TAKSTAR TKX-800 Digital Matrix Processor User Manual

: July 22, 2024
: TAKSTAR

Table of Contents

TAKSTAR TKX-800 Digital Matrix Processor
Functions
PC Software
PC Software Specifications
Specifications
Rear panel control port connection
232 communication protocol control code
Safety Instruction
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TAKSTAR TKX-800 Digital Matrix Processor

Specifications

24-bit sigma-delta A/D/D/A
32-bit DSP, 96kHz
AC: 95-264V, 50/60Hz
Dimensions: 482 x 254 x 44mm
Weight: 2.7kg
Frequency Response: 20Hz-20kHz, -0.3dB
Dynamic Range: 115dBu
THD: 78dBu, 1kHz Balance
+48V DC: 50dBu, 2k ohm Balance
Input Impedance: 35dBu, +18dBu >10k ohm Balance

Product Usage Instructions
Power Connection
Connect the product to an AC power source within the specified voltage range (95-264V, 50-60Hz).

Signal Input and Output
Connect your audio sources to the specified input ports with appropriate cables. Ensure proper impedance matching for optimal performance.

DSP Settings
Access the digital signal processing settings to adjust parameters such as equalization (PEQ), delay, noise reduction (NR), and volume control (VCS).

USB Connectivity
Utilize the USB ports for firmware updates or connecting the product to a computer for configuration purposes.

Frequently Asked Questions (FAQ):
Q: What is the power requirement for the TKX-800?
A: The TKX-800 operates on AC power within the range of 95-264V and at a frequency of 50-60Hz.

Functions

32 bit DSP, 96kHz sampling rate, 24bit AD/DA.
Input including, high-cut, low-cut, AGC, PEQ, independent feedback inhibition, noise gate, gain, mute, phase, delay, link.
All PEQ Gain, bandwidth, frequency continues adjustment. type can be select by PEAK, H-SHELF, L- SHELF, LOW CUT, HIGH CUT, ALLPASS1, ALLPASS2.
All inputs/outputs can do Matrix, and all the input and output channel name can be changed.
All the input and output with independent phase curve adjust function, PEQ style choose ALLPASS1 is 180° curve adjust, ALLPASS2 is 360° curve adjust.
Maximal delay time 680mS for all output channels.
Pre settings can copy for every single channel, every channel can do link adjust.
Every input and output channel PEQ curve adjusting picture can be found when you are in any input and output.
Unique design for AUX channels, mixing all microphone inputs, and professional ECHO & REVERB effects inside. easy adjustment the sound and full support karaoke function. wide-applications,
such as conference system, multi-functions hall. etc…
AUX channel has powerful mixing function, weight, gain, attenuation ratio parameters can be adjusted continuously. also with the automatic function of camera-tracking. threshold, level, attack&release time. etc… AEC automatic echo cancellation and system environment noise cancellation function,effectively eliminate environmental noise that generated by the feedback of pickup, moreover the noise of air Inside single generator(pink,white noise and 20~20K sine wave, amplitude adjustable ).
Front panel has level indicator for input/output ,USB port, RS232,485 and net ports remote control at rear panel. easy for user’s operations.
21 user presets can be save and recall, maximal 255 units can be link together via ID settings. password protection function for high level applications.

Front Panel

INPUT CHANNEL LEVEL INDICATORS
2 segment high precision level indicate lights show the current input channel level status.
OUTPUT CHANNEL LEVEL INDICATORS
2 segment high precision level indicate lights show the current output channel level status.
WORKING STATUS
USB, internet connection signal and power indicate lights.
USB INTERFACE
Used to connect with PC and center-control equipment, remote control.

Rear Panel

POWER SOCKET
AC~95-264V 50-60Hz.
POWER SWITCH
ETHERNET CONNECTION AND CONTROLLING PORT
Setting IP addresses to remote control by CAT-5 cable or WIFI control, also support internet control for long-distance application.
RS232/485
Realize remote real-time control of center-control device through Rs232, or control by one USB cord, link control by RS485.
SIGNAL OUTPUT CH1~CH8
SIGNAL INPUT CH1~CH8
AEC far IN and far OUT port
VCS IN is the input port for signals sent from the far port, and VCS OUT is the signal interface for signals sent to the far port.

PC Software

NOTICE: User manual, PC software are on the attached CD, due to the software upgrades time by time, please do control your DSP processor ONLY by this CD!

USB CONNECTION STEPS

Digital Matrix Processor

Click the PC software on the CD, press next step to continue according to the instruction until finish setup, then exit.
Connect the processor to the computer by USB, after power on the device, the computer will searching new hardware automatically, then it will show the message: hardware setup success and can be used.
Open PC controlling software, PC software will find USB and connection device, after this the online key change into green at the top right corner and show ” Online”, you can operate the processor by controlling software, Click “Online” button before exit.

PC Software Specifications

VOLUME CONTROLLING INTERFACE

Menu

File	download to the device.
Link	Input and output channels can be set freely to adjust all of the

parameter sad are.
Copy| Parameter copy freely between the input and Output channels.
Lock| Setting password of the panel to ensure the safety of the device.
Working Status| The working status could be set as; not memory ; immediate memory (under U01-21 user mode) , not memory but can be back to U01 mode when power on.
Setting ID/IP| To cascade control more than 254 device by setting different ID Setting IP address for Long-distance and wireless WIFI control.
Test Tone|
Channel Name| The whole channel name are revisable.
Sub Control| Any channel volume are revisable.
Group Control| Independent input and output 4 group control, can control different areas through the wall panel.
Language| Chinese and English language is switchable.

Spectrum Area: You can choose PEQ and phase freely which show the input and output channels.
The Volume Control Area:
Gain, Phase, Mute control for all input & output channels.
Preset Operation Area:
Save or recall preset parameter and show current preset parameter status.

NOISE GATE INTERFACE

Show threshold curve, level indicators and compression status for all channels.
Setting noise gate parameters for all input channels, the threshold is -90dB–20dB, start Time is: 1- 999ms, recovery time is 1-3000ms.

AGC CONTROL INTERFACE

Graph showing automatic gain changes and level indicator lights for all channels.
AGC control parameters of all input channels can be set: threshold value -60dB to 0dB, target level -60dB to 0dB, attack time 1-999ms, recovery time 10-3000ms, ratio 1:1.0-1:20-limit continuously adjustable.

COMPRESSOR INTERFACE

Show compression status level indicators and compression status of all channels.
Set the whole compression parameters for output channels, the compression range is -60dB–+20dB, ration is 1:1, 1:10, LIMIT, start time is: 1-999ms, recovery time is 1-3000ms.

DELAY INTERFACE

Show the delay parameter status of all channels.
Can adjust delay parameter of all channels, the scale is 0-680ms , there are millisecond, meter and feet units for choose.

MATRIX INTERFACE

Show connections of the device, users can enter and edit relevant channel by clicking the square button, every channel name is revisable.
All output channels can choose any input channels.

AUX CHANNEL INTERFACE

Select “Mag” interface, you can adjust the PEQ, High-cut and Low-cut parameters, select “PHASE” Interface, you can adjust the phase curve, also you can choose the non-current channel’s PEQ And phase curve to show in sync.
Adjustable Gain, Q, Frequency and Type for all PEQs, Bypass function is an option, we can choose PEQ style: Balance, High-shelf, Low-shelf, High-cut, Low-cut, Phase 180° or 360°of phase.
The Gain, Q, Frequency of PEQ can be adjusted by fader, and can be controlled by pressing the Up, Down, Left, Right key on the computer’s keyboard.
With compression adjusting fader on Aux channel, click” Set ” button, enter compression parameters setting: the compression range is: -90dB- +20dB,ration is 0,LIMIT,start time:0-999ms, recovery time: 0-999ms, the compression indicators be showed too.
. Auto-mixing ON/OFF switch, click “Set” button, enter auto-mixing parameters setting: Each input equipped with automatic mixer switch, and the microphone priority gain can be set independently, corresponding to the level display of each channel. The total volume can be controlled independently. Auto-mixing is gain – sharing, and the depth of attenuation ratio can be set separately.
Aux channels effect switch, click “Set” button, enter effect parameters setting, adjustable echo parameters for volume, repeat, delay, pre-delay. Adjustable reverb volume parameters for volume, reflect, time, pre-delay.and with a adjustment fader for whole effect of volume.
Camera tracking ON/OFF switch, click”Set”button,enter camera tracking parameters setting: choose the corresponding input channel which want to enter the camera tracking first(only the Chosen channel can enter to tracking channel),then choose the proper parameters of threshold (-50-0dB), start time (0-5000ms),recovery time(0-5000ms), when the any one channel signal is over the threshold, the channel will open automatically and camera start to track according to the Priority order from input ch A ~ ch H.
Input selection fader, can choose the input 1-8 channels to mix in Aux channels.
Aux’s Gain controlling fader, mute&level indicators.
ECHO cancellation ON/OFF, Click the “Set” key to enter the interface of echo cancellation volume control and noise reduction function. The microphone of echo cancellation input volume, and the far in and far out volume can be adjusted independently. Note that the local microphone volume is about the same as the far IN signal volume when used, so that the effect is best, and the VCS IN and AEC OUT volume can be adjusted appropriately for optimal handling IN different environments. NR noise reduction function is optional at 6-15dB. Note that there will be a certain delay after opening NR.

INPUT INTERFACE

Select “Mag” interface,you can adjust the PEQ,High-cut,Low-Cut for the input channel, select “PHASE” interface, you can adjust the current phase channel, also you can choose the non-current PEQ and phase curve to show in sync.
Adjustable Gain, Mute, Q , Frequency, Type for all PEQ, Bypass function is an option,we can choose PEQ style: Balance, High-shelf, Low-shelf, High-cut, Low-cut,180° or 360° of phase.
Left, Right key on the computer’s keyboard.
Low-cut frequency 20HZ-20KHZ is adjustable, you can choose slope rate : Butterworth, Bessel, the scale is: -6dB- -48dB.
High-cut frequency 20HZ-20KHZ is adjustable, you can choose slope rate : Butterworth, Bessel, the scale is: -6dB- -48dB.
Input can select the level of feedback inhibition, level 1-4 can be chosen.
The Gain, Mute, Phase of the input channels can be control separately, as same as the level display lights.

OUTPUT INTERFACE

Select “Mag” interface, you can adjust the PEQ, High-cut, Low-Cut for the output channels, select “PHASE” interface, you can adjust the current phase channel, also you can choose the non- current PEQ and phase curve to show in sync.
Adjustable Gain, Mute, Q, Frequency, Type of all PEQ, Bypass function is an option, we can choose PEQ style: Balance, High-shelf, Low-shelf, High-cut, Low-cut, Phase 180° , 360° of phase.
Left, Right key on the computer’s keyboard.
Low-cut frequency 20HZ-20KHZ is adjustable, you can choose slope rate: Butterworth, Bessel, Linkwitz-Riley, the scale is: -6dB- -48dB.
High-cut frequency 20HZ-20KHZ is adjustable, you can choose slope rate: Butterworth, Bessel, the scale is: -6dB- -48dB.
The Gain, Mute, Phase of the output channels can be control separately, as same as the level Display, lights.

Specifications

SPEC

| Frequency Response| 20Hz-20kHz,-0.3dB
---|---|---
Dynamic range|
THD| <0.005% at 1kHz(0dBu)
Crosstalk| >72dBu, 20Hz-20kHz
C.M.R.R| >78dBu 1KHz
MIC input| Type| Balance
Phantom power| +48V DC
Gain| 50dBu
Impedance| 2k ohm
Music input| Type| Balance
Gain| 35dBu
Max input level| +18dBu
Impedance| >10k ohm
Output| Type| Balance
Max output level| +18dBu
Impedance| <500Ω
Digital processing| 24bit sigma-delta A/D、D/A
32 bit DSP, 96kHz
AC POWER| AC 95V-264V 50/60Hz
| 48225444MM
| 2.7KG

Accessories

CD (Include PC software and user’s manual).
One USB cord.
One Power cord.

Rear panel control port connection

Ethernet connection port:you can choose to connect the computer by wire, connect several devices by switch, or use WIFI by router to control, but need to set different IP address and ID code for each device, otherwise, it might be can’t connect successfully due to the IP addresses conflict.
RS232 connection port: Central control and connect to PC through RS232 port.
RS485 cascade control port: link connect several devices by RS485, you can choose different ID to control separately. Contact multiple devices 480 port D+ and D- together, can cascade control for multiple machines after setting the machine with different ID Numbers.
AEC echo cancellation function operating instructions

Firstly, turn on the gain and phantom power of the input channel microphone.
Then choose AUX channel route to the output channel in the Matrix interface. Since AEC function is in AUX channel, AEC can be arbitrarily routed to the output channel (be careful not to direct the input channel to the output channel without AUX).
Finally enter AUX interface, choose to mixed with AUX channel input to the MIC channel at first, then open AEC switch ON, click the set key can enter the AEC echo cancellation after volume control interface, under normal circumstances without the echo can be eliminated, if echo cancellation effect is not ideal, can fine-tune VCS IN and the volume of the AEC OUT to match the level (note that MIC IN level also want as far into the volume of VCS IN fairly). NR is noise reduction function. If there is background noise (such as fan, air conditioner, etc.), it can be turned on and used. However, it should be noted that NR has a certain delay in noise reduction and the timbre of the local output is the same as that of the remote output.

232 communication protocol control code

Control Package Format

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Data1| Data2| Date3| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x40~0x5C| 0x??| 0x??| 0x??| 0x7D| 0x7B

Command Detail

Load Preset Matrix (0x40)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Factory/User| Preset| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x40| F: 0, U: 1| 0~12| 0| 0x7D| 0x7B

Example (Load Preset Matrix U02) : 7B7D01400101007D7B

Gain Control (0x41)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| In/Out| Channel| +/-| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x41| In:0 Out:1| 00~15| +: 0, -:1| 0x7D| 0x7B

Example (In1 Gain +) : 7B7D01410000007D7B

Mute Control (0x42)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| In/Out| Channel| No/Yes| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x42| In:0 Out:1| 00~15| No:0
Yes:1| 0x7D| 0x7B

Example (Out1 Un Mute) : 7B7D01420100007D7B

Load Preset Control (0x43)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Channel| HI-VOL| LO-VOL| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x44| 00~15| 0x??| 0x??| 0x7D| 0x7B

Example (Set In1 Volume +0.0dB) : 7B7D01440001187D7B

Output Volume Control (0x45

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Channel| HI-VOL| LO-VOL| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x45| 00~15| 0x??| 0x??| 0x7D| 0x7B

Example (Set Out2 Volume -3.0dB): 7B7D01450100FA7D7B

Sub Volume Control (0x46)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| In/Out| Gain| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x46| In:0 Out:1| 0~100| 0| 0x7D| 0x7B

Example (Sub Input Gain 90%): 7B7D0146005A007D7B

Sub Gain Control (0x47)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| In/Out| +/-| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x47| In:0 Out:1| +: 0, -: 1| 0| 0x7D| 0x7B

Example (Sub Input Gain+): 7B7D01470000007D7B

Get Now Gain (0x48)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| In/Out| Channel| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x48| In:0 Out:1| 00~15| 0| 0x7D| 0x7B

MCU Return: 1st Byte: In/Out, 2nd Byte = Channel, 3rd Byte: 0-80(-60~-20): 0.5dB/Step, 80-280(-20~0): 0.1dB/Step, 280-400(0~+12): 0.1dB/Step
Example (Read In1 volume parameter): 7B7D01480000007D7B

Get Now Mute (0x49)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| In/Out| Channel| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x49| In:0, Out:1| 00~15| 0| 0x7D| 0x7B

MCU Return: 1st Byte: In/Out, 2nd Byte = Channel, 3rd Byte: 0x00 or 0x01 = Un- Mute or Mute Example (Read In1 mute parameter): 7B7D01490000007D7B

Get Now Preset (0x4A)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| 0x30| 0x00| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x4A| 0| 0| 0| 0x7D| 0x7B

MCU Return: 0x00 ~ 0x0C = 0: F00, 1~12: U01~U12 Example (Read preset parameter): 7B7D014A0000007D7B

Get Now Sub (0x4B)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| In/Out| 0x00| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x4B| In:0 Out:1| 0| 0| 0x7D| 0x7B

MCU Return: 1st Byte: 0 ~ 100%, 2nd Byte = 0x00 or 0x01 = Un-Mute or Mute Example (Read Sub Input parameter): 7B7D014B0000007D7B

Sub Mute Control (0x4C)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| In/Out| No/Yes| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x4C| In:0 Out:1| No:0, Yes:1| 0| 0x7D| 0x7B

Example (Sub Output Mute) : 7B7D014C0101007D7B

Get Now Level (0x4D)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| In/Out| Channel| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x4D| In: 0,
Out: 1
Aux: 2| 00~15| 0| 0x7D|

0x7B

MCU Return: 1st Byte: In/Out, 2nd Byte = Channel, 3rd Byte: -128 ~ -1, 0~ +127dB = 0x80 ~ 0xFF, 0x00 ~ 0x7F
Example (Read In1 level): 7B7D014D0000007D7B
Example (Read Out1 level): 7B7D014D0100007D7B
Example (Read Aux level): 7B7D014D0200007D7B

Matrix Control (0x4E)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Channel| In| On/Off| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x4E| 00~15| 00~15| On: 1 Off: 0| 0x7D| 0x7B

Example (Out4 Matrix In2 On): 7B7D014E0301017D7

(16) Get Matrix (0x4F)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Channel| In| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x4F| 00~15| 00~15| 0| 0x7D| 0x7B

Example (Aux Gain): 7B7D01510200007D7B

Aux Mute Control (0x52)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Aux| 0x00| +/-| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x51| 0x02| 0x00| +:0,-:1| 0x7D| 0x7B

Example (Aux Mute): 7B7D01520200017D7B

(19) Aux Volume Control (0x53)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Aux| 0x00| No/Yes| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x52| 0x02| 0x00| No:0,Yes:1| 0x7D| 0x7B

Example (Aux Volume +0.0dB): 7B7D01530201187D7B

Volume Step Control (0x54)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Aux| HI-VOL| HI-VOL| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x53| 0x02| 0x??| 0x??| 0x7D| 0x7B

-60dB~-20dB: 2dB/Step, -20dB~+12dB: 1dB/Step Example (Volume): 7B7D01540000007D7B

Aux On Off Control (0x55)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| In/Out| Channel| +/-| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x54| In:0, Out:1| 00~15| +:0, -:1| 0x7D| 0x7B

Example (Effect On): 7B7D01550200017D7B
Example (Camera On): 7B7D01550201017D7B
Example (AutoMix On): 7B7D01550202017D7B
Example (ECHO On): 7B7D01550203017D7B
Example (Noise Redustion On): 7B7D01550204017D7B

Aux Ch Select Control (0x56)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| 0x02| Select| On/Off| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x55| 0x02| 1: Camera

2: AutoMix

3: AEC 4: NR

| 0:Off 1:Yes| 0x7D| 0x7B

Example (Aux In1&In3): 7B7D01560000057D7B
Example (Aux Camera In2&In4): 7B7D015601000A7D7B
Example (Aux Auto Mix In5&In6): 7B7D01560200307D7B

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Select| Ch 16~9| Ch 8~1| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x56| 0: AUX

1: Camera

2: Auto Mix

| Bit0 ~Bit7:

0:No

1:Yes

| Bit0 ~Bit7:

0:No

1:Yes

| 0x7D| 0x7B

FBQ Control (0x57)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| 0X00| Channel| FBQ| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x57| 0X00| 00～15| 0:OFF, 1~4: Level| 0x7D| 0x7B

Example (In3 FBQ Level3): 7B7D01570002037D7B (

Get Aux Now Gain (0x58)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Aux| 0x00| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x58| 0x02| 0x00| 0x00| 0x7D| 0x7B

MCU Return: 1st Byte: Aux/Effect, 2nd and 3rd Byte: 0-80(-60~-20): 0.5dB/Step, 80-280(-20~0):
0.1dB/Step, 280-400 (0~+12): 0.1dB/Step
Example (Get Aux Gain): 7B7D01580200007D7B

Get Aux Now Mute (0x59)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Aux| 0x00| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x59| 0x02| 0x00| 0x00| 0x7D| 0x7B

MCU Return: 1st Byte: Aux/Effect, 2nd Byte: 0x00 or 0x01 = Un-Mute or Mute Example (Get Aux Mute): 7B7D01590200007D7B

Get Aux On Off (0x5B)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| 0x02| Select| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x5B| 0x02| 1: Camera

2: AutoMix

3: AEC 4: NR

| 0x00| 0x7D| 0x7B

MCU Return: 1st Byte: Select, 2nd Byte: 0x00 or 0x01 = On or Off
Example (Effect Switch Parameter): 7B7D015B0200007D7B
Example (Get Aux Camera Switch Parameter): 7B7D015B0201007D7B
Example (Get Aux Auto Mixing Parameter): 7B7D015B0202007D7B
Example (Get Aux ECHO Parameter): 7B7D015B0203007D7B
Example (Get Aux Noise Reduction Parameter): 7B7D015B0204007D7B

Get Aux Now Ch Select (0x5C)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| 0x02| Select| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x5C| 0x02| 0:AUX

1:Camera 2:AutoMix

| 0x00| 0x7D| 0x7B

MCU Return: 1st Byte: Select, 2nd Byte: Matrix
Example (Get Aux Ch Select): 7B7D015C0200007D7B

Get Now FBQ (0x5E)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| 0x00| Channel| FBQ| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x5E| 0x00| 0~15| 0: off 1~4: Level| 0x7D| 0x7B

MCU Return: 1st Byte: Channel, 2nd Byte = Level
Example (Get In5 FBQ ): 7B7D015E0004007D7B

Get Full Matrix (0x61)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| 0x00| 0x00| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x61| 0x00| 0x00| 0x00| 0x7D| 0x7B

MCU Return: 1st Byte: Channel, 2nd Byte = Matrix, total 5 x 32 = 160 Bytes Example (Get Full Matrix code Parameter): 7B7D01610000007D7B

Get Group Parameter (0x63)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Group In1 Group Out4| 0x00| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x63| 0~7| 0x00| 0x00| 0x7D| 0x7B

MCU Return: 1st Byte: Channel, 2nd Byte: Volume, 3rd Byte: Mute, 4 th Byte = Matrix, total 2 Bytes Example (Get Group Parameter): 7B7D01630000007D7B

Group Volume Control (0x66)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Group In1 Group Out4| Gain| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x66| 0~7| 0~100| 0| 0x7D| 0x7B

Example (Input Group 2 Volume 90%)：7B7D0166015A007D7B

Group Gain Control (0x67)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Group In1 Group Out4| +/-| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x67| 0~7| + : 0, – : 1| 0| 0x7D| 0x7B

Example (Promote Output Group 3 Increasing Marshalling)：7B7D01670600007D7B

Group Mute Control (0x68)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Group In1 Group Out4| No/Yes| 0x00| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x68| 0~7| No: 0,Yes: 1| 0| 0x7D| 0x7B

Example (Output Group 4 Mute): 7B7D01680701007D7B

Group Matrix Control (0x69)

| 0| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---|---
DLE| STX| Device Address| CMD| Group In1 Group Out4| Ch 16~9| Ch 8~1| STX| DLE
Packet| 0x7B| 0x7D| 1～254| 0x69| 0~7| Bit0~Bit7: 0:No 1:Yes| Bit0~Bit7: 0:No 1:Yes| 0x7D| 0x7B

Example (Input Group 3 In 11& In13): 7B7D01690214007D7B
Mcu Will Return The “OK” For Correct Control Command: 0x4F 0x4B

Communicate Paramete

| Baud Rate| 115200| Stop Bit| 1
---|---|---|---|---
Data Bit| 8| Step| >=200ms
Parity| None| ID| Default 1

Safety Instruction

PLEASE READ THESE SAFETY MATTERS CAREFULLY BEFORE USE:

This product must make sure connect to the ground correctly. If it has broken down, to avoid any electric shock, the device power cord and plug both equipped safety ground connection. The power cord should according to the requirement to install and ground connection. Warning: Incorrect ground connection might be caused electric shock happen! If you have any inquiry about the ground connection, please let qualified people checking it or fix it, do not change it by yourself. If the power plug is unsuitable, you can entrust electrician or professional staff to install the suitable power plug.
To avoid the risk of injury, please close supervision when using the product near child
Please do not use the device at wet place, such as: near bathtub, washbasin, kitchen sink, wet basement or near swimming pool and lake.
It should not be placed near the device which filled with liquids such as the vase.
This product should install at draughty place or dry environment.
The power source type must be match to the operation instruction or the volts type which on the product
The product must keep away from heat source, such as: electric heater, electric blanket or other heat source products.
The product equipped one power cord that complied with safety certification. If you can’t insert the power cord into the plug, please contact electrician or professional staff to change the old plug. Attention that should not break the power plug safety device.
If the product not for operation for a long time. Please pull out the power cord from power plug. Don’t drag the power cord
This product use coupler as a make and break device, should be maintained convenient operation
Please don’t operate the product when following things opened, should call qualified people checking it or fix it: A. Power cord damaged. B. Objects or liquid get into the product. C. The product is sopping with rain. D. The product can not operate correctly or show obvious unusual. E.
The product dropped down, damaged.
Any inquiries about the product which not mentioned in the user manuals, please contact the eligible electrician or professional staff to repair.
Only apply to security use which area below altitude of 2000m.
Only apply to security use which condition except tropical climate.

Please do not let the heavy extrusion or stamp on the power cord, avoid by all pull or distort the power cord. To avoid the risk of ﬁre or electric shock, please do not use unqualiﬁed power cord.

Scan for more product information

ARS #AZ: 400 6828 333 16Н: 0752-6383950 #

SHE: xs@takstar.com
waL: www.takstar.com

Guangdong Takstar Electronic Co., Ltd.
Address: No. 2 Fu Kang YiRd., Longxi Boluo Huizhou, Guangdong 516121 China
Tel: 86 752 6383644
Fax: 86 752 6383952
Email: sales@takstar.com
Website: www.takstar.com