EDCO BTWS300 Bluetooth Earbuds User Manual
- June 12, 2024
- EDCO
Table of Contents
EDCO BTWS300 Bluetooth Earbuds
Product Information
- Product Name: BTWS300
- Pairing Bluetooth Name: BTWS300
- Bluetooth Version: 5.1
- Wireless Support Protocol: A2DP, AVRCP, HSP, HFP
- Earbud Battery Capacity: 50mAh*2
- Charging Case Battery Capacity: 2000mAh
- Charging Time: 1-2 hours
- Charging Port: Micro USB
- Frequency: 2.402-2.480GHz
- Play Time: 3-4 hours
- Speaker: 16
- Standby Time: 150 hours
Product Usage Instructions
Attention
- Do not crash, scratch, or warp the earbuds. Avoid throwing them into water.
- Keep the earbuds away from magnets and speakers while using them.
- Avoid extreme temperatures. The working condition should be between -10°C to 50°C (14°F to 122°F).
- Avoid moist environments.
Warning
- Do not use the product while charging. Use the original charger provided.
- The Li-polymer battery should not be opened, thrown into fire, connected with metal, or short-circuited.
- Avoid crashing the product and keep it away from moist corrosion environments.
- Avoid using the product under heating conditions exceeding 60°C (140°F).
Package List
- Bluetooth earbuds: 1 pair
- Charging case: 1
- Instruction book: 1
FCC Warning
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment. This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver .
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected .
- Consult the dealer or an experienced radio / TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
ISEDC Radiation Exposure Statement
This equipment complies with ISEDC RF radiation exposure limits set forth
for an uncontrolled environment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Power on/off
- Power On: take out the earbuds from charging case, auto power on or long touching the multi-function until the led in red and blue.
- Power off: Put the earbuds back to charging case, auto power off and charging, long touching the multi-function until the led flashing in Red and lighting off
Pairing
- Take out from charging case, earbuds auto paring, then search bluetooth match name” BTWS300” on your Cell phone, and pair to the Cell phone.
- LED light flash red and blue while pairing
- LED light off when pair to cell phone successfully.
Answer/refuse call
- Answer call: short touch either earbud, touch again hang up call
- Refuse call: long touch 2 seconds either earbuds.
**Play music
**
- Short touch either earbud to pause
- Double short touch “L” earbud to play next song, Double short touch “R” earbud to play Previous song. Triple short touch “L” earbud to volume +, Triple short touch “R” earbud to volume – .
- Long touch 2 seconds on either earbud to wake voice assistant.
Charging
- Put the earbuds to the charging case, auto charging.
- Inset the cable to Charge for the charging case, LED Red light on while charging, and light off , charging complete.
Earbuds and Charging Case Technical details
- Pairing Bluetooth name : BTWS300
- Bluetooth Version: 5.1
- Wireless Support Protocol: A2DP,AVRCP,HSP,HFP Earbud Battery capacity: 50mAh*2
- Battery capacity: 2000mAh
- Charging time: 1-2 Hour
- Charging Port: Micro USB
IC Warning
This device complies with Innovation, Science and Economic Development Canada
licence-exempt RSS standard (s). Operation is subject to the following two
conditions
- This device may not cause interference
- This device must accept any interference, including interference that may cause undesired operation of the device.
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.