EDCO 2D-HDP Heavy Duty Floor Grinder Polisher Instruction Manual

: July 20, 2024
: EDCO

Table of Contents

2D-HDP Heavy Duty Floor Grinder Polisher
Product Information
Specifications:
Product Usage Instructions:
FAQ

2D-HDP Heavy Duty Floor Grinder Polisher

“`html

Product Information

Specifications:

Model: E-2DHDP-PL-0124
Type: Heavy-Duty Floor Grinder/Polisher
Power Source: Propane
SKU: 58200

Product Usage Instructions:

Safety Information:

Before operating the equipment, thoroughly read and understand
the operator’s safety manual available at
edcoinc.com/customer-resources/manuals-parts-lists/.

Ensure to read and understand the engine manufacturer’s
instructions and operator’s manual before operation.

General Instructions:

Avoid placing body parts, loose clothing, and accessories near
moving parts to prevent accidents.
Maintain a safe distance from flammable materials as sparks
from the machine can ignite them.

How to Order Replacement Parts:

Always use genuine EDCO replacement parts for product safety and
reliability. When ordering parts, specify the model and serial
number found on the nameplate. Provide part number, description,
and quantity to your parts representative.

FAQ

Q: Where can I find the operator’s safety manual?

A: The operator’s safety manual can be accessed at
edcoinc.com/customer-resources/manuals-parts-lists/.

Q: How should I maintain a safe operating distance from

flammable materials?

A: Ensure to keep a safe distance from any flammable materials
to prevent sparks from igniting them.

“`

E-2DHDP-PL-0124 REVISED STARTING SERIAL # 240110445
PARTS LIST MANUAL
®
HEAVY-DUTY FLOOR GRINDER / POLISHER

PROPANE MODEL 2D-HDP SKU # 58200

READ AND UNDERSTAND THE OPERATOR’S SAFETY MANUAL THOROUGHLY
BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT.
Death or serious injury could occur if this machine is used improperly. Machine specific Operator’s Instruction Manuals are offered at edcoinc.com /customer-resources/manuals-parts-lists/
READ AND UNDERSTAND THE ENGINE MANUFACTURERS INSTRUCTIONS AND OPERATORS MANUAL BEFORE OPERATION.

EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: 800-638-3326 or 301-663-1600 · Fax: 800-447-3326 or 301-663-1607 800-63W8-e3b3s2it6e:·wewdwc.oedinccoi.ncco.cmom· t·ecEh- msuapil:pteocrht@suepdpocrot@inecd.ccooinmc.com

Printed in USA JWA ©2024
Page 1

E-2DHDP-PL-0124

SAFETY INFORMATION

SAFETY MESSAGES
· Safety Instructions are proceeded by a graphic alert symbol of DANGER, WARNING, or CAUTION.
Indicates an imminent hazard which, if not avoided, will result in death or serious injury.
Indicates an imminent hazard which, if not avoided, can result in death or serious injury.
Indicates hazards which, if not avoided, could result in serious injury and or damage to the equipment.

ELECTRICAL POWERED EQUIPMENT CONTINUED
· Do not disconnect power by pulling cord. To disconnect, grasp the plug, not the cord.
· Unplug power cord at the machine when not in use and before servicing.
· Switch motor OFF before disconnecting power. · Never use frayed, damaged, taped or under rated extension cords.
Electrical shock could result in death or serious injury to the operator and damage to the equipment. · Assure you are using the proper extension cord length.

GASOLINE / PROPANE POWERED EQUIPMENT
· Engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. · Tilting a gasoline powered machine fitted with an EPA approved vented charcoal filter gas cap, beyond 20° can cause fuel leakage. If a leak occurs, do not start or run the engine until the leak is fixed. Eliminate all other ignition sources in the immediate area (no smoking, flares, sparks or flames). Use approved gasoline absorbing material to contain the fuel leakage. Then use clean, non-sparking tools to collect absorbed materials then dispose of these contaminants properly. · Gasoline is extremely flammable and poisonous. It should only be dispensed in well ventilated areas, and with a cool engine. · Small gasoline engines produce high concentrations of carbon monoxide (CO) example: a 5 HP 4 cycle engine operation in an enclosed 100,000 cu. ft. area with only one change of air per hour is capable of providing deadly concentrations of CO in less than fifteen minutes. Five changes of air in the same area will produce noxious fumes in less than 30 minutes. Gasoline powered equipment should not be used in enclosed or partially enclosed areas. Symptoms of CO poisoning include, head-ache, nausea, weakness, dizziness, visual problems and loss of consciousness. If symptoms occur – get into fresh air and seek medical attention immediately. · Never refuel a hot engine or an engine while it is running. · Engines are shipped from factory without fuel/oil. · Propane is extremely flammable and is heavier than air and tends to settle in low areas where a spark or flame could ignite gas. DO NOT start or operate this propane engine in a poorly ventilated area where leaking propane gas could accumulate and endanger safety of persons in area. If headache develops, shut off machine. Have it checked for carbon monoxide emissions by a qualified technician before using it again. To ensure personal safety, installation and repair of propane fuel supply systems must be performed only by qualified technicians. Carbon monoxide emissions from this machine are greatly increased due to a dirty combustion air cleaner.
ELECTRICAL POWERED EQUIPMENT
Extreme care must be taken when operating electric models with water present: Ensure power cord is properly grounded, is attached to a Ground-Fault- Interrupter (GFI) outlet, and is undamaged. · Check all electrical cables – be sure connections are tight and cable is continuous and in good condition. Be sure cable is correctly rated for both the operating current and voltage of this equipment. · Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with qualified electrician or service person if there is any doubt as to whether the outlet is properly grounded. Adhere to all local codes and ordinances. · NOTE: In the event of a malfunction or breakdown, grounding provides a path of least resistance for the electric current to dissipate. The motor is equipped with a grounded plug and must be connected to an outlet that is properly installed and properly grounded. DO NOT modify the plug provided on the motor. If the plug does not fit the outlet have a qualified electrician install the proper receptacle.

GENERAL INSTRUCTIONS
· Equipment should only be operated by trained personnel in good physical condition and mental health (not fatigued). The operator and maintenance personnel must be physically able to handle the bulk weight and power of this equipment.
· This is a one person tool. Maintain a safe operating distance to other personnel. It is the operators’ responsibility to keep other people (workers, pedestrians, bystanders, etc.) away during operation. Block off the work area in all directions with roping, safety netting, etc. Failure to do so may result in others being injured by flying debris or exposing them to harmful dust and noise.
· This equipment is intended for commercial use only. · For the operator’s safety and the safety of others, always keep all
guards in place during operation. · Never let equipment run unattended.
· Personal Protection Equipment and proper safety attire must be worn when operating this machinery. The operator must wear approved safety equipment appropriate for the job such as hard hat and safety shoes when conditions require. Hearing protection MUST be used when operational noise levels of this equipment may exceed 85db. Eye protection MUST be worn at all times.
Keep body parts, loose clothing and accessories away from moving parts. Failure to do so could result in dismemberment or death.
· Do not modify the machine. · Stop motor/engine when adjusting or servicing this equipment. Maintain
a safe operating distance from flammable materials. Sparks from the cutting- action of this machine can ignite flammable materials or vapors.
DUST WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects, or other reproductive harm. Materials being removed can be toxic or hazardous. A breathing respirator is required to help protect the operator. Some examples of these chemicals are: · Lead from lead-based paints. · Crystalline silica from bricks, concrete and other masonry products.Your risk of exposure to these chemi cals varies depending on how often you do this type of work. To reduce your risk: work in a well ventilated area, use a dust control system, such as an industrialstyle vacuum, and wear approved personal safety equipment, such as a dust/particle respirator designed to filter out microscopic particles. · See more on the importance of dust prevention and silica warnings at: osha.gov/silica · More concrete and silica dust supression training and educational materials available at edcoinc.com/silica-standards or scan the QR code on page 5. · Written exposure plans are provided at http://www.edcoinc.com/writtenexposure-control-plans/

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 2

PARTS LIST MANUAL
®

E-2DHDP-PL-0124

HEAVY-DUTY FLOOR GRINDER/POLISHER
PROPANE MODEL

TABLE OF CONTENTS

Section

Page Number

Safety Messages and General Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 How To Order Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Illustration 1: Main Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 5 Illustration 2: Handle & Wheel Carriage Grouping . . . . . . . . . . . . . . . . . . . . . . . . 6, 7 Illustration 3: Skirt, Vacuum Port & Water Hook-Up Grouping . . . . . . . . . . . . . . . 8, 9 Illustration 4: Standard Grinding Disc Assemby . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Illustration 5: Optional Polishing Disc Assemby . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Illustration 6: Propane Engine & Belt Drive Grouping . . . . . . . . . . . . . . . . . . . . . . 12, 13 Illustration 7: Propane Tank Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 15 Illustration 8: Electrical Component Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 17 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Key Switch Wire Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Other Wire Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Decal Sheet 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Decal Sheet 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Limited Equipment Warranty of Sale – Terms & Conditions . . . . . . . . . . . . . . . . . . 23 STOP: Before Using this Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

HOW TO ORDER REPLACEMENT PARTS
To insure product safety and reliability, always use genuine EDCO replacement parts when making repairs to the equipment.
When calling for parts, specify the MODEL and SERIAL number of the machine, which can be found on the NAME PLATE. Keep that information in the space provided. In addition to this information, give part number, description, and quantity as listed on the parts list to your parts representative.
Please note: Due to improvements and changes in the equipment, the illustrations shown may be different than the actual machine.

FILL IN INFORMATION BELOW Date of Purchase __ Model # _____ Serial # __ SKU #

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 3

E-2DHDP-PL-0124
ILLUSTRATION 1: MAIN GROUPING

Page 4

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

E-2DHDP-PL-0124

ITEM #
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
28 29 30 31 32 33 34 35 36 37 38 39 40

PARTS LISTING – ILLUSTRATION 1 : MAIN GROUPING

PART #

DESCRIPTION

77501 77502 10005

MAIN FRAME COVER, GEAR CASE PLUG, HOLE 7/8″ BRIGHT ZINC

11697 10018 10038 10602 77008

SCREW, FLANGE HEX 1/4-20 X 3 SCREW, CAP 1/4-20 X 3/4 WASHER, LOCK 1/4 ZINC WASHER, FLAT 1/4 SAE ZINC BEARING, BALL 1″ 4-HOLE FLANGE, ND

10450 10481 77009 50541 10699

WASHER, LOCK 7/16 ZINC NUT, HEX 7/16-20 ZINC BEARING, BALL 3/4″ 4-HOLE FLANGE ADAPTER, GREASE FIT. 1/8PT X 1/4-28 PIPE NIPPLE 1/8NPT X 2″ (BLACK)

10585 10953 10960 10309 10811

PIPE COUPLING 1/8 NPT (BLACK STEEL) FITTING, GREASE 1/8 NPT STRAIGHT FITTING, GREASE 1/4-28 X 45° SCREW, CAP 3/8-24 X 1-1/4 ZINC WASHER, LOCK 3/8 ZINC

10014 77346 77012 63056 77011

NUT, HEX 3/8-24 ZINC SHAFT, LARGE GEAR 1″DIA X 7″L GEAR, SPUR 112 TOOTH (DRIVEN) PIN, H.D.COILED SPRING 3/8 X 2-1/2 SHAFT, PINION GEAR 3/4DIA X 7-3/8″L

10037 77053 10009 101201
10007

PIN, ROLL 1/4 X 1-1/2 GEAR, SPUR 25 TOOTH (PINION) WASHER, FLAT 3/4 SAE ZINC MT GRINDING DISC ASSEMBLY (REFER TO ILLUSTRATION 4 FOR BREAKDOWN) PIN, ROLL 3/8 X 2-1/2

100961 10025 10811 10907 77506

HOOD, PROPANE MODEL WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK 3/8 ZINC SCREW, CAP 3/8-16 X 3/4 WEIGHT BLOCK, 40 LB.

59117 11871 10462 77532 10025

LEVEL, SCREW ON SCREW, MACHINE FHP 8-32 X 1-1/4 NUT, KEPS LOCK 8-32 ZINC (NOT SHOWN) LIFTING BAIL WASHER, FLAT 3/8 SAE ZINC

10811 10309

WASHER, LOCK 3/8 ZINC SCREW, CAP 3/8-24 X 1-1/4 ZINC

QTY.
1 1 1 2 6 8 6 4 16 16 2 1 1 1 1 3 4 4 4 2 2 2 1 1 1 1 2
2 1 2 2 2 2 1 2 2 1 4 4 4

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 5

E-2DHDP-PL-0124

ILLUSTRATION 2: HANDLE & WHEEL CARRIAGE GROUPING

Page 6

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

E-2DHDP-PL-0124

PARTS LISTING – ILLUSTRATION 2 : HANDLE & WHEEL CARRIAGE GROUPING

ITEM # PART #

DESCRIPTION

QTY.

1

77533

HANDLE BAR, PROPANE MODEL

1

2

10608

GRIP, HAND 1″ MODEL AT

2

3

10029

SCREW, CAP 3/8-24 X 1-3/4

4

10025

WASHER, FLAT 3/8 SAE ZINC

8

5

10004

NUT, HEX LOCK 3/8-24 ZINC

4

6

77508

HANDLE EXTENSION

1

7

77528

PLUG, BLACK 1″RD. TUBING 10-14 GA.

2

8

10030

SCREW, CAP 3/8-24 X 2

2

9

10025

WASHER, FLAT 3/8 SAE ZINC

4

10

10004

NUT, HEX LOCK 3/8-24 ZINC

2

11

65019

HANDWHEEL, SMALL W/ 5/8-8 X 13″ROD

1

12

14023

KNOB, BALL 1-3/8 W/ 1/2-13THD, BLK.

1

13

50550

SLEEVE, BRASS 1/2″ TAPERED

1

14

10346

SCREW, SKT. HD. CAP 1/2-13 X 4-1/2

1

15

80009

BEARING, BALL 5/8″ 2-HOLE (NO G.F.)

1

16

55010

SPACER, HANDWHEEL 5/8″ID X 3/4″L

1

17

10096

COLLAR, LOCKING 5/8″ID

2

18

10412

BOLT, CARRIAGE 1/4-20 X 1

2

19

10602

WASHER, FLAT 1/4 SAE ZINC

2

20

10861

NUT, KEPS LOCK 1/4-20 ZINC

2

21

10808

FITTING, GREASE 1/4-28 STRAIGHT

1

22

77534

LINKAGE, LOWER

1

23

10343

SCREW, CAP 1/2-20 X 2-1/2

1

24

10154

NUT, HEX NYLON LOCK 1/2-20 ZINC

1

25

77510

CARRIAGE, WHEEL

1

26

77537

FORK SHAFT 3/4″DIA. X 13-3/4″L

1

27

68008

WHEEL 8 X 1-5/8 X 3/4″BRG., POLY

2

28

77520

WHEEL 4 X 1-1/2 X 3/4″BRG., POLY

2

29

10009

WASHER, FLAT 3/4 SAE ZINC

14

30

10428

COLLAR, LOCKING 3/4″ID

6

31

77501

MAIN FRAME (REFER TO ILLUS. 1)

1

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 7

E-2DHDP-PL-0124
ILLUSTRATION 3: SKIRT, VACUUM PORT & WATER HOOK-UP GROUPING

Page 8

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

E-2DHDP-PL-0124

ITEM # 1 2 3 4 5 6
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

PARTS LISTING – ILLUSTRATION 3 : SKIRT, VACUUM PORT & WATER HOOK-UP GROUPING

PART #

DESCRIPTION

77529

RUBBER SKIRT 1/8 X 8 X 58 W/VELCRO

77504

RUBBER SKIRT, REAR 1/8 X 4 X 11

10018

SCREW, CAP 1/4-20 X 3/4

10038

WASHER, LOCK 1/4 ZINC

10602

WASHER, FLAT 1/4 SAE ZINC

77556

VELCRO-HOOK ONLY 2″ X 72″ 1 PIECE CUT 57-1/4″L & 2 PIECES CUT 4-1/2″L

77551

HOSE, FLEX 2″ID X 36″L

10766

CLAMP, HOSE, SAE #32, ADJ. TO 2-1/2

77538

VACUUM PORT

65021

CAP/PLUG 2″ RED PLASTIC, FLANGED

10846

SCREW, CAP STSHW 1/4-20 X 1/2

10038

WASHER, LOCK 1/4 ZINC

—–

SIDE PANELS, HANDLE (REFER TO ILLUS. 7)

77533

HANDLE BAR, PROP. MODEL (REFER TO ILLUS. 2)

10711A

VALVE & HOSE CONNECTOR ASSY.

50075

BARB, 3/8 HOSE X 1/4MPT (BRASS)

77521

HOSE 3/8″ID X 18″L

10714

CLAMP, HOSE, SAE #4, ADJ. TO 5/8″

10694

BARB, 3/8HOSE X 1/8MPT

10772

ELBOW, STREET 1/8NPT X 45 (BRASS)

77501

MAIN FRAME (REFER TO ILLUS. 1)

QTY. 1 1 2 2 2 1
1 2 1 1 2 2 2 1 1 1 1 2 1 1 1

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 9

E-2DHDP-PL-0124

ILLUSTRATION 4: STANDARD GRINDING DISC ASSEMBLY
®
DISC ARRANGEMENT
INSTALL DISC IN OPPOSITE DIRECTIONS SO THEY PASS EACH OTHER AT THE CENTER IN ALTERNATING SEQUENCE.

BOTTOM VIEW

ITEM # 1-13 1
2
3 4 5 6 7 8 9 10 11 12 13
Page 10

PART # 101201

PART #

DESCRIPTION

101201

MT GRINDING DISC ASSEMBLY

100054

10″ UNIVERSAL MAGNA-TRAP DISC (INCLUDES MAGNETS)

36064

MAGNET, NEODYMIUM RING 7/8 X 1/8 (BOLT ON REPLACEMENT)

10647

SCREW, FLAT HD PHILLIPS 8-32 X 1/2

10462

NUT, KEPS LOCK 8-32 ZINC

100055

RING, RUBBER, 4-1/2″OD X 1/2″THK

100985

HUB SPACER, MAGNA-TRAP DISC, 2DHD

100057

HUB, GRINDER DISC

11855

SCREW, SKT. HD. CAP 3/8-24 X 3-1/4

11856

SCREW, SKT. HD. CAP 3/8-24 X 3-1/2

10113

SPACER, STEEL 9/16OD X 3/8ID X 7/32

10011

SPACER, STEEL 5/8OD X 3/8ID X 3/8T

10004

NUT, HEX LOCK 3/8-24 LOCK (USE RED LOCTITE)

11725

NUT, HEX JAM 3/8-24 ZINC (USE RED LOCTITE)

*NOTE: QUANTITIES ARE BASED ON 1 DISC. 2 DISC ARE REQUIRED.

QTY.* 1 1
3
3 3 2 1 1 3 3 3 6 3 3

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

ILLUSTRATION 5: OPTIONAL POLISHING DISC ASSEMBLY
®

E-2DHDP-PL-0124

DISC ARRANGEMENT

BOTTOM VIEW

PART # 77535

ITEM # 1-13 1 2 3 4 5 6 7 8 9 10 11 12 13

PART #

DESCRIPTION

77535

MT POLISHING DISC ASSEMBLY

75175

DISC ONLY, POLISHING, 2DHD

QC-HOLDER-EDCO

HOLDER, MAGNETIC QUICK CHANGE

10147

SCREW, FLAT HD SKT 1/4-20 X 3/4

L18567

DISC TOP PLATE, POLISHING

11614

SCREW, CAP 1/2-20 X 3/4

10045

WASHER, LOCK 1/2 ZINC

86017

COUPLING, MORFLEX 402 CENTER

77518

FLANGE, MORFLEX COUPLING

10114

SCREW, SKT. HD. CAP 3/8-24 X 2-1/4

11695

WASHER, 1.1210 X .3750 X .1280

10811

WASHER, LOCK 3/8 ZINC

86343

BUSHING, RUBBER 1-1/4 X 3/4 X 3/8

10004

NUT, HEX LOCK 3/8-24 ZINC

*NOTE: QUANTITIES ARE BASED ON 1 DISC. 2 DISC ARE REQUIRED.

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

QTY.* 1 1 3 6 1 3 3 1 1 4 2 2 4 4

Page 11

E-2DHDP-PL-0124
ILLUSTRATION 6: PROPANE ENGINE & BELT DRIVE GROUPING

Page 12

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

E-2DHDP-PL-0124

PARTS LISTING – ILLUSTRATION 6 : PROPANE ENGINE & BELT DRIVE GROUPING

ITEM # PART #

DESCRIPTION

QTY.

1

15081

ENGINE, KAWASAKI LX600 PROP. READY

1

INCLUDES:

12V STARTER, OIL PRESSURE SWITCH, OIL DRAIIN,

CATALYTIC MUFFLER.

LP FUEL SYSTEM: REGULATOR, INLINE SHUT-OFF VALVE,

HIGH & LOW PRESSURE HOSES, & REGO TANK CONNECTOR.

2

15295

SWITCH, OIL PRESSURE, 3 POLE

1

3

15296

ADAPTER 1/8-27 FNPT TO 1/8-28 BSP

1

4

77539

MOUNT, ENGINE, PROPANE

1

5

10055

SCREW, CAP 3/8-16 X 1

8

6

10811

WASHER, LOCK 3/8 ZINC

8

7

10025

WASHER, FLAT 3/8 SAE ZINC

8

75195

SPACER, CLUTCH, 2DHDP

1

9

10139

SCREW, SET 1/4-20 X 5/16

1

10

75194

SLEEVE ADAPTER, 1″ TO 1-1/8″ W/ KEY

1

11

77541

BRACKET, CLUTCH RETAINER

1

12

10004

NUT, HEX LOCK 3/8-24 ZINC

2

13

75193

CLUTCH & BRAKE, MAGNETIC GT3.5-MC07

1

14

77542

WASHER, CLUTCH RETAINING

1

15

10450

WASHER, LOCK 7/16 ZINC

1

16

11699

SCREW, CAP 7/16-20 X 1-3/4

1

17

10277

BELT B-38

1

18

10549

SHEAVE 7″OD X 1GR.B X 3/4″BORE

1

19

10016

KEY 3/16SQ X 1-1/2

1

20

3611

CABLE, THROTTLE, LEVER-TYPE 54″ (TRIMMED TO 44″LOA)

1

21

10877

SCREW, CAP STSHW 10-24 X 1/2

3

22

10831

WASHER, LOCK, INT. TOOTH #10

3

23

10941

CLIP, CONDUIT, THROTTLE CABLE

1

24

75173

BATTERY 12V, INTERSTATE FAYTX20HL

1

25

77543

RUBBER PAD, BATTERY 3/16 X 3-3/8 X 7

1

26

77555

CLAMP, BATTERY HOLD-DOWN

1

27

10055

SCREW, CAP 3/8-16 X 1

1

28

10811

WASHER, LOCK 3/8 ZINC

1

29

10025

WASHER, FLAT 3/8 SAE ZINC

1

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 13

E-2DHDP-PL-0124

ILLUSTRATION 7: PROPANE TANK GROUPING

Page 14

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

E-2DHDP-PL-0124

ITEM # 1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20 21 22

PARTS LISTING ILLUSTRATION 7: PROPANE TANK GROUPING

PART # 15099 100399 101126 77061-2 77061-3 77061-4 11661 10602 10861 10320 10802 10025 10811 10404 77547 100965 77549 10021 10025 10004 10029 10025 10004

DESCRIPTION PROPANE TANK 20LB. VAPOR PROPANE TANK CRADLE BRACKET PROPANE TANK LOCATOR BRACKET PROPANE TANK STRAP W/ HINGE PROPANE TANK CLAW BRACKET PROPANE TANK TOGGLE CLAMP SCREW, FLAT HD SLT 1/4-20 X 1 WASHER, FLAT 1/4 SAE ZINC NUT, KEPS LOCK 1/4-20 ZINC BOLT, CARRIAGE 3/8-16 X 1-1/4 ZINC BOLT, CARRIAGE 3/8-16 X 1 ZINC WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-16 ZINC DECK, PROPANE TANK SIDE PANEL, HANDLE RIGHT SIDE PANEL, HANDLE LEFT SCREW, CAP 3/8-24 X 1 WASHER, FLAT 3/8 SAE ZINC NUT, HEX LOCK 3/8-24 ZINC SCREW, CAP 3/8-24 X 1-3/4 WASHER, FLAT 3/8 SAE ZINC NUT, HEX LOCK 3/8-24 ZINC

QTY. 1 1 1 1 1 1 4 4 4 2 2 4 4 4 1 1 1 4 8 4 4 8 4

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 15

E-2DHDP-PL-0124

ILLUSTRATION 8: ELECTRICAL COMPONENT GROUPING

Page 16

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

E-2DHDP-PL-0124

PARTS LISTING ILLUSTRATION 8: ELECTRICAL COMPONENT GROUPING

ITEM # PART #

1

15201A

2 3 4 5 6 7 8 9 10
11
12 13
NOT SHOWN

50084 10831 10877 11567 75184 15264 75183 75171 10018 10602 10861 57148 75182
75173
15296 15295 75180 75181

DESCRIPTION SWITCH W/ WIRES, ROCKER RED ON-OFF (EMERGNCY STOP) ADDITIONAL PARTS REQ’D. (NOT SHOWN):
TERM., RING #10 16-14GA. INSULATED WASHER, LOCK, INT. TOOTH #10 SCREW, CAP STSHW 10-24 X 1/2 CONNECTOR, BULLET STD. 16-14GA.BLUE SWITCH, ROCKER ON-OFF, RED, CLUTCH LAMP, OIL PRESSURE, RED SWITCH, KEY STARTER SOLENOID SWITCH, STARTER SCREW, CAP 1/4-20 X 3/4 WASHER, FLAT 1/4 SAE ZINC NUT, KEPS LOCK 1/4-20 ZINC GROMMET 3/8ID X 1/8GRV. X 5/8GD CLUTCH, ELECTRIC, 1 GR00VE (REFER TO ILLUS. 6) BATTERY 12V, INTERSTATE FAYTX20HL (REFER TO ILLUS. 6) ADAPTER 1/8-27 FNPT TO 1/8-28 BSP SWITCH, OIL PRESSURE, 3 POLE FUSEHOLDER, 1-30A, ATC BLADE FUSE, 20A, ATC BLADE

QTY. 1
1 1 1 1 1 1 1 1 2 2 2 1 1
1
1 1 1 1

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 17

E-2DHDP-PL-0124

WIRING DIAGRAM

Page 18

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

KEY SWITCH WIRE HARNESS
PART # 300104

E-2DHDP-PL-0124

PART # 10675 10968 10977 11567 11582 11867 51049

DESCRIPTION TERMINAL, FEM., KOHLER 25-452-01-S TERM., RING 5/16 16-14GA. INSULATED TERM., RING #10 12-10GA. INSULATED CONNECTOR, BULLET STD. 16-14GA.BLUE CONNECTOR, BULLET 3-WAY FEMALE CONNECTOR, LINE STD. 22-18GA.(RED) CONNECTOR, WIRE HARNESS, FEMALE

QTY. 5 1 1 3 2 1 1

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 19

E-2DHDP-PL-0124

OTHER WIRES ASSEMBLIES

Page 20

PART # 10938 10955 10968 10977 50084 75180 75181

DESCRIPTION CONNECTOR, BUTT 16-14GA. INSULATED TERM., FEM. PUSH-ON 1/4″ 16-14GA. TERM., RING 5/16 16-14GA. INSULATED TERM., RING #10 12-10GA. INSULATED TERM., RING #10 16-14GA. INSULATED FUSEHOLDER, 1-30A, ATC BLADE FUSE, 20A, ATC BLADE

QTY. 1 1 1 11 1 1 1

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

DECAL SHEET 1

E-2DHDP-PL-0124

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 21

E-2DHDP-PL-0124

DECAL SHEET 2

Page 22

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

LIMITED EQUIPMENT WARRANTY OF SALE

E-2DHDP-PL-0124

Equipment Development Company, Inc. herein referred to as EDCO (Seller) warrants that each new unit manufactured by EDCO to be free from defects in material and workmanship in normal use and service for a period of (1) one year (except for the cutter drum assembly on all model concrete/asphalt planers AND the chisel head assembly on all model ALR’s & ALR-BS in which case the warranty period shall be 90 days) from date of shipment to the original retail or equipment rental center owner.
Accessories or equipment furnished and installed on the product by EDCO but manufactured by others, including, but not limited to engines, motors,electrical components, transmissions etc., shall carry the accessory manufacturers own warranty.
EDCO will, at its option, repair or replace, at the EDCO factory or at a point designated by EDCO, any part which shall appear to the satisfaction of EDCO inspection to have been defective in material or workmanship.
EDCO reserves the right to modify, alter and improve any part or parts without incurring any obligation to replace any part or parts previously sold without such modified, altered or improved part or parts.
This warranty is in lieu of and excludes all other warranties, expressed, implied, statutory, or otherwise created under applicable law including, but not limited to the warranty of merchantability and the warranty of fitness for a particular purpose in no event shall seller or the manufacturer of the product be liable for special, incidental, or consequential damages, including loss of profits, whether or not caused by or resulting from the negligence of seller and/or the manufacturer of the product unless specifically provided herein. In addition, this warranty shall not apply to any products or portions there of which have been subjected to abuse, misuse, improper installation, maintenance, or operation, electrical failure or abnormal conditions and to products which have been tampered with, altered, modified, repaired, reworked by anyone not approved by seller or used in any manner inconsistent with the provisions of the above or any instructions or specifications provided with or for the product.
TERMS AND CONDITIONS
(NOT APPLICABLE TO SALES THROUGH AUTHORIZED DISTRIBUTION)
FORCE MAJEURE Seller’s obligation hereunder are subject to, and Seller shall not be held responsible for, any delay or failure to make delivery of all or any part of the Product due to labor difficulties, fires, casualties, accidents, acts of the elements, acts of God, transportation difficulties, delays by a common carrier, inability to obtain Product, materials or components or qualified labor sufficient to timely perform part of or all of the obligations contained in these terms and conditions, governmental regulations or actions, strikes, damage to or destruction in whole or part of manufacturing plant, riots, terrorist attacks or incidents, civil commotions, warlike conditions, flood , tidal waves, typhoon, hurricane, earthquake, lightning, explosion or any other causes, contingencies or circumstances within or without the United States not subject to the Seller’s control which prevent or hinder the manufacture or delivery of the Products or make the fulfillment of these terms and conditions impracticable. In the event of the occurrence of any of the foregoing, at the option of Seller, Seller shall be excused from the performance under these Terms and Conditions, or the performance of the Seller shall be correspondingly extended.
This document sets forth the terms and conditions pursuant to which the purchaser (“Purchaser”) will purchase and Equipment Development Co.Inc. (“Seller”)will sell the products, accessories, attachments (collectively the Products “) ordered by the Purchaser. These terms and conditions shall govern and apply to the sale of Seller’s Products to Purchaser, regardless of any terms and conditions appearing on any purchase order or other forms submitted by Purchaser to Seller, or the inconsistency of any terms therein and herein.

2. PAYMENT TERMS Payment terms are as follows. 2% 10 days (to approved and qualified accounts). Net 30 days. This is a cash discount for invoices paid within 10 days after the invoice date, regardless of date of receipt of shipment. This is not a trade discount and will not be granted to accounts that do not adhere to stated terms. All past due accounts are subject to a late payment fee of 1.5% per month or a maximum allowed by law if different, along with the expenses incidental to collection including reasonable attorney’s fees and costs. Seller reserves the right to hold shipments against past due accounts. *Seller reserves the right to alter payment terms.
3. FREIGHT TERMS All shipments will be made F.O.B. shipping point as designated in these Terms and Conditions, and title shall pass at the F.O.B. point. Delivery to the initial common carrier shall constitute delivery to the Purchaser. Any claims for loss or damage during shipment are to be filed with carrier by the Purchaser. Seller will not assume responsibility for the performance of the carrier.
Back orders will be shipped in the most practical fashion with charges consistent with our freight policy established with the original order. UPS, FED EX, MAIL or shipments by other couriers are subject to the same terms and conditions as outlined in paragraph #3″Freight Terms”.
4. DELIVERY, DAMAGES, SHORTAGES Seller shall use reasonable efforts to attempt to cause the Products to be delivered as provided for in these Terms & Conditions. Delivery to the initial common carrier shall constitute the delivery to the Purchaser. Sellers responsibility, in so far as transportation risks are concerned ceases upon the delivery of the Products in good condition to such carrier at the F.O.B. point and all the Products shall be shipped at the Purchaser’s risk. Seller shall not be responsible or liable for any loss of income and/or profits, or incidental, special, consequential damages resulting from Seller’s delayed performance in shipment and delivery.
5. RETURN OF DEFECTIVE PRODUCTS Defective or failed material shall be held at the Purchaser’s premises until authorization has been granted by Seller to return or dispose of Products. Products that are to be returned for final inspection must be returned Freight Prepaid in the most economical way. Credit will be issued for material found to be defective upon Seller’s inspection based on prices at time of purchase.
6. PRODUCTS ORDERED IN ERROR Products may be returned, provided that claim is made and Seller is notified within 7 days of receipt of Products, and the Products are in original buyer’s possession not more than 30 days prior to return, subject to Seller’s approval. If Products are accepted for return, they must be Freight Prepaid and buyer will be charged a minimum of 15% restocking charge, plus a charge back for outbound freight charges if the original order was shipped prepaid. Returns are not accepted for any Products that are specifically manufactured to meet the buyer’s requirement of either specifications or quantity.
AGREEMENTS These Terms and Conditions constitute the entire agreement between Seller and Purchaser as it relates to terms and conditions of sale, and supersedes any and all prior oral or written agreements, correspondence, quotations or understandings heretofore in force between the parties relating to the subject matter hereof. There are no agreements between Seller and Purchaser with respect to the Product herein except those specifically set forth in and made part of these terms and conditions. Any additional terms, conditions and/or prices are rejected by Seller.

1. PRICE All prices set forth on any purchase order or other document are F.O.B. Sellers facility or distribution point, as may be determined by Seller (F.O.B.Point). All prices are exclusive of any and all taxes, including, but not limited to, excise, sales, use, property or transportation taxes related to the sale or use of the Products, now or hereafter imposed, together with all penalties and expenses. Purchaser shall be responsible for collecting and/or paying any and all such taxes, whether or not they are stated in any invoice for the Products. Unless otherwise specified herein, all prices are exclusive of inland transportation, freight, insurance and other costs and expenses relating to the shipment of the Products from the F.O.B. point to Purchaser’s facility. Any prepayment by Seller of freight insurance and other costs shall be for the account
of Purchaser and shall be repaid to Seller.

These terms and conditions may be modified, cancelled or rescinded only by a written agreement of both parties executed by their duly authorized agents.
USE ONLY GENUINE EDCO PARTS & ACCESSORIES
For your own safety, the safety of others and the life of your machine.
SUBMIT ALL WARRANTY CLAIMS AT:
edcoinc.com/customer-support/warranty-claim-form/

800-638-3326 · edcoinc.com · techsupport@edcoinc.com

Page 23

E-2DHDP-PL-0124

BEFORE USING THIS PRODUCT
Have You Used EDCO’s Online Customer Support??

Scan This QRC or Visit www.edcoinc.com/customer-support
READ: EDCO Owner’s Manuals and Parts Listings share basic information
and parts of each product. Download and print them whenever needed.

WATCH: EDCO Product Training Videos show how to use products, install
tooling, and perform basic maintenance.

Example Only

FIND: Somewhere on this product is an EDCO QRC Training Decal. Scanning
this code provides owner’s information, videos, and other training content anywhere/anytime on your mobile device.

JOIN: EDCOed.com is a free, 24-hour training space. Each certification track
focuses on a specific EDCO product group. The information in these tracks help businesses be successful with those products.

EDCO is always updating online training / information so you always have the most recent content. Also see Operator’s Safety & Limited Warranty Manual
Equipment Development Co., Inc. · 800.638.3326 · techsupport@edcoinc.com

Page 24

800-638-3326 · edcoinc.com · techsupport@edcoinc.com