TELTONIKA FMC125 Tracking Device For Fleet Telematics

Specifications:

• Product Name: FMC CAN Adapters FMC125
• Compatible CAN Adapters: LV-CAN200, ALL-CAN300, CAN-CONTROL, SIMPLE-CAN, MINI-CAN
• Power Supply Voltage: Up to 30V
• Connection Interface: CAN L, CAN H

Product Usage Instructions

Installing CAN Adapter with FMC125 Device
Installing LV-CAN200/ALL-CAN300/CAN-CONTROL

Tools Needed for Installation:

• LV-CAN200/ALL-CAN300/CAN-CONTROL Connection scheme
• FMC125 device
• Pliers
• Quick splice connectors
• Plastic pry tool
• Zip ties

Installation Steps:

1. Prepare the vehicle connection scheme received from Teltonika Sales Representative.
2. Check the scheme for current vehicle connection and match PIN numbers and colors.
3. Connect CAN adapter with FMC125:
   • Connect CAN adapter PIN 6 (Rx) to INPUT 6 of FMC125.
   • Connect CAN adapter PIN 5 (Tx) to INPUT 5 of FMC125.
4. Connect CAN adapter CAN wires (CAN L, CAN H) as per scheme.
5. Connect CAN adapter positive and ground wires to the vehicle power supply lines or near FMC125 power wires.
6. Switch vehicle ignition to ACC position to activate the CAN adapter.
7. Configure CAN adapter to read CAN bus data or control vehicle by setting its program number – CAN Adapter configuration.

Installing LV-CAN200/ALL-CAN300 + SIMPLE-CAN

Tools Needed for Installation:

• LV-CAN200/ALL-CAN300 Connection scheme
• SIMPLE-CAN
• FMC125 device
• Pliers
• Quick splice connectors
• Plastic pry tool
• Zip ties

https://wiki.teltonika-gps.com/view/

Template: FMC_CAN_adapters_FMC125
Easy steps to install and configure following CAN adapters on FMC125 device:

• LV-CAN200
• ALL-CAN300
• CAN-CONTROL
• SIMPLE-CAN
• MINI-CAN

Installing CAN adapter with FMC125 device

Installing LV-CAN200/ALL-CAN300/CAN-CONTROL
You can watch the LV-CAN200/ALL-CAN300 installation video in our YouTube channel here or follow the connection instructions below.

Tools needed for installation

• LV-CAN200/ALL-CAN300/CAN-CONTROL
• Connection scheme (Please contact Teltonika Sales Representative and provide information about vehicle manufacturer, model and year.
• FMC125 device
• Pliers
• Quick splice connectors (If vehicle CAN bus wires are very thin CAN adapter wires should be connected directly)
• Plastic pry tool
• Zip ties

Installation steps

1. Be ready with a vehicle connection scheme that you have received from a Teltonika Sales Representative.
2. Check the scheme for the current vehicle connection. Look for connectors matching PINs numbers and colors (may be different) according to connection scheme.
3. Connect CAN adapter with FMC125:
4. Connect CAN adapter PIN 6 (Rx) to INPUT 6 of FMC125.
5. Connect CAN adapter PIN 5 (Tx) to INPUT 5 of FMC125.
6. Connect CAN adapter CAN wires (CAN L, CAN H) as specified in connection scheme. Do not swap CAN L and CAN H lines. Not all CAN adapter wires may be used in vehicle.
7. Connect CAN adapter positive and ground wires to the vehicle power supply lines or near FMC125 power wires. Do not swap power supply lines. Make sure that voltage does not exceed 30V.
8. Switch vehicle ignition to ACC position. CAN adapter LED diode on the back should start blinking.
9. Configure CAN adapter to read CAN bus data or control vehicle by setting its program number – CAN Adapter configuration

• LV-CAN200/ALL-CAN300 connection example. This is not a connection diagram for your vehicle. Every vehicle has a specific scheme.
• CAN-CONTROL connection example. This is not a connection diagram for your vehicle. Every vehicle has a specific scheme.

Installing LV-CAN200/ALL-CAN300 + SIMPLE-CAN

You can watch LV-CAN200/ALL-CAN300 + SIMPLE-CAN installation video in our YouTube channel here or follow connection instructions below.

Tools needed for installation

• LV-CAN200/ALL-CAN300
• Connection scheme (Please contact Teltonika Sales Representative and provide information about vehicle manufacturer, model and year.
• SIMPLE-CAN (Used for contactless connection. If two CAN lines need to be connected, two
• SIMPLE-CAN’s must be used.)
• FMC125 device
• Pliers
• Quick splice connectors (If vehicle CAN bus wires are very thin CAN adapter wires should be connected directly)
• Plastic pry tool
• Zip ties

Installation steps

1. Follow the same 1, 2, 3 installation steps as with LV-CAN200/ALL-CAN300/CAN-CONTROL installation.

2. Connect the appropiate CAN bus pair of wires between CAN adapter and SIMPLE-CAN:
   If CAN1 line need to be connected as specified in connection scheme:

3. Connect CAN adapter CAN1 L to CAN L of SIMPLE-CAN.

4. Connect CAN adapter CAN1 H to CAN H of SIMPLE-CAN.
   If CAN2 line need to be connected as specified in connection scheme:

5. Connect CAN adapter CAN2 L to CAN L of SIMPLE-CAN.

6. Connect CAN adapter CAN2 H to CAN H of SIMPLE-CAN.
   Do not swap CAN L and CAN H lines. Not all CAN adapter wires may be used in vehicle.

7. Fasten SIMPLE-CAN between vehicle CAN bus wires according to the connection scheme. It doeasn’t matter which wire is on which side.

8. Connect CAN adapter positive and ground wires to the vehicle power supply lines or near FMC125 power wires. Do not swap power supply lines. Make sure that voltage does not exceed 30V.

9. Switch vehicle ignition to ACC position.

10. SIMPLE-CAN LED will shine continously so device awaits for calibration.

    • Press the switch shortly and wait for the LED to start blinking every one second.
    • Automatic calibration process takes up to 10 seconds depending on the vehicle model. Device is calibrated properly then the LED is blinking every 2 seconds.
    • If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.

11. Configure CAN adapter to read CAN bus data by setting its program number – CAN Adapter configuration

LV-CAN200/ALL-CAN300 + SIMPLE-CAN connection example. This is not a connection diagram for your vehicle. Follow LV-CAN200/ALL-CAN300 connection scheme suitable for your vehicle.

CAN Adapter Configuration

CAN Adapter program number selection
CAN Adapter must be set to program number which depends on the vehicle model. Needed program number is always written on CAN Adapter mounting scheme. In order to be able to enter program number in adapter Software date of CAN adapter must be newer than connection scheme date.

CAN adapter Software date can be checked:

• Via Teltonika Configurator→Status→CAN Adapter
• Via SMS command – lvcangetinfo

The number of digits required to enter correct Program No. may vary depending on the Software and manufacture date of your CAN Adapter:

• LV-CAN200 adapter changes
• ALL-CAN300 adapter changes

Entering via SMS command

Required conditions:
CAN adapter properly connected to FMC125 device

CAN adapter program number can be set remotely, using SMS command. Send following SMS command to FMC125 device:

• If you have set SMS login and password: login pass lvcansetprog X
• If SMS login and password are not set leave two spaces before command: lvcansetprog X
• Command example : lvcansetprog 11434
• SMS response: LVCAN ProgNum: 11434

If during SMS command FMC125 was in following Sleep mode:

• GPS Sleep – Program No. will be set immediately.
• Deep Sleep – Program No. will be set after device wake up.
• Online Deep Sleep – Program No. will be set immediately.
• Ultra Deep Sleep – Program No. will be set after device wake up.

Required conditions:
CAN adapter properly connected to FMC125 device

CAN adapter program number can be set via Teltonika Configurator → (1) CAN Adapter → (2)
Program Number. When program number is entered press × (3) Save to device button that saves the entered program number into FMC125.

Entering manually

• Required conditions:
  • CAN adapter properly connected to FMC125 device
  • Vehicle ignition must be ON

Depending on used CAN Adapter, length of setup sequence will vary.

Steps to set program number:

• LV-CAN200, ALL-CAN300 back
• CAN-CONTROL back

FMC125 CAN Adapter parameters configuration

Teltonika Configurator
CAN Adapter configuration can be performed using Teltonika Configurator via Micro-USB cable or Bluetooth connection when CAN Adapter is connected to the vehicle. When FMC125 is connected to the CAN Adapter, user can see all information that is received from the vehicle in Teltonika Configurator → Status → CAN Adapter tab or Teltonika Configurator → CAN Adapter section. In Status → CAN Adapter tab you can see information about CAN adapter and its readable parameters. In CAN Adapter section you can configure CAN Adapter and see incoming CAN bus data highlighted by green background color. Incoming data in both sections is automatically refreshed every 5 seconds. CAN bus data which should be readable from your vehicle is provided in “CAN Adapter supported vehicles list”, which you can get from Teltonika Sales Representative. The CAN Adapter I/O element can be configured like any other I/O element in Teltonika Configurator. All information about I/O element parameters description is in section I/O settings.

When using offline configuration method user can select which CAN data (according to vehicle) will be sent directly to the server without connection to adapter.

Send data with 0, if ignition is off
Depending on CAN Adapter I/O parameters and ignition status, FMC125 can send locked (last known) CAN Adapter I/O and active (real time) parameters values or reset values to 0. When ignition is off, CAN Adapter I/O parameters values sent to server are:

SMS Configuration
All CAN Adapter IO elements can be configured remotely via SMS commands.

SMS/GPRS Commands

• CAN Adapters have several dedicated SMS/GPRS commands.
• SMS command structure:

SMS command lvcangetinfo example:

• If you have set SMS login and password: login pass lvcangetinfo
• If SMS login and password are not set leave two spaces before command: aalvcangetinfo

GPRS commands require Codec 12 protocol.

For more SMS commands please see SMS/GPRS command list

– three digit number that identity vehicle.

| Yes
lvcansimpletacho #| Add or remove simpletacho start byte.

– 0 or 1 (0 – don’t add start byte, 1 – add start byte).

| No
lvcangetprog| Get program number from CAN Adapter that is connected to FMC125.| Yes
lvcangetinfo| Get information about connected CAN Adapter| Yes
lvcanclear #| Clear Total Mileage (counted), Engine Work Time (counted), Fuel Consumed (counted) parameters values.

– parameter (0 – Engine work time (counted), 1 – Fuel Consumed (counted), 2

– Vehicle Mileage (counted)).

| Yes
allcanmode| Turn on ALL-CAN300 mode.| Yes
lvcanmode| Turn on LV-CAN200 mode.| Yes
lvcanfaultcodes| Read DTC fault codes| Yes
CAN-CONTROL specific commands
lvcanopenalldoors| Open [unlock] all doors| Yes
lvcanclosealldoors| Close [lock] all doors| Yes
lvcanopentrunk| Open [unlock] trunk| Yes
lvcanturninglights| One flash of all turn lights ordered trough accidental / blinking turn light switch| Yes

CAN Adapter State Flags

CAN Adapters receive data about the states of various systems within the vehicle, and send them as flags to FMC125. FMC125 device stores these flags in hexadecimal format, as one variable. Bellow is a list of kept flags and how to retrieve them.

The full list of state flags is stored only by:
ALL-CAN300

Only security state flags are stored by:
CAN-CONTROL

LV-CAN200/ALL-CAN300 Important Information

Program Number logic change
Due to the growing number of supported cars, program numbers have exceeded “999”. In order to maintain one number format, we are moving from 3-digit to 4-digit program numbers.  In new LV-CAN200/ALL-CAN300 firmware (from 2017-09-01) all program numbers that were up to 999 are changed to start from 1000. So that further program numbers would continue the counting with 4-digit numbers. However, all existing program numbers stay the same, but “1” is added to the front. Device still understands the entered 3-digit program number (via SMS/GPRS), it will automatically add “1” before it. If you enter “247” – device number will turn into “1247”. In Bootloader only 4-digit format is available, just add “1” to the front of the needed program number.

Example

• When using older connection schemes where program number displayed as 3-digit program number:
• Using LV-CAN200/ALL-CAN300 Bootloader from soft version 2017-09-27 it is necessary to add “1” to the front of program number:×

FAQ

Q: What should I do if the CAN adapter LED diode does not start blinking after switching the vehicle ignition to ACC position?
A: If the LED diode does not start blinking, double-check the connections and ensure that the power supply lines are correctly connected without exceeding 30V.

Q: Can I use the same installation steps for MINI-CAN adapter?
A: The installation steps may vary for the MINI-CAN adapter. Refer to the specific user manual or contact Teltonika support for detailed instructions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>