V I V O MOUNT-VWKB2 Dual Monitor Wall Mounts Plus Keyboard Tray Wall Mount Instruction Manual

: August 14, 2024
: V I V O

Table of Contents

MOUNT-VWKB2 Dual Monitor Wall Mounts Plus Keyboard Tray Wall Mount
We’re Here for You
Package Contents
Keyboard Tray
Tools Needed
ASSEMBLY STEPS
Keyboard Tray
Height Adjustment
Adjust Tilt Angle
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Dual Monitor Wall Mounts
+ Keyboard Tray Wall Mount

Instruction Manual
SKU: MOUNT-VWKB2

MOUNT-VWKB2 Dual Monitor Wall Mounts Plus Keyboard Tray Wall Mount

Assembly Video & Product Info
www.vivo-us.com/products/mount-vwkb2

CAUTION!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo- us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.
WARNING: PINCH POINT
DO NOT PLACE HANDS ON OR NEAR SUPPORT BARS. MOVING PARTS CAN CRUSH AND CUT.
PINCH POINTS ARE CREATED DURING LIFTING AND LOWERING THE WORK SURFACE. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS PERSONAL INJURY.

We’re Here for You

Open Monday – Friday 7:00am – 7:00pm CS T, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

Give us a Call:
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
Chat Us: www.vivo-us.com
AVG. RESOLUTION TIME (within office hrs): < 15 M

Email Us: help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr

Monitor Mount

Package Contents

Included Hardware & Tools

Keyboard Tray

Included Hardware & Tools

Tools Needed

Weight Capacity

ASSEMBLY STEPS

STEP 1
Loosen the screw on the side of both Wall Mounts (A) and slide off VESA Plates (A1).

STEP 2

Place Wall Mounts (A) in the desired location against the wall and mark drilling locations with a pencil. Use of a level is recommended.
Wood Wall: Drill 1.75” (45mm) deep holes using a 3/32” (2.5mm) drill bit.
Drywall: Drill holes using a 5/16” – 25/64” (8 – 10mm) drill bit.

STEP 3
Assemble VESA Plate (A1) to the back of monitors using Screws (M-A or M-B) and M6 Washers (M-C).

STEP 4
Slide VESA Plate (A1) back into Wall Mount (A) and secure by retightening the screw.

STEP 5
Raise monitors by lifting up. To lower, raise it up to the highest setting, then slowly lower it.

Keyboard Tray

ASSEMBLY STEPS
STEP 1
Wood Stud Installation

Wood Wall – Cont’D
Secure Arm (B) to the wall using ST6.3x55mm Screws (W-A) and M6 Washers (W-C).

Brick/Concrete

Brick/Concrete – Cont’D
Insert Concrete Anchors (W-B) into holes. Secure Arm (B) to the wall using ST6.3x55mm Screws (W-A) and M6 Washers (W-C).

STEP 2
ALL installation Types
Insert Covers (J) into the mounting holes in Arm.

STEP 3
Assemble Left & Right Keyboard Tray Pieces (C,D) using Keyboard Tray Bracket (E) with M4x8mm Screws (S-A) and a Phillips screwdriver.

Mount the keyboard tray assembly to Arm (B) using M4x12mm Flat Head Screws (S-B) and M4 Nuts (S-C). Tighten using Wrench (T-A) and a Phillips screwdriver.

STEP 4
Remove the adhesive backing from Wrist Pad (G) and place it assembed keyboard tray along with Mouse Pad (F). STEP 5
Route cables through the Cable Management Channels in Arm (B).

Height Adjustment

Position Arm
Position the arm at desired height and firmly hold in place.
Insert the 6mm Allen Wrench (T-B) Into Adjustment Screw
Insert 6mm Allen Wrench (T-B) in to the adjustment screw on the back of the monitor arm.
Turn 10-20x to Set Monitor Height
Turn 6mm Allen Wrench (T-B) 10-20 times to obtain proper support for your monitor.
Use the guide below to adjust the tension according to the amount of counterbalance needed to support the monitor.

Clockwise:
Decrease Support
[if arm will not lower]

Turn the adjustment screw
clockwise to decrease the support for your monitor, allowing it to be lowered.

Counter-Clockwise Increase Support
[if arm will not raise]

Turn the adjustment screw counter-clockwise to increase the support for your monitor, allowing it to be raised up.

Note: Requires 10-20 Turns