V I V O STAND-TV13E Large Mobile TV Cart Instruction Manual

: August 9, 2024
: V I V O

Table of Contents

V I V O STAND-TV13E Large Mobile TV Cart
Product Specifications
Product Usage Instructions
FAQ
Package Contents
Included Hardware & Tools
ASSEMBLY STEPS
Cable Management Options
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

V I V O STAND-TV13E Large Mobile TV Cart

Product Specifications

Brand: Vivo
Model: STAND-TV13E
Weight Capacity:
- TV: 110 lbs (50 kg)
- Shelf: 10 lbs (4.5 kg)

Product Usage Instructions

The package includes various components needed for assembly:
- The package also includes hardware and tools required for assembly:
Thread the Casters (I) into Long and Short Feet (A, B) using the provided Wrench (T-D).
Carefully thread Pole Connectors (G) into the top of Lower Poles (E) and secure using the provided tools.
WARNING: Pole Connector threads may be sharp. Use a cloth or towel for a better grip.
Insert the opposite ends of the Lower Poles (E) into Base (C1) and secure using the provided screws and Allen Wrench.

FAQ

Q: What is the weight capacity of the TV cart?
A: The weight capacity for the TV is 110 lbs (50 kg) and for the shelf is 10 lbs (4.5 kg).
Q: What should I do if I receive damaged parts?
A: If any parts are received damaged or defective, please contact our support team at 309-278-5303 for assistance in replacing the parts.

CAUTION!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo- us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

WARNING: CHOKING HAZARD

SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

DO NOT EXCEED WEIGHT CAPACITY

FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.

TIP OVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER.
TO HELP PREVENT TIPOVER:

NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV CART
USE TIP-OVER RESTRAINT OR ANCHOR STAND TO WALL

THE USE OF TIP-OVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

We’re Here for You
Open Monday – Friday 7:00 am – 7:00 pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

Give us a Call: 309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
Chat Us: www.vivo-us.com AVG. RESOLUTION TIME (within office hrs): < 15 M
Email Us: help@vivo-us.com AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr

Package Contents

Included Hardware & Tools

Tools Needed

Weight Capacity

ASSEMBLY STEPS

STEP 1

Thread Casters (I) into Long and Short Feet (A,B) using Wrench (T-D).

STEP 2

Separate Base (C) into Base (C1) and Cover (C2).

STEP 3

Secure Long & Short Feet (A,B) to the underside of the Base (C1) using M6x60mm Screws (S-B), M6 Large Washers (S-A), Foot Brackets (L), and 5mm Allen Wrench (T-C).

Assembly Note
Short Feet (B) should be installed on the back of Base (C1), which is labeled to indicate the back side.

Leveling Casters
If the caster can’t touch the ground, loosen the lower nut as shown to adjust the caster to proper position, then tighten the upper nut.

STEP 4

Carefully thread Pole Connectors (G) into the top of Lower Poles (E), ensuring they thread in straight. Tighten to fully secure.

WARNING: Pole Connector threads may be sharp. When connecting, grip the Pole Connector with a cloth or towel to achieve sufficient force when threading into the poles.

Insert the opposite ends of the Lower Poles (E) into Base (C1) and secure using M6x10mm Screws (S-C) and 4mm Allen Wrench (T-B).
Slide Cover (C2) down Lower Poles (E) and onto Base (C1).
Gently push Rubber Rings (D) into the Cable Slots on Lower Poles (E).

STEP 5

Carefully thread Center Poles (Q) onto Lower Poles (E), then thread Upper Poles (F) onto Center Poles. Only tighten poles when you are certain they are threading in straight.
Connect Pole Caps (H) to create two caps, and insert into the tops of the Upper Poles.

STEP 6

Hold Pole Bracket Pads (J) onto Pole Brackets (K), and slide them together onto Upper Poles (F) at the desired height of your TV. Secure in place using 4mm Allen Wrench (T-B).
Ensure Pole Bracket Set Screws are facing the back of the assembled stand.

STEP 7

Attach TV Plate (O) to Pole Brackets (K) using M6x10 Screws (S-C), M6 Small Washers (M-I) and 4mm Allen Wrench (T-B).

STEP 8

Secure VESA Bracket Set (P) to the back of your TV using appropriate Screws (M-A through M-G) with Washers (M-H through M-J), and Spacers (M-K through M-M) and Phillips end of 5mm Allen Wrench (T-C).

STEP 9

Adjusting TV Plate Positioning

Before mounting your TV, ensure the TV Plate (O) is level using Level (T-E). If the Plate needs to be adjusted for levelness or height, loosen Set Screws on Pole Brackets (K) using 4mm Allen Wrench (T-B) and adjust as needed. Tighten again to secure.

Mounting Your TV

Hang TV onto TV Plate (O) and secure by tightening Locking Screws using the Phillips end on 5mm Allen Wrench (T-C)

Adjusting TV HeightHeight

Loosen Set Screws on Pole Brackets (K) using 4mm Allen Wrench (T-B) and adjust as needed. Tighten again to secure.

STEP 10

Attach Shelf Supports (N) to Lower Poles (E) using M6x10mm Screws (S-C) and 4mm Allen Wrench (T-B). Do not fully tighten screws yet.

Attach Shelf (M) to Shelf Supports (N) using M4x6mm Screws (S-E) and the Phillips end on 5mm Allen Wrench (T-C).
Fully tighten previously installed M6x10mm Screws (S-C) with 4mm Allen Wrench (T-B).

STEP 11