EDCO BTSPK166 Wireless LED Speaker User Manual
- June 8, 2024
- EDCO
Table of Contents
EDCO BTSPK166 Wireless LED Speaker
Specifications
- Operation range: 10M
- Battery: built-in rechargeable 1200mAh Lithium-ion
- Output power: 5W*2
- Input voltage: DC 5V
- Frequency response: 100Hz-20KHz
- Loudspeaker: 3inch 5W
- Distortion: 10%
- S/N ratio: 80dB
- Multimedia input: Micro SD/USB
- FM frequency range: 87.5-108.0Mhz
Description of Parts
- Power ON/OFF
- Micro SD(TF) card slot
- USB slot
- Charging port
- LED button
- M button
- Previous track / Volume-
- Play/Pause
- Next track / Volume+
Wireless Mode
Turn on the speaker to enter wireless mode. Pair with a device to play
music. Press Play/Pause button to control playback. Use the Previous/Next
track buttons for track navigation. Long-press Volume buttons to adjust the
sound level.
USB/TF Card
Insert a USB flash drive or Micro-TF card into the corresponding slot. The
speaker will automatically read MP3 format music. Use the Play/Pause button to
control playback and the Previous/Next track buttons for navigation.
FM Radio
Press the play button to search for FM channels automatically. The scan
procedure may take several minutes. Once completed, use the track buttons to
move forward or backward. Long-press Volume buttons to adjust the volume.
TWS (True Wireless Stereo)
To pair two speakers, turn them on, select one unit, and long-press its M
button until you hear a confirmation sound. This indicates a successful
pairing. Ensure both units are not connected to other devices before pairing.
Charging
Connect the speaker’s charging port to a power source using the provided
USB cable. The red LED indicator will light up during charging.
FCC Warning
This device complies with FCC regulations. Avoid causing harmful
interference and accept any received interference. Consult a professional for
help if needed.
IC Warning
This equipment complies with ISED radiation exposure limits. Maintain a
minimum distance of 20cm between the device and your body during operation.
FAQ
-
Q: How do I reset the speaker?
A: To reset the speaker, press and hold the Power button for about 10 seconds until the device powers off. Then turn it back on as usual. -
Q: How do I switch between different modes?
A: Use the mode button on the speaker to cycle through different modes such as Wireless, USB/TF Card, FM Radio, and TWS. -
Q: Can I use the speaker while it is charging?
A: Yes, you can use the speaker while it is charging. However, it is recommended to avoid doing so for extended periods to maintain battery health.
MODEL NO.: BTSPK166
PMN : WIRELESS LED SPEAKER
HVIN : BTSPK166
ACCESSORIES
- Power supply cable: 1PCS
- Unser manual: 1PCS
SPECIFICATIONS
- Operation range: 10M
- Battery: built-in rechargeable 1200mAh Lithium-ion
- Output power: 5W*2
- Input voltage: DC 5V
- Frequency response: 100Hz-20KHz
- Loudspeaker: 3inch 5W
- Distortion: ≤10%
- S/N ratio: ≥80dB
- Multimedia input: Micro SD/USB
- FM frequency range: 87.5-108.0Mhz
DESCRIPTION OF PARTS
- Power ON/OFF
- Micro SD(TF) card slot
- USB slot
- Charging port
- LED button
- M button
- Previous track / Vol-
- Play/Pause
- Next track / Vol+
WIRELESS
Turn on the speaker and it will come into the wireless mode directly. After pairing the device, it can play the music. Press “ ” button to Play/Pause. Short press “ ” or “ ” button to be the previous track or the next track, long press “ ” or “ ” button to increase or decrease the Volume.
USB/TF Card
Insert the U flash memory or Micro-TF card into the USB/TF slot, and KTX-1475
will read the MP3 format music automatically. Press button to Play/Pause,
press “ ” or “ ” button to the previous track and the next track.
FM RADIO
Press to search FM channels automatically. This operation will scan all FM
stations and Pre-record them to memory. The scan procedure will take several
minutes and cannot be interrupted. Once completed, you can short press “ ” or
button to move forward or backward. Long press “ ” or button to increase or
decrease the Volume.
TWS
Two same unit speakers, turn on them first, choose one unit, and long press its “M’’ button for several seconds, when you listened the sound of “Ding- tong’’, that is to say the two units have already paired well. Please ensure before pairing the two units have not connected with other devices.
CHARGING
Plug the USB cable into the speaker’s charging port and connect to the power source. The red LED indicator on the panel will be lit when the unit is charging.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:(1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used by the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.
IC Warning
This device complies with Industry Canada license‐exempt RSSstandard(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device. The
digital apparatus complies with Canadian CAN ICES‐003 (B)/NMB‐3(B).
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.