saxby lighting 99559 LALO Tilt LED Miniature Fixture Instruction Manual

: June 12, 2024
: saxby lighting

Table of Contents

saxby lighting 99559 LALO Tilt LED Miniature Fixture
Installation
Technical data
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

saxby lighting 99559 LALO Tilt LED Miniature Fixture

Thank you for purchasing this light ﬁtting. Please read the instruction carefully before use to ensure safe and satisfactory operation of this product. Please retain these instruction for future reference.

Warning
This light fitting is double insulated and does not require connection to an earth circuit.

Please read these instructions carefully before commencing any work.
This unit must be ﬁtted by a competent and qualiﬁed electrician.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off at the mains supply before installing or maintaining this ﬁtting. Ensure other persons cannot restore the electrical supply without your knowledge.
This light ﬁtting should be connected to a fused circuit.
If replacing an existing ﬁtting, make a careful note of the connections..
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

Plan the desired layout of these ﬁttings carefully, ensuring the cables will reach the distances between the transformer each light ﬁtting.
Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
The distance between units must be 0.5m minimum.
The unit must be located a minimum distance of 100mm from a joist.
The mains supply cable must have a minimum cross section area of 1.0mm2.
Cables must be protected using suitable conduit or plastic trunking.
This product must be mounted out of arms reach.

Installation

Existing fitting must be completely removed before installation of a new product. Before removing the existing ﬁtting, carefully note the position of each set of wires. Note that the switch is turned off before installation. The ceiling surface must be ﬂat and smooth to ensure a good ﬁt. After deciding the layout of the light fittings ensure that the cables are long enough to connect to desired positions.

Cut a mounting hole 45mm diameter in the ceiling taking care not to foul any pipes, mains cables or joists beneath the surface. It is always recommended to cut the hole slightly smaller than the size specified, and then file the hole until the recessed unit fits snugly.
Ensure a minimum ceiling void depth of 24mm is available.
Pull the mains wire through the hole and wire as detailed wiring.
Press the spring leaf and fit into the ceiling hole.
Push the unit up until firmly in position. Ensure that the product is fitted properly in the hole.
Adjust the tilt before switching on.
Replace fuse or circuit breaker and switch on. Your light is now ready for use.

saxby-lighting-99559-LALO-Tilt-LED-Miniature-Fixture-
FIG-1

Wiring
Having correctly identified the wiring from your existing light fitting, pull the mains wire through the hole and connect to the connection block inside the LED driver in the following way: saxby-lighting-99559-LALO-Tilt-
LED-Miniature-Fixture-FIG-2

Check that…
You have correctly identified the wires. The connections are tight. No loose strands have been left out of the connection block.

Technical data

Supply Voltage: 220-240 V~, 50 Hz
Bulb Type:
- 99559: 4W LED module (COB), 3000K This product contains a light source of energy efficiency class G.
- 99560: 4W LED module (COB), 4000K This product contains a light source of energy efficiency class F
Non-replaceable light source
Replaceable control gear by a professional
Conformity with all relevant UKCA Directive requirements.
Conformity with all relevant EC Directive requirements.
The power supply is double insulated and does not require connection to an earth circuit.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
This product is not suitable for dimming.

Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the ﬁnish. For your safety, always switch off the power supply before cleaning.