V I V O STAND-V202Q Pneumatic Arm Dual Ultrawide Monitor Desk Mount Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
SKU: STAND-V202Q
Pneumatic Arm Dual Ultrawide Monitor Desk Mount
Instruction Manual
STAND-V202Q Pneumatic Arm Dual Ultrawide Monitor Desk Mount
https://vivo-us.com/products/stand-v202q
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
| |
---|---|---
help@vivo-us.com| www.vivo-us.com
Chat live with an agent!| 309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity.
We cannot be liable for damage or injury caused by improper mounting,
incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1 (Option A)
Clamp Installation
Secure Upper Clamp (E) to the underside of Base (D) using M6x10mm Flathead
Screws (S-B) and 4mm Allen Wrench (T-B). Remove adhesive backing and apply
Pads (K) to the underside of Base (D). Connect Lower Clamp (F) to the front of
Upper Clamp (E) using M6x10mm Screws (S-B) and 4mm Allen Wrench (T-B). For
desktops 10-55mm (3/8” to 2 1/4”) thick, use top holes on Upper Clamp. For
desktops 50-85mm (2” to 3 3/8”) thick, use the bottom two holes. Secure clamp
assembly to desktop by tightening the hand bolt. Affix Cable Clamp Clip (G) to
the back of clamp assembly. STEP 1 (Option B)
Grommet Installation
Insert Carriage Bolt (S-A) into Grommet Plate (H) and secure to underside of
Base (D) using M6x10mm Flathead Screws (S-B) and 4mm Allen Wrench (T-B). Peel
back adhesive backing and apply Pads (K) to underside of Base (D). Place base
assembly over grommet hole in desktop and place Support Plate (I) and Knob (J)
on the end of Carriage Bolt (S-A). Tighten Knob (J) to secure. STEP 2
Place Lower Arms (B) onto Base (D) and secure by tightening set screws with
3mm Allen Wrench (T-A). Install Upper Arms (A) on Lower Arms (B) and tighten
set screws with 3mm Allen Wrench (T-A) to secure. STEP 3
Secure VESA Plates (C) to back of monitors using appropriate Screws (M-A thru
M-D), M6 Washers (M-E), and 6mm Allen Wrench (T-C). Use Spacers (M-F) for
curved monitor. STEP 4
Place monitors with VESA Plates (C) onto Upper Arms (A) and secure with
M6x12mm Thumbscrews (S-C). STEP 5
While holding Upper Arm (A) in the horizontal position, adjust the gas spring
tension using 6mm Allen Wrench (T-C). Adjusting Tension
Decrease Strength – If the arm raises up, turn the adjustment screws
clockwise until it holds the monitor in a horizontal position. Increase
Strength – If the arm does not have enough movement, turn the adjustment
screws counterclockwise. CAUTION
To avoid damage to the monitor and mount, always keep the arm in a horizontal
position while making adjustments.
Cable Management Covers
Lower Arm (B):
1. Slide covers forward to remove.
2. Place cables in covers.
3. Connect inner tabs to clips on arm to secure in place.| Upper Arm
(A):
1. Pull tabs outward on lower portion of covers.
2. Pull upper tabs outward to fully remove covers.
3. Place cables in covers.
4. Re-install by snapping upper tabs in place, then snap lower tabs on to
fully secure.
---|---
Adjustments
Adjust monitor placement as desired. Allen Wrenches (T-B, T-C) can be stored
in Cable Clamp Clip (G) for future adjustments. Love your new VIVO setup and
want to share?
Tag us in your photo! @vivo_us
LAST UPDATED: 11/29/2022
REV1
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
| 309-278-5303| AVG. RESOLUTION TIME (within office hrs): 5M 4S
---|---|---
| www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15 M
| help@vivo-us.com| AVG. RESPONSE TIME (within
office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT:
www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Pneumatic Arm Dual Ultrawide Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>