HOMEDEC HDC-HSTZ4BS-21-0331-01 Full Body Shower System with 6pcs Body Jets Spray Instruction Manual
- May 15, 2024
- HOMEDEC
Table of Contents
Concealed Thermostatic Shower System
Installation Manual
HDC-HSTZ4BS-21-0331-01 Full Body Shower System with 6pcs Body Jets
Spray
Please do not hesitate to contact us with your questions, concens and/or
problems,we’re here to help.
Customer Support:homedec-bath@foxmail.com IAPMO RESEARCH AND TESTING, INC.
5001 E. Philadelphia Street, Ontario, CA 91761 • Phone
909-472-4100 • Fax
909-472-4244 • www.iapmort.org
APMO Research and Testing, Inc. is
a product certification body in which its product certification system
includes nspection and testing of samples taken from the supplier’s stock or
from the market or a combination of both to verify compliance to the
requirements of applicable codes and standards. This activity is coupled with
periodic surveillance of the supplier’s factory and/or warehouses as well as
the assessment of the supplier’s Quality Assurance System. This listing is
subject to the conditions set forth in the characteristics below and is not to
be construed as any recommendation, assurance or guarantee by IAPMO Research
and Testing, Inc. of the product acceptance by Authorities Having
Jurisdiction.
Issued To:
KAIPING HUILIN SANITARY WARE CO., LTD.
BACK BLOCK, NO. 9,JIAXING SOUTH ROAD, SHUIKOU TOWN 529321 KAIPING, GUANGDONG,
CHINA
Product:
Plumbing Fixture Fittings
Products are in compliance with the following code(s):
Uniform Plumbing Code (UPC®}
National Plumbing Code of Canada
File Number: 13257
Effective Date: August 2022
Products are certified to the following standard(s):
ASME A112.18.1-2018/CSA 8125.1-18
Void After: August 2027 This certificate is not evidence
of current listing. To verify listing status, visit the IAPMO R&T Product
listing Directory at pld.lapmo.org
This listing period is based upon the last date of the month indicated on the
Effective Date and Void After Date shown above. Any change in material,
manufacturing process, marking or design without having first obtained the
approval of the Product Certification Committee. or any evidence of non-
compliance with applicable codes and standards or of inferior workmanship, may
be deemed sufficient cause for revocation of this listing. Production of or
reference to this form for advertising purposes may be made only by specific
written permission of IAPMO Research and Testing, Inc. Any alteration of this
certificate could be grounds for revocation of the listing. This document
shall be reproduced in its entirety.
Pipes Diagram Precautions before installation
Before installing the faucet, be sure to remove the debris and sludge in the
water pipe to prevent the debris from blocking the faucet and affecting the
normal water flow.
Installation Steps of Valve Body
29 | Accessory Bag | / | 1 |
---|---|---|---|
28 | 515304 Screw M5X6 | SCS304 | 2 |
27 | Thermostatic Valve Body | Brass(A) | 1 |
26 | Filter(Check Valve) | / | 2 |
25 | Thermostatic cartridge | / | 1 |
24 | Sleeve ring(2) | HPb59-2 | 1 |
23 | Socket Screw M5x18 | SUS304 | 1 |
22 | Handle Wheel | HPb59-2 | 1 |
21 | Spring | SUS304 | 1 |
20 | 0-ring | NBR | 7 |
19 | Faceplate | HPb59-2 | 1 |
18 | Plastic Hot Stop Circle | POM | 1 |
17 | Temperature Handle Cover | ZnA14 | 1 |
16 | Silicone plug | Silicone | 1 |
15 | Handle wheel | HPb59-2 | 4 |
14 | Socket Screw M5x5 | S1S304 | 5 |
13 | Diverter Handle | ZnA14 | 4 |
12 | Wear pad | PE | 4 |
11 | Diverter cartridge | / | 4 |
10 | Sleeve ring(1) | HPb59-2 | 4 |
9 | Base(1) | HPb59-2 | 1 |
8 | Stailess Steel Screw M5X10 | SUS304 | 18 |
7 | Connector | RFH59-2 | 4 |
6 | 0-Ring | NBR | 4 |
5 | 0-Ring | NBR | 16 |
4 | Connection Tube(2) | HPb59-2 | 4 |
3 | Base (2) | HPb59-2 | 3 |
2 | Connection Tube(1) | HPb59-2 | 1 |
1 | Base plate | S1S304 | 1 |
No. | Name | Material | Qty. |
- Release the top 6 handwheel levers (b) counter-clockwise by hand to take off the knobs. Next take out the hole plug (c) at the bottom of temperature handle, then use 2.5mm hex tool to release the screw (d) to take off hand cover.Remove and keep the black plastic circle (a) till the final finish of installation and temperature adjustment.
- Turn off the water supply.Determine pipe length and depth,Set up the waterlines properly based on the actual condition. the above digram for plumber reference(Must pay attention-letf is hot,right is cold)
- Drill 4 positioning holes for the valve body, The above digram for your reference.
- Hammer the 4 expansion screws into the holes.
- Fix the valve body with 4 positioning screws.
- Use copper sleeve wrench to tighten the screws.
- Connect the hot/cold inlets and outlets properly. Open the water supply to check and test, ensure there 1s no leakage or blockage at each connection.
- Temperature setting check. (DRotate the valve core clockwise or counterclockwise by hand to align the 2 marks on the valve core teeth (enlarged view A) ;(g)Attach the black gear ring on the valve core as picture directions (enlarged view B). ®Install the handle and plug as picture shows.
- Screw the handwheel into the handles.
Installation Steps of Body Jets
1).Attach the cover plate to body jets.| 2. Apply Teflon tape to threaded tail of the body jets| 3). Use a wrench to screw the jet heads clockwiseinto the body spray outlets.
Installation Steps of Hand Shower
1)、Wrap supply elbow threadwith Teflontape and attach cover plate to it.| 2). Screw the shower holder clockwise onto thehand shower outlet.| 3). Place rubber washers in both ends of the hose.Connect the shower hose to the supply elbow andshower head. Note the ends of shower hose to beconnected correctly.
Installation Steps of Waterfall Side Spray (Flexible mounting position)
1).Remove the threaded fitting by loosening the two fixing screws from the side.| 2). Apply Teflon tape to the end of the threads of the threaded fitting.
3).Screw the threaded fitting into thewall preview outlet hole.| 4).Insert the
body of the side spray into the threaded fitting and
retighten the two setscrews with a Allen wrench.
Installation Steps of Shower head
Parts List
NO. | Name | Qty. |
---|---|---|
1 | Bracket | 1 |
2 | M5*20 setscrew | 12 |
3 | Light Bar Fixing Tab | 4 |
4 | Light bar | 2 |
5 | Shower Panel | 1 |
6 | Touchscreen Controller (not included battery) | 1 |
7 | Power supply | 1 |
8 | expansion screw | 4 |
9 | 2.5mm Allen wrench | 1 |
10 | Water-inlet hose | 3 |
Installation Diagram!
1).Loosen the four M5*20 setscrew onthe shower panel with a 2.5mm Allenwrench.| 2).Separate the shower panel from the fixing bracket
3).Cutting holes in the ceiling with reference to the base dimensions of the product.| 4).Drill holes in the ceiling with reference to the base dimensions of the product.
5).Fit four expansion screws in thedrilled hole.| 6).Tighten and remove the nut with a spanner.
7).Attach the fixing bracket.| 8).Tighten the nuts of the expansion screws with a spanner.
9). Tighten the water-inlet hose to the reserved outlet on the wall.| 10).Holding the shower panel with our hand, connect the water-inlet
11).Connect the two light bar wires through the bracket to the wire tee| 12).Connect the other end of the wire tee connector to the power supply.
13).Fit the shower panel back into the bracket and secure it by tightening the four M5*20 setscrews with a Allen wrench.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>