V I V O STAND-V100D Pneumatic Arm Single Ultrawide Monitor Desk Mount Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
Pneumatic Arm Single Ultrawide
Monitor
Desk Mount
Instruction Manual
SKU: STAND-V100Dhttps://vivo-us.com/products/stand-v100d
STAND-V100D Pneumatic Arm Single Ultrawide Monitor Desk Mount
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-us.com/products/stand-v100d
WARNING!
If you do not understand these directions, or if you have any doubts about
the safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Cut the shipping tie from Arm (A) while firmly holding the two halves close
together. Slowly release the pressure and allow it to gradually open up to
reach full extension.
STEP 2: Option A – Desk Clamp
Assemble Upper Clamp (B) to the underside of Arm (A) using M6x12mm Screws
(S-C) and 4mm Allen Wrench (T-A). Place Pad (F) to bottom of Upper Clamp (B).
Loosen bolts on Lower Clamp (C) using 6mm Allen Wrench (T-B). Turn Clamp over
and place Support Plate (H) over bolt ends. 
Slightly loosen back side screws on Lower Clamp (C), allowing 6mm to be exposed. Slide Lower Clamp (C) into the appropriate keyholes of Upper Clamp (B) based on desktop thickness. Use lower holes for desktops 50-85mm (2” to 3 3/8”) thick, and upper holes for desktops 10-58mm (3/8” to 2 1/4”).
Secure screws on Lower Clamp (C) using 4mm Allen Wrench (T-A). Tighten lower
bolts on Lower Clamp (C) to secure to desktop using 6 mm Allen Wrench (T-B).
Proceed to Step 3 at the bottom of Page 5
Option B – Grommet
Assemble Grommet Plate (G) to under side of Arm (A) using M6x12mm Screws (S-C) and 4mm Allen Wrench (T-A). Apply Pad (F) to Grommet Plate (G).
Remove Bolts (C1) from Lower Clamp (C) using 6mm Allen Wrench (T-B). Insert one Bolt (C1) into middle hole of Support Plate (H).
If you are using an existing grommet hole, ensure that it is at least 10mm (3/8”) in diameter and no more than 60mm (2 3/8”). Desktop should be between 10mm-48mm (3/8” to 1 7/8”) . For desktops without an existing grommet hole, use a 3/8” (10mm) drill bit to drill through desktop.
Place mount asembly over grommet hole and secure to desktop using Support Plate (H), Bolt (C1), and 6mm Allen Wrench (T-B).
Connect VESA Plate (D) to Arm (A) using Spacer (S-A), M8x25mm Screw (S-B), and 6mm Allen Wrench (T-B). Ensure that hexagon side of space is facing upward towards VESA Plate (D). Remove Thumbscrew (D1) from back of VESA Plate (D). Separate Front VESA Plate (D2) from Back VESA Plate (D3). Set aside.
Connect Front VESA Plate (D2) to back of Monitor using appropriate Screws (M-A, M-B), M5 Washers (M-C), and a Phillips Screwdriver.
To mount the monitor, begin by lining up the tabs on Front VESA Plate (D2) with the slots on Back VESA Plate (D3). Insert tabs into slots and re-install Thumbscrew (D1) into Back VESA Plate (D3) to secure.
While holding the arm in the horizontal position, adjust the gas spring tension using 6mm Allen Wrench (T-B).
CAUTION – To avoid damage to the monitor and mount, always keep the arm in a horizontal position while making adjustments.
How to adjust if…
ARM DROPS – If the arm drops, turn the adjustment screw counter clockwise until it holds the monitor in a horizontal position.
ARM RISES – If the arm raises up, turn the adjustment screw clockwise until it
holds the monitor in a horizontal position.
Remove Cable Cover (A1) from Arm (A) by sliding it forward. Route cables and
replace Cover (A1).
Place Clamp Cable Clip (E) onto backside of assembly for additional cable
management. 4mm and 6mm Allen Wrenches (T-A, T-B) can be stored in slots for
future adjustments.
To keep mount stable, do not extend arm fully behind desktop edge.
Adjust the tilt using the 6mm Allen Wrench (T-B).
Adjust the monitor position as desired.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
AVG. RESOLUTION TIME (within office hrs): 5M 4S
AVG. RESOLUTION TIME (within office hrs): < 15 M
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
309-278-5303
www.vivo-us.com
Chat live with an agent!
**help@vivo-us.com
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT:**
www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Pneumatic Arm Single Ultrawide Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>