EDCO BTWSG20 Wireless Earbuds and Charging Case Instructions
- June 12, 2024
- EDCO
Table of Contents
BTWSG20 UM
Power on/off:
- Power On: take out the earbuds from charging case, auto power on or long touching the multi-function until the led in blue.
- Power off: Put the earbuds back to charging case, auto power off and charging long, touching the multi-function until the led flashing in Red and lighting off
Pairing:
- Take out from charging case, earbuds auto paring, then search bluetooth match name”BTWSG20” on your Cell phone, and pair to the Cell phone.
- LED red blue light flash while pairing
- LED light off when pair to cell phone successfully.
Answer/refuse call
Answer call: short touch either earbud, touch again hang up call
refuse call: long touch 2 seconds either earbuds.
Play music:
- Short touch either earbud to pause
- Triple short touch “R” earbud to play next song, Triple short touch “L” earbud to play Previous song, Volume + to press R sides button 2 times,Volume – to press L sides button 2 times.
- Long touch 2 seconds on either earbud to wake voice assistant.
Charging:
- Put the earbuds to the charging case, auto charging.
- Inset the cable to Charge for the charging case, LED light on while charging, and light off , charging complete.
Earbuds and Charging Case Technical details:
Pairing Bluetooth name : BTWSG20
Bluetooth Version: 5.1
Wireless Support Protocol: A2DP,AVRCP,HSP,HFP
Earbud Battery capacity: 30mAh*2
Charging case Battery capacity: 230mAh
Charging time: 1-2 Hour
Charging Port: Type-C
Frequency:2.402-2.480GHZ
Play Time: 3 hours
Speaker: 32Ω
Standby Time: 120 hrs
Attention:
- Don’t crash, scratch, warping the earbuds, don’t throw to water.
- Keep away from the magnet, speaker when using the earbuds
- Avoid extreme temperature (working condition should be -100 ℃ -450 ℃)
- Avoid moist environment
Warning:
Don’t use the product while charging, use the original charger.
Li-polymer battery cannot be open and throw to fire, cannot connect with metal
or short circuit, cannot crash, avoid moist corrosion environment, avoid
heating condition( >60℃)
Package list
Bluetooth earbuds 1 pair
Charging case 1
instruction book 1
FCC warning:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference , and (2) this device must accept any interference received ,
including interference that may cause undesired operation .
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver .
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected .
- Consult the dealer or an experienced radio / TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
IC Warning:
This device complies with Innovation, Science and Economic Development Canada
licence-exempt RSS standard (s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
ISEDC Radiation Exposure Statement:
This equipment complies with ISEDC RF radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>