ROUGH COUNTRY 921931770 Polaris Xpedition Bed Window Molle Panel Installation Guide
- July 21, 2024
- Rough Country
Table of Contents
ROUGH COUNTRY 921931770 Polaris Xpedition Bed Window Molle Panel
Installation Guide
Thank you for choosing Rough Country for all your vehicle needs.
Please read instructions before beginning installation. Check the kit hardware
against the kit contents shown below. Be sure you have all needed parts and
know where they go.
If question exist, please call us
@1-800-222-7023. We will be happy to
answer any questions concerning this product.
Check all fasteners for proper torque. Check to ensure for adequate clearance
between all components. Periodically check all hardware for tightness.
Torque Specs:
| Size | Grade 5 | Grade 8 | Size | Class 8.8 | Class 10.9 |
|---|---|---|---|---|---|
| 5/16” | 15 ft/lbs | 20ft/lbs | 6MM | 5ft/lbs | 9ft/lbs |
| 3/8” | 30 ft/lbs | 35ft/lbs | 8MM | 18ft/lbs | 23ft/lbs |
| 7/16” | 45 ft/lbs | 60ft/lbs | 10MM | 32ft/lbs | 45ft/lbs |
| 1/2” | 65 ft/lbs | 90ft/lbs | 12MM | 55ft/lbs | 75ft/lbs |
| 9/16” | 95 ft/lbs | 130ft/lbs | 14MM | 85ft/lbs | 120ft/lbs |
| 5/8” | 135ft/lbs | 175ft/lbs | 16MM | 130ft/lbs | 165ft/lbs |
| 3/4” | 185ft/lbs | 280ft/lbs | 18MM | 170ft/lbs | 240ft/lbs |
| Part | QTY | Description | |||
| --- | --- | --- | |||
| A | 1 | Dr. Side MOLLE Panel | |||
| B | 1 | Pass. Side MOLLE Panel | |||
| C | 8 | 6mm x 30mm Button Head Bolt | |||
| D | 8 | 6mm Body Clip | |||
| E | 6 | Spacer | |||
| F | 8 | 6mm Flat Washer |
**A.
**
B.
**C.
**
**D.
**
**E.
**
F.
INSTALLATION INSTRUCTIONS
- Install the supplied clip nuts into the two upper mounting holes of the panel. See Photo 1.
- Install the panel to the vehicle using the upper mounting holes with the supplied spacer, flat washers, and button head bolts. Tighten with a 4mm Allen wrench. NOTE: The top inner mounting hole does not need a spacer. See Photo 2.
- Use a paint pen to mark the two lower mounting holes. See Photo 3.
- Remove the panel using a 4mm Allen wrench and set aside the hardware.
- Make a hole in the previously marked locations with a 1/4” drill. See Photo 4.
- Use the supplied spacers, flat washers, and button head bolts to mount the panels to the vehicle. Tighten with a 4mm Allen wrench. NOTE: The top inner mounting hole does not need a spacer. See Photo 5.
- Repeat for other side.
POST INSTALLATION INSTRUCTIONS
- Check all fasteners for proper torque. Check to ensure for adequate clearance between all rotating, mobile, fixed, and heated members. Verify clearance between exhaust and brake lines, fuel lines, fuel tank, floorboards, and wiring harness.
- Perform head light check and adjustment to proper settings.
- All kit components must be retightened at 500 miles and then every 300 miles after installation. Periodically check all hardware for tightness.
- Install “Warning to Driver” decal on sun visor.
By purchasing any item sold by Rough Country, LLC, the buyer expressly warrants that he/she is in compliance with all applicable, State, and Local laws and regulations regarding the purchase, ownership, and use of the item. It shall be the buyers responsibility to comply with all Federal, State and Local laws governing the sales of any items listed, illustrated or sold. The buyer expressly agrees to indemnify and hold harmless Rough Country, LLC for all claims resulting directly or indirectly from the purchase, ownership, or use of the items.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>