DS-18 Downcut Concrete and Asphalt Walk Behind Saw

Product Information

Specifications

• Model: DS-18
• Power Options:
  • Baldor Electric Motor 5HP 1PH 60Hz 230V
  • Baldor Electric Motor 5HP 3PH 60Hz 230V
  • Baldor Electric Motor 5HP 3PH 60Hz 460V
• SKU Numbers: 37300, 37400-230, 37400-460

Product Usage Instructions

Safety Information

Before operating the equipment, read and understand the
operator’s safety manual thoroughly. Ensure to keep body parts,
loose clothing, and accessories away from moving parts to prevent
accidents.

General Instructions

Maintain a safe operating distance from flammable materials to
prevent potential hazards caused by sparks. Always keep the
equipment away from flammable materials or vapors.

Dust Warning

Be cautious of dust accumulation during operation. Take
necessary precautions to prevent dust-related hazards.

Parts List Manual

How to Order Replacement Parts

When ordering replacement parts, always use genuine EDCO
replacement parts for product safety and reliability. Specify the
model and serial number of the machine along with the part number,
description, and quantity to your parts representative.

Illustration 1: Main Grouping

Below is a list of parts along with their respective part
numbers and descriptions:

FAQ

Q: Where can I find the operator’s safety manual?

A: The operator’s safety manual can be accessed at
edcoinc.com/customer-support/parts-and-manuals.

Q: How should I order replacement parts?

A: When ordering replacement parts, specify the model and serial
number of the machine, along with the part number, description, and
quantity to your parts representative.

PARTS LIST MANUAL
MODEL DS-18

E-DS18-PL-0324
REVISED STARTING SERIAL # 240310165

ELECTRIC MODEL

18″ DOWNCUT – CONCRETE AND ASPHALT WALK BEHIND SAWS

SKU # 37300 37400-230 37400-460

MODEL DS-18 DS-18 DS-18

POWER OPTION BALDOR ELECTRIC MOTOR 5HP 1PH 60Hz 230V BALDOR ELECTRIC MOTOR 5HP 3PH 60Hz 230V BALDOR ELECTRIC MOTOR 5HP 3PH 60Hz 460V

READ AND UNDERSTAND THE OPERATOR’S SAFETY MANUAL THOROUGHLY BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT.
Death or serious injury could occur if this machine is used improperly. Machine specific Operator’s Instruction Manuals are offered at edcoinc.com /customer-support/parts-and-manuals

EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
8P0h0o-n6e3:W88-e03b03s- 26it63e8:·-w3ew3d2wc6.oeodinrc3co0i.nc1co-.6cm6o3m·-1t6e· 0cE0h- sm·uaFpila:pxtoe: cr8ht0@s0u-ep4dp4o7cr-ot3@i3n2ec6d.ccooorimn3c0.1c- o6m63-1607

Printed in USA JWA ©2024
Page 1

E-DS18-PL-0324

SAFETY INFORMATION

SAFETY MESSAGES
· Safety Instructions are proceeded by a graphic alert symbol of DANGER, WARNING, or CAUTION.
Indicates an imminent hazard which, if not avoided, will result in death or serious injury.
Indicates an imminent hazard which, if not avoided, can result in death or serious injury.
Indicates hazards which, if not avoided, could result in serious injury and or damage to the equipment.

ELECTRICAL POWERED EQUIPMENT CONTINUED
· Do not disconnect power by pulling cord. To disconnect, grasp the plug, not the cord.
· Unplug power cord at the machine when not in use and before servicing.
· Switch motor OFF before disconnecting power. · Never use frayed, damaged, taped or under rated extension cords.
Electrical shock could result in death or serious injury to the operator and damage to the equipment. · Assure you are using the proper extension cord length.

GASOLINE / PROPANE POWERED EQUIPMENT
· Engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. · Tilting a gasoline powered machine fitted with an EPA approved vented charcoal filter gas cap, beyond 20° can cause fuel leakage. If a leak occurs, do not start or run the engine until the leak is fixed. Eliminate all other ignition sources in the immediate area (no smoking, flares, sparks or flames). Use approved gasoline absorbing material to contain the fuel leakage. Then use clean, non-sparking tools to collect absorbed materials then dispose of these contaminants properly. · Gasoline is extremely flammable and poisonous. It should only be dispensed in well ventilated areas, and with a cool engine. · Small gasoline engines produce high concentrations of carbon monoxide (CO) example: a 5 HP 4 cycle engine operation in an enclosed 100,000 cu. ft. area with only one change of air per hour is capable of providing deadly concentrations of CO in less than fifteen minutes. Five changes of air in the same area will produce noxious fumes in less than 30 minutes. Gasoline powered equipment should not be used in enclosed or partially enclosed areas. Symptoms of CO poisoning include, head-ache, nausea, weakness, dizziness, visual problems and loss of consciousness. If symptoms occur – get into fresh air and seek medical attention immediately. · Never refuel a hot engine or an engine while it is running. · Engines are shipped from factory without fuel/oil. · Propane is extremely flammable and is heavier than air and tends to settle in low areas where a spark or flame could ignite gas. DO NOT start or operate this propane engine in a poorly ventilated area where leaking propane gas could accumulate and endanger safety of persons in area. If headache develops, shut off machine. Have it checked for carbon monoxide emissions by a qualified technician before using it again. To ensure personal safety, installation and repair of propane fuel supply systems must be performed only by qualified technicians. Carbon monoxide emissions from this machine are greatly increased due to a dirty combustion air cleaner.
ELECTRICAL POWERED EQUIPMENT
Extreme care must be taken when operating electric models with water present: Ensure power cord is properly grounded, is attached to a Ground-Fault- Interrupter (GFI) outlet, and is undamaged. · Check all electrical cables – be sure connections are tight and cable is continuous and in good condition. Be sure cable is correctly rated for both the operating current and voltage of this equipment. · Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with qualified electrician or service person if there is any doubt as to whether the outlet is properly grounded. Adhere to all local codes and ordinances. · NOTE: In the event of a malfunction or breakdown, grounding provides a path of least resistance for the electric current to dissipate. The motor is equipped with a grounded plug and must be connected to an outlet that is properly installed and properly grounded. DO NOT modify the plug provided on the motor. If the plug does not fit the outlet have a qualified electrician install the proper receptacle.

GENERAL INSTRUCTIONS
· Equipment should only be operated by trained personnel in good physical condition and mental health (not fatigued). The operator and maintenance personnel must be physically able to handle the bulk weight and power of this equipment.
· This is a one person tool. Maintain a safe operating distance to other personnel. It is the operators’ responsibility to keep other people (workers, pedestrians, bystanders, etc.) away during operation. Block off the work area in all directions with roping, safety netting, etc. Failure to do so may result in others being injured by flying debris or exposing them to harmful dust and noise.
· This equipment is intended for commercial use only. · For the operator’s safety and the safety of others, always keep all
guards in place during operation. · Never let equipment run unattended.
· Personal Protection Equipment and proper safety attire must be worn when operating this machinery. The operator must wear approved safety equipment appropriate for the job such as hard hat and safety shoes when conditions require. Hearing protection MUST be used when operational noise levels of this equipment may exceed 85db. Eye protection MUST be worn at all times.
Keep body parts, loose clothing and accessories away from moving parts. Failure to do so could result in dismemberment or death.
· Do not modify the machine. · Stop motor/engine when adjusting or servicing this equipment. Maintain
a safe operating distance from flammable materials. Sparks from the cutting- action of this machine can ignite flammable materials or vapors.
DUST WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects, or other reproductive harm. Materials being removed can be toxic or hazardous. A breathing respirator is required to help protect the operator. Some examples of these chemicals are: · Lead from lead-based paints. · Crystalline silica from bricks, concrete and other masonry products.Your risk of exposure to these chemi cals varies depending on how often you do this type of work. To reduce your risk: work in a well ventilated area, use a dust control system, such as an industrialstyle vacuum, and wear approved personal safety equipment, such as a dust/particle respirator designed to filter out microscopic particles. · See more on the importance of dust prevention and silica warnings at: osha.gov/silica · More concrete and silica dust supression training and educational materials available at edcoinc.com/silica-standards or scan the QR code on page 5. · Written exposure plans are provided at http://www.edcoinc.com/writtenexposure-control-plans/

Page 2

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

E-DS18-PL-0324

PARTS LIST MANUAL
MODEL DS-18
18″ DOWNCUT – CONCRETE AND ASPHALT WALK BEHIND SAW

TABLE OF CONTENTS

Section

Page Number

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 How To Order Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Illustration 1: Main Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 5 Illustration 2: Arbor & Blade Guard Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 7 Illustration 3: Optional Water Tank Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 9 Illustration 4: Single Phase Motor Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 11 Wiring Diagram for Rotary Cam Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Wiring Diagram for 1 Phase Motor – Baldor L3608TM . . . . . . . . . . . . . . . . . . . . . 13 Illustration 5: Three Phase Motor Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 15 Illustration 6: Swich Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Illustration 7: Advance Controls Inc. (aci) Brand Reset Starter Assembly . . . . . . . 17 Wiring Diagram for Starter & Remote Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Wiring Diagram for 3 Phase 60Hz Motor – Baldor EM3613T . . . . . . . . . . . . . . . . . 19 Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20, 21 Limited Equipment Warranty of Sale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 STOP – Before Using This Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

HOW TO ORDER REPLACEMENT PARTS
To insure product safety and reliability, always use genuine EDCO replacement parts when making repairs to the equipment.
When calling for parts, specify the MODEL and SERIAL number of the machine, which can be found on the NAME PLATE. Keep that information in the space provided. In addition to this information, give part number, description, and quantity as listed on the parts list to your parts representative.
Please note: Due to improvements and changes in the equipment, the illustrations shown may be different than the actual machine.

FILL IN INFORMATION BELOW Date of Purchase __ Model # _____ Serial # __ SKU #

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 3

E-DS18-PL-0324

ILLUSTRATION 1: MAIN GROUPING

Page 4

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

E-DS18-PL-0324

ITEM
1 2 3

PART #
56301 10009 79013

4 11597

5 10306 6 56302 7 11597
10009 8 52001

9 10306 10 65239 11 10312 12 10155 13 10347 14 10154 15 56204 16 10808 17 56303 18 10317 19 10025 20 10156 21 10608 22 51075

23 14023 24 50550 25 10346 26 80009

PARTS LISTING – ILLUSTRATION 1: MAIN GROUPING

DESCRIPTION

QTY.

MAIN FRAME, DS-18

1

WASHER, FLAT 3/4 SAE ZINC

2

WHEEL, 8 X 2-1/2 X 3/4″BRG.

2

POLY HUB

WASHER .755″ID X 1.25″OD X

2

.060″THK

PIN, COTTER 3/16 X 1-1/2

2

FORK, DS-18/20

1

WASHER .755″IDx1.25″ODx.060″THK AS

WASHER, FLAT 3/4 SAE ZINC

R’D.

WHEEL 4 X 1-1/2 X 3/4″BRG.

2

ALUM/RUB

PIN, COTTER 3/16 X 1-1/2

2

SCREW, CAP 1/2-13 X 10

1

WASHER, FLAT 1/2 SAE ZINC

2

NUT, HEX NYLON LOCK 1/2-13 1

SCREW, CAP 1/2-20 X 2-1/4

1

NUT, HEX NYLON LOCK 1/2-20 1

LINKAGE, CUT CONTROL

1

FITTING, GREASE 1/4-28 STR. 1

HANDLE BAR, DS-18

1

SCREW, CAP 3/8-16 X 2

4

WASHER, FLAT 3/8 SAE ZINC

8

NUT, HEX NYLON LOCK 3/8-16 4

GRIP, HAND 1″ MODEL AT

2

HANDWHEEL, LARGE W/ 5/8-8 X 1 13″ROD

KNOB, BALL 1-3/8 W/ 1/2-13THD 1

SLEEVE, BRASS 1/2″ TAPERED 1

SCREW, SHC 1/2-13 X 4-1/2

1

BEARING, BALL 5/8″ 2-HOLE

1

(NO G.F.)

ITEM
27 28 29 30

PART #
10412 10602 10150 55010

31 10096 32 56206 33 10907 34 10811 35 10025 36 56305 37 10837 38 10312 39 10155 40 10055 41 10025 42 10811 43 10156 44 56304 45 51012 46 50024 47 10025 48 10156 49 51078

50 56221 51 10499 52 10155

DESCRIPTION

QTY.

BOLT, CARRIAGE 1/4-20 X 1

2

WASHER, FLAT 1/4 SAE ZINC

2

NUT, HEX NYLON LOCK 1/4-20 2

SPACER, HANDWHEEL

1

5/8″ID X 3/4″L

COLLAR, LOCKING 5/8″ID

1

COVER, BELT, DS-18/20

1

SCREW, CAP 3/8-16 X 3/4

2

WASHER, LOCK 3/8 ZINC

2

WASHER, FLAT 3/8 SAE ZINC

2

LIFTING BAIL, DS-18

1

BOLT, EYE 1/2-13 X 1-1/2

1

WASHER, FLAT 1/2 SAE ZINC

1

NUT, HEX NYLON LOCK 1/2-13 1

SCREW, CAP 3/8-16 X 1

3

WASHER, FLAT 3/8 SAE ZINC

3

WASHER, LOCK 3/8 ZINC

3

NUT, HEX NYLON LOCK 3/8-16 3

GUIDE BAR, DS18/20 SS20/24

1

GUIDE POINTER, FRONT 14-1/2″ 1

WHEEL 4 X 1-3/8 X 3/8″BORE

1

WASHER, FLAT 3/8 SAE ZINC

2

NUT, HEX NYLON LOCK 3/8-16 1

PLUG, SQ. TUBE 1 X 14 GA.,

1

BLACK

ROPE, GUIDE BAR, DS-18/20

1

SCREW, CAP 1/2-13 X 3

1

NUT, HEX NYLON LOCK 1/2-13 1

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 5

E-DS18-PL-0324
ILLUSTRATION 2: ARBOR & BLADE GUARD GROUPING

Page 6

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

E-DS18-PL-0324

PARTS LISTING – ILLUSTRATION 2: ARBOR & BLADE GUARD GROUPING

ITEM # PART #

DESCRIPTION

QTY.

1

56320A

ARBOR ASSY. COMPLETE, DS-18

1

(INCLUDES ITEMS 2 THRU 12)

2

56208

ARBOR SHAFT 23-3/8″L

1

3

50222

BEARING, BALL 1″ TPB

2

4

10071

KEY 1/4SQ X 2-1/2

1

5

56235

SHEAVE 3.35″OD X 3GR.3V X 1″BORE

1

6

56308

ARBOR BACKING PLATE 4-1/2″, DS-18

2

7

10211

PIN, ROLL 5/16 X 2

2

8

56309

ARBOR BLADE CAP 4-1/2″, DS-18

1

(INCLUDES SHEAR PROOF PIN, ITEM 9)

9

10129

PIN, SHEAR PROOF 3/8 X 1-1/4

1

10

55009

WASHER, LOCK, INT. TOOTH 1″

2

11

50019

NUT, HEX JAM 1-14 ZINC GRADE A

2

12

10427

COLLAR, LOCKING 1″ID

1

13

10907

SCREW, CAP 3/8-16 X 3/4

4

14

10811

WASHER, LOCK 3/8 ZINC

4

15

50445

WRENCH, ARBOR, 1-1/2″ OPEN END

2

16

56306C

GUARD, BLADE 18″, ASSY. COMP. DS18

1

(INCLUDES ITEM 17, 18, & 19)

17

56306

BLADE GUARD 18″, DS-18

1

18

81004

NOZZLE, COOLANT 1/8MPT W/ 4″TUBES

1

19

11562

BARB ELBOW 90, 3/8HOSE X 1/8MPT

1

20

10386

SCREW, CAP 1/2-13 X 4-1/2

1

21

10045

WASHER, LOCK 1/2 ZINC

1

22

10907

SCREW, CAP 3/8-16 X 3/4

1

23

10811

WASHER, LOCK 3/8 ZINC

1

24

10025

WASHER, FLAT 3/8 SAE ZINC

1

25

10714

CLAMP, HOSE, SAE #4, ADJ. TO 5/8″

2

26

51318

HOSE, WATER 3/8″ID X 50″L, DS-18

1

27

11565

CLAMP, LOOM, 5/8″ (SAE SIZE 10)

1

28

10038

WASHER, LOCK 1/4 ZINC

1

29

10846

SCREW, CAP STSHW 1/4-20 X 5/8

1

30

10982

TIE, CABLE, BLACK NYLON 12″

2

31

56022

BRACKET, WATER VALVE

1

32

10711A

VALVE & HOSE CONNECTOR ASSY.

1

33

10799

BARB ELBOW 90, 3/8HOSE X 1/4MPT

1

34

10846

SCREW, CAP STSHW 1/4-20 X 5/8

2

35

10038

WASHER, LOCK 1/4 ZINC

2

36

56307

COVER, ARBOR, DS-18

1

37

10025

WASHER, FLAT 3/8 SAE ZINC

1

38

10811

WASHER, LOCK 3/8 ZINC

1

39

10907

SCREW, CAP 3/8-16 X 3/4

1

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 7

E-DS18-PL-0324
ILLUSTRATION 3: OPTIONAL WATER TANK ASSEMBLY
PART # 56310

Page 8

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

E-DS18-PL-0324

ITEM # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

PARTS LISTING – ILLUSTRATION 3: OPTIONAL WATER TANK ASSEMBLY
PART #56310

PART # 52031 56311 10412 10602 10861 52035 10905 10602 10150 52034 56312 10714 56315 11637 56316

DESCRIPTION DRUM, PLASTIC 5 GALLON, 3/4NPT CAP TRAY, WATER TANK, DS-18 BOLT, CARRIAGE 1/4-20 X 1 WASHER, FLAT 1/4 SAE ZINC NUT, KEPS LOCK 1/4-20 ZINC TIE- DOWN STRAP, MOLDED RUBBER 24″ SCREW, CAP 1/4-20 X 1-1/4 WASHER, FLAT 1/4 SAE ZINC NUT, HEX NYLON LOCK 1/4-20 ZINC BUSHING, HEX 3/4 X 1/4 NPT NYLON VALVE, BALL PVC 90°A 1/4MPT X BARB CLAMP, HOSE, SAE #4, ADJ. TO 5/8″ HOSE, WATER 3/8″ID X 24″L COUPLING, QUICK-DISCONNECT 3/8″ SPL HOSE, WATER 3/8″ID X 2″L

QTY. 1 1 2 2 2 2 2 2 2 1 1 4 1 1 1

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 9

E-DS18-PL-0324
ILLUSTRATION 4: SINGLE PHASE MOTOR GROUPING

Page 10

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

E-DS18-PL-0324

PARTS LISTING – ILLUSTRATION 4: SINGLE PHASE MOTOR GROUPING

ITEM # 1
2 3 4 5 6 7 8 9 10
11 12
13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

PART # 81026
16121 16164 16540 10740 16539 56318 11565 10831 10877 41130 77043-1 77043
77043-2 77043-4 77042 11663
10462 10846 10038 101290 15204 56313 10321 10312 10154 10802 10025 10811 10404 51067 10417 10819 10213 10801 10054 10071 56314 10269

DESCRIPTION MOTOR, BALDOR 5HP-1PH 60HZ 3450RPM L3608TM
REPLACEMENT PARTS: CAPACITOR, START, EC1161C06, 161-193MFD, 250V CAPACITOR, RUN, OC3040F09SP, 40MFD, 370V RESET BUTTON, BALDOR TPBRT25DB CONDUIT LOCK NUT 3/4 NP (INSIDE JUNCTION BOX) STRAIN RELIEF 90D X 3/4NPT .50-.625 WIRE HARNESS 10/3 X 54″LOA, DS18 CLAMP, LOOM, 5/8″ (SAE SIZE 10) WASHER, LOCK, INT. TOOTH

10 SCREW, CAP STSHW 10-24 X 1/2 STRAIN RELIEF 1/2NPT X .550-.650″ SWITCH

ADAPTER, PG16 TO 1/2″NPT SWITCH, ROTARY CAM ON/OFF REPLACEMENT PARTS: SWITCH HANDLE, PADLOCKABLE, LOVATO GASKET RING, OPERATOR, LOVATO BRACKET, ROTARY CAM SWITCH SCREW, MACHINE 8-32 X 1/2 RHCD ZINC (INSIDE SWITCH BOX) NUT, KEPS LOCK 8-32 ZINC SCREW, CAP STSHW 1/4-20 X 1/2 WASHER, LOCK 1/4 ZINC CORD 10/3 W/ PLUG, 50FT. 30A/250V PLUG, RECT. HOLE, PLASTIC SNAP-IN MOUNT, MOTOR, DS-18 SCREW, CAP 1/2-20 X 1-1/4 WASHER, FLAT 1/2 SAE ZINC NUT, HEX NYLON LOCK 1/2-20 ZINC BOLT, CARRIAGE 3/8-16 X 1 ZINC WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-16 ZINC
BOLT, TAP 1/2-13 X 7, GRADE 5
NUT, HEX 1/2-13 ZINC BOLT, CARRIAGE 5/16-18 X 1
WASHER, FLAT 5/16 SAE ZINC
WASHER, LOCK 5/16 ZINC
NUT, HEX 5/16-18 ZINC
KEY 1/4SQ X 2-1/2
SHEAVE 2.8″OD X 3GR.3V X 1-1/8″BORE
BELT 3VX-400

QTY. 1
2 1 1 1 1 1 4 3 3 2 2 1
1 1 1 4
4 2 2 1 1 1 2 2 2 2 2 2 2 2 2 4 4 4 4 1 1 3

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 11

E-DS18-PL-0324

SINGLE PHASE MODEL

WIRING DIAGRAM FOR ROTARY CAM SWITCH

60HZ 1-PHASE 230V

LEFT

FRONT

RIGHT

4

3

4

3

1

2

1

2

MOTOR POWER CORD CORD

Page 12

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

SINGLE PHASE MODEL

E-DS18-PL-0324

WIRING DIAGRAM FOR 1 PHASE MOTOR BALDOR L3608TM
USE CONNECTIONS FOR OPPOSITE (OPP) ROTATION SHOWN BELOW IN CHART

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 13

E-DS18-PL-0324
ILLUSTRATION 5: THREE PHASE MOTOR GROUPING

Page 14

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

E-DS18-PL-0324

PARTS LISTING – ILLUSTRATION 5: THREE PHASE MOTOR GROUPING

ITEM # 1 2
3 4
5 6 7 8 9 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

PART #

DESCRIPTION

QTY.

81022

MOTOR, BALDOR 5HP-3PH-60HZ-230/460V EM3613T

16604 16458

STARTER, ACI RESET ONLY (SEE ILLUS. 6 FOR REPLACEMENT PARTS) STARTER ACI

128844 200/240V COIL 11.3-16A O/L STARTER ACI #128846 440/480V COIL 5.5-7.5A

O/L

65087

MOUNT, STARTER, CPM-8/10 DS-18

11732 10384

SCREW, MACHINE 10-32 X 1-3/4 RHP SCREW, MACHINE 10-32 X 1 RHP

10832

NUT, KEPS LOCK 10-32 ZINC

11621

STRAIN RELIEF 90D X 1/2NPT .625-.75

10984

STRAIN RELIEF 90D X 3/4NPT .625-.75

10740

CONDUIT LOCK NUT 3/4 NP

65108

WIRE HARNESS 10/4 X 34″LOA

65105

WIRE HARNESS 10/4 X 50″LOA

65140

WIRE HARNESS 16/2 X 48″LOA

16190

STRAIN RELIEF 1/2NPT X .250-.350″

10790

CONDUIT LOCK NUT 1/2 NP

41053

STRAIN RELIEF 1/2NPT X .625-.750″

16660

SWITCH BOX COMPLETE, ON/OFF/E-STOP (SEE ILLUS. 5 FOR REPLACEMENT PARTS)

65122

BRACKET, REMOTE SWITCH

11663

SCREW, MACHINE 8-32 X 1/2 RHCD (LOCATED INSIDE BOX)

10462

NUT, KEPS LOCK 8-32 ZINC

11565

CLAMP, LOOM, 5/8″ (SAE SIZE 10)

10846

SCREW, CAP STSHW 1/4-20 X 1/2

10038

WASHER, LOCK 1/4 ZINC

10982

TIE, CABLE, BLACK NYLON 12″

15204

PLUG, RECT. HOLE, PLASTIC SNAP-IN

56313

MOUNT, MOTOR, DS-18

10321

SCREW, CAP 1/2-20 X 1-1/4

10312

WASHER, FLAT 1/2 SAE ZINC

10154

NUT, HEX NYLON LOCK 1/2-20 ZINC

10802

BOLT, CARRIAGE 3/8-16 X 1 ZINC

10025

WASHER, FLAT 3/8 SAE ZINC

10811

WASHER, LOCK 3/8 ZINC

10404

NUT, HEX 3/8-16 ZINC

51067

BOLT, TAP 1/2-13 X 7, GRADE 5

10417

NUT, HEX 1/2-13 ZINC

10820

BOLT, CARRIAGE 5/16-18 X 1-1/4 F.T.

10213

WASHER, FLAT 5/16 SAE ZINC

10801

WASHER, LOCK 5/16 ZINC

10054

NUT, HEX 5/16-18 ZINC

10071

KEY 1/4SQ X 2-1/2

56314

SHEAVE 2.8″OD X 3GR.3V X 1-1/8″BORE

10269 800-638B-3E3L2T63·VeXd-c4o0i0nc.com · techsupport@edcoinc.com

1 1 1 2 1 3 1 1 1 1 1 1 2 1 1 1
1 4 4 1 2 2 4 1 1 2 2 2 2 2 2 2 2 2 4 4 4 4 1 1 3
Page 15

E-DS18-PL-0324

THREE PHASE MODELS
ILLUSTRATION 6: SWITCH ASSEMBLY P/N 16660
REPLACEMENT PARTS

ITEM # 1

PART # 16660

2

16661

3

16662

4

16663

5

16664

6

16665

7

16666

DESCRIPTION SWITCH BOX COMPLETE, ON/OFF/E-STOP (INCLUDES ITEMS 2 THRU 7) ENCLOSURE, 2 HOLE ACI PBE2 LEGEND PLATE, EMER.STOP LEGEND PLATE, OFF/ON MUSHROOM BUTTON, RED, 1NO+1NC CONT. (INCLUDES CONTACT BLOCK) KNOB TYPE SELECTOR SWITCH, BLACK (INCLUDES CONTACT BLOCK) WIRE, BLACK JUMPER 14 AWG X 3″

QTY. 1
1 1 1 1
1
1

Page 16

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

THREE PHASE MODELS
ILLUSTRATION 7: ADVANCE CONTROLS, INC. (aci) BRAND
RESET STARTER ASSEMBLY
P/N 16604 &16458
REPLACEMENT PARTS

E-DS18-PL-0324

SET AMPS HERE

ITEM # 1 2 3
4
5

PART # 16653 16655
16617 16618
16622 16623
16635 16632

DESCRIPTION
STARTER BOX ONLY, RESET (INCLUDES ITEM 2)
STOP/RESET PUSHBUTTON ASSY., RED
CONTACTOR WITH COIL (INLUDES ITEM 4): STARTER CONT./COIL ACI SK18.310-230 (230V) STARTER CONT./COIL ACI SK18.310-460 (460V)
STARTER AC COIL ONLY: AC COIL 200/240V-60HZ (230V) AC COIL 440/480V-60HZ (460V)
STARTER OVERLOAD RELAY: O/L RELAY 10.3-16.0 AMP (230V – SET AMPS @13 ) O/L RELAY 5.5 – 7.5 AMP (460V – SET AMPS @ 7)

QTY. 1 1 1
1
1

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 17

E-DS18-PL-0324

THREE PHASE MODELS

WIRING DIAGRAM FOR STARTER & REMOTE SWITCH
60HZ 3-PHASE

Page 18

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

THREE PHASE MODELS

E-DS18-PL-0324

WIRING DIAGRAM FOR 3 PHASE 60Hz MOTOR BALDOR EM3613T

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 19

E-DS18-PL-0324

DECAL SHEET

Page 20

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

START

ROTATION
RESET

ROTATION
Voltage Decals 8.5 x 11 P/N 92207

STOP
RESET

DECALS CONTINUED
230 VOLTS SINGLE PHASE
460 VOLTS
O N THREE PHASE
Electric-1 4 x 7 P/N 92206 Rev. A

E-DS18-PL-0324

110 VOLTS

220 VOLTS

380 VOLTS

415 VOLTS

440 VOLTS

460 VOLTS

480 VOLTS

575 VOLTS

THREE PHASE

GROUND

GROUND

GROUND

GROUND

OFF

NOTE: Locate this decal so it is visible, close to and pointing at the MANUAL RESET
button located on the motor

NOTE: Locate this decal so it is visible, close to and pointing at the MANUAL RESET
button located on starter box
800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 21

E-DS18-PL-0324
THIS PAGE LEFT BLANK INTENTIONALLY

Page 22

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

E-DS18-PL-0324

LIMITED EQUIPMENT WARRANTY OF SALE

Equipment Development Company, Inc. herein referred to as EDCO (Seller) warrants that each new unit manufactured by EDCO to be free from defects in material and workmanship in normal use and service for a period of (1) one year (except for the cutter drum assembly on all model concrete/asphalt planers AND the chisel head assembly on all model ALR’s & ALR-BS in which case the warranty period shall be 90 days) from date of shipment to the original retail or equipment rental center owner.
Accessories or equipment furnished and installed on the product by EDCO but manufactured by others, including, but not limited to engines, motors,electrical components, transmissions etc., shall carry the accessory manufacturers own warranty.
EDCO will, at its option, repair or replace, at the EDCO factory or at a point designated by EDCO, any part which shall appear to the satisfaction of EDCO inspection to have been defective in material or workmanship.
EDCO reserves the right to modify, alter and improve any part or parts without incurring any obligation to replace any part or parts previously sold without such modified, altered or improved part or parts.
This warranty is in lieu of and excludes all other warranties, expressed, implied, statutory, or otherwise created under applicable law including, but not limited to the warranty of merchantability and the warranty of fitness for a particular purpose in no event shall seller or the manufacturer of the product be liable for special, incidental, or consequential damages, including loss of profits, whether or not caused by or resulting from the negligence of seller and/or the manufacturer of the product unless specifically provided herein. In addition, this warranty shall not apply to any products or portions there of which have been subjected to abuse, misuse, improper installation, maintenance, or operation, electrical failure or abnormal conditions and to products which have been tampered with, altered, modified, repaired, reworked by anyone not approved by seller or used in any manner inconsistent with the provisions of the above or any instructions or specifications provided with or for the product.
TERMS AND CONDITIONS
(NOT APPLICABLE TO SALES THROUGH AUTHORIZED DISTRIBUTION)
FORCE MAJEURE Seller’s obligation hereunder are subject to, and Seller shall not be held responsible for, any delay or failure to make delivery of all or any part of the Product due to labor difficulties, fires, casualties, accidents, acts of the elements, acts of God, transportation difficulties, delays by a common carrier, inability to obtain Product, materials or components or qualified labor sufficient to timely perform part of or all of the obligations contained in these terms and conditions, governmental regulations or actions, strikes, damage to or destruction in whole or part of manufacturing plant, riots, terrorist attacks or incidents, civil commotions, warlike conditions, flood , tidal waves, typhoon, hurricane, earthquake, lightning, explosion or any other causes, contingencies or circumstances within or without the United States not subject to the Seller’s control which prevent or hinder the manufacture or delivery of the Products or make the fulfillment of these terms and conditions impracticable. In the event of the occurrence of any of the foregoing, at the option of Seller, Seller shall be excused from the performance under these Terms and Conditions, or the performance of the Seller shall be correspondingly extended.
This document sets forth the terms and conditions pursuant to which the purchaser (“Purchaser”) will purchase and Equipment Development Co.Inc. (“Seller”)will sell the products, accessories, attachments (collectively the Products “) ordered by the Purchaser. These terms and conditions shall govern and apply to the sale of Seller’s Products to Purchaser, regardless of any terms and conditions appearing on any purchase order or other forms submitted by Purchaser to Seller, or the inconsistency of any terms therein and herein.

2. PAYMENT TERMS Payment terms are as follows. 2% 10 days (to approved and qualified accounts). Net 30 days. This is a cash discount for invoices paid within 10 days after the invoice date, regardless of date of receipt of shipment. This is not a trade discount and will not be granted to accounts that do not adhere to stated terms. All past due accounts are subject to a late payment fee of 1.5% per month or a maximum allowed by law if different, along with the expenses incidental to collection including reasonable attorney’s fees and costs. Seller reserves the right to hold shipments against past due accounts. *Seller reserves the right to alter payment terms.
3. FREIGHT TERMS All shipments will be made F.O.B. shipping point as designated in these Terms and Conditions, and title shall pass at the F.O.B. point. Delivery to the initial common carrier shall constitute delivery to the Purchaser. Any claims for loss or damage during shipment are to be filed with carrier by the Purchaser. Seller will not assume responsibility for the performance of the carrier.
Back orders will be shipped in the most practical fashion with charges consistent with our freight policy established with the original order. UPS, FED EX, MAIL or shipments by other couriers are subject to the same terms and conditions as outlined in paragraph #3″Freight Terms”.
4. DELIVERY, DAMAGES, SHORTAGES Seller shall use reasonable efforts to attempt to cause the Products to be delivered as provided for in these Terms & Conditions. Delivery to the initial common carrier shall constitute the delivery to the Purchaser. Sellers responsibility, in so far as transportation risks are concerned ceases upon the delivery of the Products in good condition to such carrier at the F.O.B. point and all the Products shall be shipped at the Purchaser’s risk. Seller shall not be responsible or liable for any loss of income and/or profits, or incidental, special, consequential damages resulting from Seller’s delayed performance in shipment and delivery.
5. RETURN OF DEFECTIVE PRODUCTS Defective or failed material shall be held at the Purchaser’s premises until authorization has been granted by Seller to return or dispose of Products. Products that are to be returned for final inspection must be returned Freight Prepaid in the most economical way. Credit will be issued for material found to be defective upon Seller’s inspection based on prices at time of purchase.
6. PRODUCTS ORDERED IN ERROR Products may be returned, provided that claim is made and Seller is notified within 7 days of receipt of Products, and the Products are in original buyer’s possession not more than 30 days prior to return, subject to Seller’s approval. If Products are accepted for return, they must be Freight Prepaid and buyer will be charged a minimum of 15% restocking charge, plus a charge back for outbound freight charges if the original order was shipped prepaid. Returns are not accepted for any Products that are specifically manufactured to meet the buyer’s requirement of either specifications or quantity.
AGREEMENTS These Terms and Conditions constitute the entire agreement between Seller and Purchaser as it relates to terms and conditions of sale, and supersedes any and all prior oral or written agreements, correspondence, quotations or understandings heretofore in force between the parties relating to the subject matter hereof. There are no agreements between Seller and Purchaser with respect to the Product herein except those specifically set forth in and made part of these terms and conditions. Any additional terms, conditions and/or prices are rejected by Seller.

1. PRICE All prices set forth on any purchase order or other document are F.O.B. Sellers facility or distribution point, as may be determined by Seller (F.O.B.Point). All prices are exclusive of any and all taxes, including, but not limited to, excise, sales, use, property or transportation taxes related to the sale or use of the Products, now or hereafter imposed, together with all penalties and expenses. Purchaser shall be responsible for collecting and/or paying any and all such taxes, whether or not they are stated in any invoice for the Products. Unless otherwise specified herein, all prices are exclusive of inland transportation, freight, insurance and other costs and expenses relating to the shipment of the Products from the F.O.B. point to Purchaser’s facility. Any prepayment by Seller of freight insurance and other costs shall be for the account
of Purchaser and shall be repaid to Seller.

These terms and conditions may be modified, cancelled or rescinded only by a written agreement of both parties executed by their duly authorized agents.
USE ONLY GENUINE EDCO PARTS & ACCESSORIES
For your own safety, the safety of others and the life of your machine.
SUBMIT ALL WARRANTY CLAIMS AT:
edcoinc.com/warranty-request-claim/

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 23

E-DS18-PL-0324

BEFORE USING THIS PRODUCT
Have You Used EDCO’s Online Customer Support??

Scan This QRC or Visit www.edcoinc.com/customer-support
READ: EDCO Owner’s Manuals and Parts Listings share basic information
and parts of each product. Download and print them whenever needed.

WATCH: EDCO Product Training Videos show how to use products, install
tooling, and perform basic maintenance.

Example Only

FIND: Somewhere on this product is an EDCO QRC Training Decal. Scanning
this code provides owner’s information, videos, and other training content anywhere/anytime on your mobile device.

JOIN: EDCOed.com is a free, 24-hour training space. Each certification track
focuses on a specific EDCO product group. The information in these tracks help businesses be successful with those products.

EDCO is always updating online training / information so you always have the most recent content. Also see Operator’s Safety & Limited Warranty Manual
Equipment Development Co., Inc. · 800.638.3326 · techsupport@edcoinc.com

Page 24

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>