artika CLGL-HD1 Ceiling LED Light Fixture Instruction Manual
- June 5, 2024
- artika
Table of Contents
artika CLGL-HD1 Ceiling LED Light Fixture Instruction
Item | Description | Quantity |
---|
| Junction box screw| ****
× 2
| Wire connector|
× 3
| Canopy screw|
× 2 + 1 extra
| Mounting Bracket Support|
× 1
|
Ceiling LED Light Fixture
| ****
× 1
| ****
Wall anchor
| ****
× 2
| Retaining screw|
×
WHAT YOU WILL NEED…
-
Pencil
-
Screwdriver
-
Drill
-
¼ in drill bit (6.5 mm)
IMPORTANT
The installer and/or user must read, understand and follow these instructions before installing the product. This product must be properly installed before it is used. If instructions are not followed, the manufacturer will not be held responsible for any problems or product malfunction. Failure to follow installation and/or operating instructions voids the warranty. We recommend that this product be installed by a certified electrician. In some states or provinces, it is a legal requirement for this type of product to be installed by a certified electrician, according to the electrical and building codes effective in the region where the unit is used. This product is compatible with most LED dimmers
WARNING: Risk of electrical shock. Turn off breaker at the panel.
Switch off the main electrical supply from the fuse box/circuit breaker before
installing the unit or doing any maintenance.
Do not use outdoor.
STEP-BY-STEP INSTALLATION
-
Turn off power at the circuit breaker and the light switch. Ensure the power is off before continuing.
-
Install the mounting bracket to the junction box. Place marks on the ceiling where the retaining screw holes will be located.
Remove the mounting bracket. -
Drill pilot holes in the ceiling with a ¼ in. (6.5 mm) drill bit Push wall anchors into the holes.
-
Attach the mounting bracket to the junction box with the two junction box screws (fi g. 1).
WARRANTY
Artika For Living Inc. is proud to offer you a three (3) year limited warranty
on manufacturing defects from the date of purchase for residential use only.
The warranty is extended to the original owner in USA and Canada and is non-
transferable. It does not apply to retailers, commercial applications or
establishments. The original sales receipt is required for all warranty
claims. The remedy under this limited warranty shall be product or part
replacement at Artika’s discretion as provided herein and cannot exceed the
original purchase price. This warranty is valid only on products installed in
accordance with the building code and laws effective in the region where the
unit is used as well as in accordance with the provided instruction manual. It
does not cover products installed incorrectly or subjected to abnormal use.
Product(s) or component part(s) may be required to be returned for inspection
and verification. Normal wear and tear, misuse, negligence, vandalism,
improper maintenance (surface damage due to chemical interaction or cleaning
agents including, but not limited to, scouring pads, use of cleaners
containing abrasives, alcohol or other organic solvents) improper handling,
accident, abuse, fi re, flood, theft, acts of God, neglect, or alteration of
the product will not be covered under this limited warranty. It excludes any
accessories that accompany the product including but not limited to bulbs or
batteries. The warranty does not cover handling, labor, transportation, or any
other cost associated with the installation or replacement of the product.
This limited warranty is valid in the country of purchase and by Artika
authorized retailers only. Artika for Living Inc. will not be held responsible
for any direct or consequential damages or injuries related to the use of this
product arising from improper use or installation of this product.
Please visit www.artika.com to discover more about
Artika for Living Inc
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception.
However, there
is no guarantee that interference will not occur in a particular installation.
If this equipment causes harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of
thefollowing measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Attach the hook to the mounting bracket.
- Connect the white wire (N) from the light fixture to the white supply wire (N) from the junction box using a wire connector. Connect the black wire (L) from the light fixture to the black supply wire (L) from the junction box using a wire connector. Connect the ground wire (G) from the light fixture to the ground supply wire (G) from the junction box using a wire connector (fi g. 2).
- Put the wires into the canopy.
- Mount the canopy onto the mounting bracket and secure it with the canopy screws (fi g. 3).
- Restore electrical power.