
11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26
27
PARTS LISTING – ILLUSTRATION 2 : INNER FRAME GROUPING
PART #
DESCRIPTION
68021
FRAME, INNER, TLR-7
10417
NUT, HEX 1/2-13 ZINC
10340
BOLT, TAP 1/2-13 X 3 (FULL THREAD)
64030
CAP, END 3″ BLUE PLASTIC
68057
COVER, BELT, TLR-7
68056
COVER REAR PANEL, BELT, TLR-7
10018
SCREW, CAP 1/4-20 X 3/4 ZINC
10038
WASHER, LOCK 1/4 ZINC
10602
WASHER, FLAT 1/4 SAE ZINC
68025A
GUARD & SKIRT SUBASSEMBLY, TLR-7 (INCLUDES ITEMS 11 THRU 19)
68025
GUARD, CUTTER HEAD, TLR-7
68026
RETAINER, SKIRT 12″, TLR-7
68028
RETAINER, SKIRT 5-1/2″, TLR-7
68029
RETAINER, SKIRT 3-1/4″, TLR-7
68030
SKIRT, RUBBER, TLR-7 3″ X 108″(9 FT.) X 1/16″THK.
10412
BOLT, CARRIAGE 1/4-20 X 1 ZINC
10602
WASHER, FLAT 1/4 SAE ZINC
10038
WASHER, LOCK 1/4 ZINC
10013
NUT, HEX 1/4-20 ZINC
79012
BEARING, BALL 1-1/4″ 4-HOLE FLANGE
10006
FITTING, GREASE 1/8 NPT X 45D
10409
SCREW, CAP 1/2-20 X 4-1/2 ZINC
10312
WASHER, FLAT 1/2 SAE ZINC
10045
WASHER, LOCK 1/2 ZINC
10205
NUT, HEX LOCK 1/2-20 ZINC
68019
SPACER, ROTARY HEAD MAIN SHAFT 1-1/2″OD X 1-1/4″ID X 1/2″THK
68068
SPIDER ASSY., ROTARY HEAD, TLR-7 (SEE ILLUSTRATION 4 FOR BREAKDOWN)
QTY. 1 2 2 1 1 1 6 6 6 1
1 3 1 2 1
18 18 18 18 2 2 4 8 4 4 1
1
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
Page 7
E-TLR7-PL-0624
ILLUSTRATION 3: HANDWHEEL & LINKAGE GROUPING
Page 8
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
E-TLR7-PL-0624
PARTS LISTING – ILLUSTRATION 3: HANDWHEEL & LINKAGE GROUPING
ITEM # PART #
DESCRIPTION
1
65008
HANDWHEEL, SMALL W/ 5/8-8 X 18″ROD
2
10411
SCREW, SKT. HD. CAP 1/2-13 X 4 ZINC
3
50550
SLEEVE, BRASS 1/2″ TAPERED
4
14023
KNOB, BALL 1-3/8 W/ 1/2-13THD, BLK.
5
85005
BEARING, THRUST BALL 5/8
6
10073
WASHER, FLAT 5/8 SAE ZINC
7
68086
LINKAGE SUPPORT, UPPER CONTROL,TLR7
8
10440
COLLAR, LOCKING 7/8″ID
9
10096
COLLAR, LOCKING 5/8″ID
(NOTE: SET SCREW REMOVED AND CAPSCREW USED,
ITEM 25, FOR PRESSURE CONTROL LINKAGE ONLY.)
10
10784
CLAMP, HOSE, SAE #20, ADJ. TO 1-3/4
11
10930
BELLOWS 1-1/4ID X 2-3/8EL X 1-3/4RL
12
68043
LINKAGE, LOWER CONTROL 5/8-8 THD.
13
10808
FITTING, GREASE 1/4-28 STRAIGHT
14
68082
PIN, DETENT RING 1/2 X 4 E.L.
15
10359
SCREW, CAP 5/8-11 X 3-1/4 ZINC
16
79035
BUSHING, RUBBER 1-1/16 X 5/8 X 1/4
17
10127
SCREW, DRIVE 1/8 X 1/4″L
18
68083A
HANDWHEEL, LARGE W/ 5/8-11 INSERT
(THESE 2 PARTS ARE ASSEMBLED W/ RED LOCTITE)
19
68083
HANDWHEEL, LARGE W/ 7/8-9 THD.
(NOT FOR REPLACEMENT- SEE ITEM 18)
20
68084
THREAD INSERT 7/8-9 X 5/8-11
(NOT FOR REPLACEMENT- SEE ITEM 18)
21
10346
SCREW, SKT. HD. CAP 1/2-13 X 4-1/2
22
10104
KNOB, BALL 1-7/8 W/ 1/2-13THD, BLK.
23
11707
NUT, HEX NYLON LOCK 5/8-11 ZINC
24
10054
NUT, HEX 5/16-18 ZINC
25
10204
SCREW, CAP 5/16-18 X 1-3/4 ZINC
26
68085
LINKAGE, PRESSURE CONTROL 5/8-11
27
41041
SPRING, EXT. 1.75″OD X 8″L
QTY. 1 1 2 1 3 5 1 1 2
2 1 1 1 1 1 1 1 1
1
1
1 1 1 1 1 1 1
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
Page 9
E-TLR7-PL-0624
ITEM # 1
PART # 68068
2
68011
3
68065A
10126
4
68013
5
68001
6
68018
7
10370
8
10205
9
68067
10 26010 26020
11
68016
12
10445
PARTS LISTING – ILLUSTRATION 4 : ROTARY CUTTER HEAD ASSEMBLY
DESCRIPTION SPIDER ASSY., ROTARY HEAD, TLR-7 (INCLUDES ITEMS 2 THRU 8) SHAFT &
FLANGE, ROTARY, TLR-7 HUB ASSY. W/ SHAFTS, TLR-7 REPLACEMENT SPRING PINS:
PIN, H.D.COILED SPRING 5/16 X 1-1/2 FLANGE, ROTARY CUTTER HD BASE, TLR7
BUSHING, RUBBER 1-1/4 X 49/64 X 7/8 SLEEVE, RUBBER BUSHING, TLR-7 SCREW, CAP
1/2-20 X 3-1/4 (GRADE 8) NUT, HEX LOCK 1/2-20 ZINC FLANGE, ROTARY CUTTER
INNER, TLR-7 TR3 CUTTER ASSEMBLIES
TR3-24 SET OF 3 TRI-CUT CUTTERS (STANDARD) TR3-48 SET OF 3 TRI-CUT CUTTERS
FLANGE, ROTARY CUTTER OUTER, TLR-7 NUT, HEX JAM 7/8-9 LEFT-HAND THREAD
QTY. 1
1 1
3 1 6 3 3 3 3 1-SET
3 6
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
Page 11
E-TLR7-PL-0624
ILLUSTRATION 5: ENGINE & BELT DRIVE GROUPING
Page 12
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
E-TLR7-PL-0624
PARTS LISTING – ILLUSTRATION 5: ENGINE & BELT DRIVE GROUPING
ITEM # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
PART # 76005 40388 10830 100245 10832 10982 11572 – – – – 76024 77627 10450
11750 68033 68034 10225 68035 10056 10213 10801 10054 10606 10048 52015 10011
10064 75010 10251 15201A
50084 10831 10877 11567 11568 10970 36042
DESCRIPTION ENGINE, HONDA GXV390UT1DAXB CABLE, THROTTLE, LEVER-TYPE 24″ SCREW,
MACHINE PPH 10-32 X 1/2 THROTTLE BACKING PLATE, TLR-7 NUT, KEPS LOCK 10-32
ZINC TIE, CABLE, BLACK NYLON 12″ OIL DRAIN KIT, 11/13 HP HONDA VERT. KEY
(INCLUDED W/ ENGINE) CLUTCH, CENTRIFUGAL 3.5 X 2GR X 1 CLUTCH PLUG, 2GC-NG &
TLR-7 WASHER, LOCK 7/16 ZINC SCREW, CAP 7/16-20 X 2-3/4 ZINC MOUNT PLATE,
ENGINE, TLR-7 SPACER, ENGINE MOUNT, TLR-7 BUSHING, RUBBER, ENGINE MOUNT
TENSIONER, ENGINE TLR-7 BOLT, CARRIAGE 5/16-18 X 2 ZINC WASHER, FLAT 5/16 SAE
ZINC WASHER, LOCK 5/16 ZINC NUT, HEX 5/16-18 ZINC SCREW, CAP 5/16-18 X 1-1/4
ZINC SCREW, CAP 5/16-24 X 3/4 ZINC BOLT, TAP 3/8-16 X 3-1/2(FULL THD.) SPACER,
STEEL 5/8OD X 3/8ID X 3/8T BUSHING, SHEAVE SDS X 1-1/4″BORE SHEAVE 6.9″OD X
2GR.B X SDS BELT B-34 SWITCH W/ WIRES, ROCKER RED ON-OFF ADDITIONAL PARTS
REQ’D. (NOT SHOWN):
TERM., RING #10 16-14GA. INSULATED WASHER, LOCK, INT. TOOTH #10 SCREW, CAP
STSHW 10-24 X 1/2 CONNECTOR, BULLET STD. 16-14GA.BLUE CONNECTOR, LINE STD.
16-14GA.(BLUE) CONN., WIRE QUICK-SPLICE 18-14 GA. ADHESIVE CORD CLIP 5/8″SQ.
QTY. 1 1 2 1 2 1 1 1 1 1 1 1 1 2 4 1 2 6 8 10 2 2 1 1 1 1 2 1
1 1 1 1 1 1 3
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
Page 13
E-TLR7-PL-0624
THIS PAGE WAS LEFT BLANK INTENTIONALLY
Page 14
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
WIRING DIAGRAM
E-TLR7-PL-0624
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
Page 15
E-TLR7-PL-0624
ILLUSTRATION 6: KICK STAND ASSEMBLY
PART # 68036
Page 16
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
E-TLR7-PL-0624
PARTS LISTING – ILLUSTRATION 6 : KICK STAND ASSEMBLY
ITEM # PART #
DESCRIPTION
QTY.
1*
N/A
KICK STAND MNTG.BRKT.W/ OUTER TUBE
1
2*
N/A
KICK STAND DISENGAGEMENT PEDAL, TLR
1
3
10053
SCREW, CAP 5/16-18 X 3/4 ZINC
4
4
10213
WASHER, FLAT 5/16 SAE ZINC
10
5
10807
NUT, HEX LOCK 5/16-18 ZINC
4
6*
N/A
KICK STAND ENGAGEMENT PEDAL, TLR-7
1
7*
N/A
KICK STAND BASE W/ INNER TUBE, TLR
1
8
10382
SCREW, CAP 3/8-24 X 3-1/2 ZINC
1
9
10025
WASHER, FLAT 3/8 SAE ZINC
2
10
10011
SPACER, STEEL 5/8OD X 3/8ID X 3/8T
4
11
10058
NUT, HEX LOCK 3/8-24 W/ NYLON PATCH
1
12
68036S
SPRING, EXT., KICK STAND, TLR-7
1
13
10314
SCREW, CAP 1/4-20 X 1-3/4 ZINC
1
14
10015
NUT, HEX LOCK 1/4-20 ZINC
1
15
68007
RUBBER PAD, TLR-7 KICK STAND
1
(GLUED ON WITH CONTACT CEMENT)
*NOTE: THESE ITEMS ARE ONLY AVAILABLE WITH THE COMPLETE ASSEMBLY
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
Page 17
E-TLR7-PL-0624
DECAL SHEET P/N 92219
P/N 92219 Rev.C
Page 18
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
E-TLR7-PL-0624
LIMITED EQUIPMENT WARRANTY OF SALE
Equipment Development Company, Inc. herein referred to as EDCO (Seller)
warrants that each new unit manufactured by EDCO to be free from defects in
material and workmanship in normal use and service for a period of (1) one
year (except for the cutter drum assembly on all model concrete/asphalt
planers AND the chisel head assembly on all model ALR’s & ALR-BS in which case
the warranty period shall be 90 days) from date of shipment to the original
retail or equipment rental center owner.
Accessories or equipment furnished and installed on the product by EDCO but
manufactured by others, including, but not limited to engines,
motors,electrical components, transmissions etc., shall carry the accessory
manufacturers own warranty.
EDCO will, at its option, repair or replace, at the EDCO factory or at a point
designated by EDCO, any part which shall appear to the satisfaction of EDCO
inspection to have been defective in material or workmanship.
EDCO reserves the right to modify, alter and improve any part or parts without
incurring any obligation to replace any part or parts previously sold without
such modified, altered or improved part or parts.
This warranty is in lieu of and excludes all other warranties, expressed,
implied, statutory, or otherwise created under applicable law including, but
not limited to the warranty of merchantability and the warranty of fitness for
a particular purpose in no event shall seller or the manufacturer of the
product be liable for special, incidental, or consequential damages, including
loss of profits, whether or not caused by or resulting from the negligence of
seller and/or the manufacturer of the product unless specifically provided
herein. In addition, this warranty shall not apply to any products or portions
there of which have been subjected to abuse, misuse, improper installation,
maintenance, or operation, electrical failure or abnormal conditions and to
products which have been tampered with, altered, modified, repaired, reworked
by anyone not approved by seller or used in any manner inconsistent with the
provisions of the above or any instructions or specifications provided with or
for the product.
TERMS AND CONDITIONS
(NOT APPLICABLE TO SALES THROUGH AUTHORIZED DISTRIBUTION)
FORCE MAJEURE Seller’s obligation hereunder are subject to, and Seller shall
not be held responsible for, any delay or failure to make delivery of all or
any part of the Product due to labor difficulties, fires, casualties,
accidents, acts of the elements, acts of God, transportation difficulties,
delays by a common carrier, inability to obtain Product, materials or
components or qualified labor sufficient to timely perform part of or all of
the obligations contained in these terms and conditions, governmental
regulations or actions, strikes, damage to or destruction in whole or part of
manufacturing plant, riots, terrorist attacks or incidents, civil commotions,
warlike conditions, flood , tidal waves, typhoon, hurricane, earthquake,
lightning, explosion or any other causes, contingencies or circumstances
within or without the United States not subject to the Seller’s control which
prevent or hinder the manufacture or delivery of the Products or make the
fulfillment of these terms and conditions impracticable. In the event of the
occurrence of any of the foregoing, at the option of Seller, Seller shall be
excused from the performance under these Terms and Conditions, or the
performance of the Seller shall be correspondingly extended.
This document sets forth the terms and conditions pursuant to which the
purchaser (“Purchaser”) will purchase and Equipment Development Co.Inc.
(“Seller”)will sell the products, accessories, attachments (collectively the
Products “) ordered by the Purchaser. These terms and conditions shall govern
and apply to the sale of Seller’s Products to Purchaser, regardless of any
terms and conditions appearing on any purchase order or other forms submitted
by Purchaser to Seller, or the inconsistency of any terms therein and herein.
2. PAYMENT TERMS Payment terms are as follows. 2% 10 days (to approved and
qualified accounts). Net 30 days. This is a cash discount for invoices paid
within 10 days after the invoice date, regardless of date of receipt of
shipment. This is not a trade discount and will not be granted to accounts
that do not adhere to stated terms. All past due accounts are subject to a
late payment fee of 1.5% per month or a maximum allowed by law if different,
along with the expenses incidental to collection including reasonable
attorney’s fees and costs. Seller reserves the right to hold shipments
against past due accounts. *Seller reserves the right to alter payment terms.
3. FREIGHT TERMS All shipments will be made F.O.B. shipping point as
designated in these Terms and Conditions, and title shall pass at the F.O.B.
point. Delivery to the initial common carrier shall constitute delivery to the
Purchaser. Any claims for loss or damage during shipment are to be filed with
carrier by the Purchaser. Seller will not assume responsibility for the
performance of the carrier.
Back orders will be shipped in the most practical fashion with charges
consistent with our freight policy established with the original order. UPS,
FED EX, MAIL or shipments by other couriers are subject to the same terms and
conditions as outlined in paragraph #3″Freight Terms”.
4. DELIVERY, DAMAGES, SHORTAGES Seller shall use reasonable efforts to
attempt to cause the Products to be delivered as provided for in these Terms &
Conditions. Delivery to the initial common carrier shall constitute the
delivery to the Purchaser. Sellers responsibility, in so far as transportation
risks are concerned ceases upon the delivery of the Products in good condition
to such carrier at the F.O.B. point and all the Products shall be shipped at
the Purchaser’s risk. Seller shall not be responsible or liable for any loss
of income and/or profits, or incidental, special, consequential damages
resulting from Seller’s delayed performance in shipment and delivery.
5. RETURN OF DEFECTIVE PRODUCTS Defective or failed material shall be held at
the Purchaser’s premises until authorization has been granted by Seller to
return or dispose of Products. Products that are to be returned for final
inspection must be returned Freight Prepaid in the most economical way. Credit
will be issued for material found to be defective upon Seller’s inspection
based on prices at time of purchase.
6. PRODUCTS ORDERED IN ERROR Products may be returned, provided that claim is
made and Seller is notified within 7 days of receipt of Products, and the
Products are in original buyer’s possession not more than 30 days prior to
return, subject to Seller’s approval. If Products are accepted for return,
they must be Freight Prepaid and buyer will be charged a minimum of 15%
restocking charge, plus a charge back for outbound freight charges if the
original order was shipped prepaid. Returns are not accepted for any Products
that are specifically manufactured to meet the buyer’s requirement of either
specifications or quantity.
AGREEMENTS These Terms and Conditions constitute the entire agreement between
Seller and Purchaser as it relates to terms and conditions of sale, and
supersedes any and all prior oral or written agreements, correspondence,
quotations or understandings heretofore in force between the parties relating
to the subject matter hereof. There are no agreements between Seller and
Purchaser with respect to the Product herein except those specifically set
forth in and made part of these terms and conditions. Any additional terms,
conditions and/or prices are rejected by Seller.
1. PRICE All prices set forth on any purchase order or other document are F.O.B. Sellers facility or distribution point, as may be determined by Seller (F.O.B.Point). All prices are exclusive of any and all taxes, including, but not limited to, excise, sales, use, property or transportation taxes related to the sale or use of the Products, now or hereafter imposed, together with all penalties and expenses. Purchaser shall be responsible for collecting and/or paying any and all such taxes, whether or not they are stated in any invoice for the Products. Unless otherwise specified herein, all prices are exclusive of inland transportation, freight, insurance and other costs and expenses relating to the shipment of the Products from the F.O.B. point to Purchaser’s facility. Any prepayment by Seller of freight insurance and other costs shall be for the account
These terms and conditions may be modified, cancelled or rescinded only by a
written agreement of both parties executed by their duly authorized agents.
USE ONLY GENUINE EDCO PARTS & ACCESSORIES
For your own safety, the safety of others and the life of your machine.
SUBMIT ALL WARRANTY CLAIMS AT:
edcoinc.com/warranty-request-claim/
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
Page 19
E-TLR7-PL-0624
BEFORE USING THIS PRODUCT
Have You Used EDCO’s Online Customer Support??
Scan This QRC or Visit www.edcoinc.com/customer-support
READ: EDCO Owner’s Manuals and Parts Listings share basic information
and parts of each product. Download and print them whenever needed.
WATCH: EDCO Product Training Videos show how to use products, install
tooling, and perform basic maintenance.
Example Only
FIND: Somewhere on this product is an EDCO QRC Training Decal. Scanning
this code provides owner’s information, videos, and other training content
anywhere/anytime on your mobile device.
JOIN: EDCOed.com is a free, 24-hour training space. Each certification track
focuses on a specific EDCO product group. The information in these tracks help
businesses be successful with those products.
EDCO is always updating online training / information so you always have the
most recent content. Also see Operator’s Safety & Limited Warranty Manual
Equipment Development Co., Inc. · 800.638.3326 · techsupport@edcoinc.com
Page 20
800-638-3326 · edcoinc.com · techsupport@edcoinc.com
References
- Welcome To EDCOed – EDCO Experience Portal
- Welcome to EDCO, Inc.
- Warranty Request Claim - EDCO
- Welcome to EDCO, Inc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>