Snap One ES-SNDBR-2.1 Active Soundbar System Installation Guide
- June 6, 2024
- Snap One
Table of Contents
Snap One ES-SNDBR-2.1 Active Soundbar System
Installation Guide
The lightning flash with an arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electrical shock to persons.
The exclamation point, within an equilateral triangle, is intended to alert
the user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
-
READ these instructions.
-
KEEP these instructions.
-
HEED all warnings.
-
FOLLOW all instructions.
-
DO NOT use this apparatus near water.
-
CLEAN ONLY with a dry cloth.
-
DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions.
-
DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
-
DO NOT defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
-
PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
-
ONLY USE attachments/accessories specified by the manufacturer.
-
USE ONLY with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. -
UNPLUG this apparatus during lightning storms or when unused for long periods of time.
-
REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
-
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and objects filled with liquids, such as vases, shall not be placed on the apparatus.
-
To completely disconnect this apparatus from the AC mains, disconnect the power supply cord plug from the AC receptacle.
-
The mains plug/appliance coupler is used as a disconnect device, the disconnect device shall remain readily operable.
-
DO NOT overload wall outlets or extension cords beyond their rated capacity as this can cause electric shock or fire.
-
No naked flame sources, such as lighted candles, should be placed on the apparatus.
-
Correct Disposal of this product. This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.
To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling. -
This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to the electrical earth. (for wireless subwoofer unit)
WARNING: To reduce the risk of fire or electrical shock, do not expose
this apparatus to rain or moisture.
WARNING: No naked flame sources – such as candles – should be placed on
the product.
THIS PRODUCT CONTAINS A LITHIUM COIN CELL BATTERY. IF MISUSED OR ABUSED THIS
CAN RESULT IN:
• Smoke or gas hazard • Heat hazard • Fire hazard • Explosion hazard WARNING:
Do not place batteries in mouth or ingest.
Chemical burn hazard. Keep new and used batteries out of reach of children and
pets. If swallowed, it can cause severe internal burns in just 2 hours and can
lead to death.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
WARNING: If the battery compartment does not close securely, stop using
the product and keep it away from children and pets.
WARNING: Do not handle leaking or damaged Lithium batteries.
WARNING: Risk of leakage. Only use the specified type of batteries.
Never mix new and used batteries. Observe correct polarity. Remove batteries
from products that are not in use for extended periods of time.
Store batteries in a dry place.
WARNING: Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the like.
WARNING: Danger of explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type.
WARNING: Do not recharge non-rechargeable batteries.
WARNING: Avoid exposure to extreme heat or cold. Please dispose of any
used batteries properly, following any local regulations. Do not incinerate.
WARNING: Do Not Open! Risk of Electrical Shock. Voltages in this
equipment are hazardous to life. No user-serviceable parts inside. Refer all
servicing to qualified service personnel.
Place the equipment near a main power supply outlet and make sure that you can
easily access the power breaker switch.
WARNING: This product is intended to be operated ONLY from the AC
Voltages listed on the back panel or included power supply of the product.
Operation from other voltages other than those indicated may cause
irreversible damage to the product and void the product’s warranty. The use of
AC Plug Adapters is cautioned because it can allow the product to be plugged
into voltages in which the product was not designed to operate. If the product
is equipped with a detachable power cord, use only the type provided with your
product or by your local distributor and/or retailer. If you are unsure of the
correct operational voltage, please contact your local distributor and/or
retailer.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
EU COMPLIANCE INFORMATION
Eligible to bear the CE mark; Conforms to European Union Low Voltage Directive
2006/95/EC; European Union EMC Directive 2004/108/EC; European Union
Restriction of Hazardous Substances Recast (RoHS2) Directive 2011/65/EC;
European Union WEEE Directive 2002/96/EC; European Union Eco- Design Directive
2009/125/EC; European Union Registration, Evaluation, Authorization, and
Restriction of Chemicals (REACH) Directive
2006/121/EC; European Union Radio and Telecommunications Terminal Equipment
(R&TTE) Directive 1999/5/EC.
This product contains batteries that are covered under 2006/66/
EC European Directive, which cannot be disposed of with normal household
waste. Please follow local regulations.
You may obtain a free copy of the Declaration of Conformity by contacting your
dealer, distributor or worldwide headquarters.
WEEE NOTICE
Note: This mark applies only to countries within the European Union (EU) and
Norway.
This appliance is labeled in accordance with European Directive 2002/96/EC
concerning waste of electrical and electronic equipment (WEEE). This label
indicates that this product should not be disposed of with household waste. It
should be deposited at an appropriate facility to enable recovery and
recycling.
Federal Communication Commission Interference Statement This device complies
with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Approved under the verification provision of FCC Part 15 as a Class B Digital
Device.
Caution: Changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate this device.
Caution: To comply with the limits of the Class B digital device,
pursuant to Part 15 of the FCC Rules, this device is to comply with Class B
limits. All peripherals must be shielded and grounded. Operation with non-
certified peripherals or non-shielded cables may result in interference to
radio or reception.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
Note: The country code selection is for non-US models only and is not
available to all US models. Per FCC regulation, all WiFi products marketed in
the US must fixed to US operation channels only.
This Class B digital apparatus complies with Canadian ICES-003. CAN ICES-3
(B)/NMB-3(B)
WIRELESS TRANSMITTER COMPLIANCE INFORMATION
The term “IC:” before the radio certification number only signifies that
Industry Canada technical specifications were met.
This device complies with part 15 of the FCC Rules and the applicable Industry
Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference, including interference that may
cause undesired operation of the device.
This equipment complies with FCC and IC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
INTRODUCTION
Thank you for purchasing Episode speakers. To complete installation, follow these instructions. Visit our website for design recommendations and speaker calculators.
CONTENTS
• 1x Soundbar | • 1x RCA cable |
---|---|
• 1x Subwoofer | • 1x Toslink cable |
• 2x Power cords• | • 1x Remote |
• 1x Wall bracket | • 4x Wall Anchors |
FEATURES
Sound Bar (Front)
A. Source LED
Blue: Bluetooth input
Red: Standby
Blink Once: Volume level at min/max
Blinks Continuously: Muted
Green: Toslink optical input
Yellow: RCA Line Level Input
Purple:
Blink Once: EQ off;
Blinks Twice: EQ on
White:
Blink Once: Volume level changed
Blinks Twice: Dolby Digital source being decoded
B. Input Toggle Switch between digital, analog, and Bluetooth inputs
C. Volume Up Increase volume level
D. Volume Down Decrease volume level
E. Mute No volume
Note: This soundbar is equipped with Audio Sense which will enable the
soundbar to turn on when an audio signal is detected.
Soundbar (Rear)
A. RCA Line Level Input 2 Left and Right RCA stereo input
B. Toslink Optical Input 1 Digital optical input. Dolby Digital formats
will be decoded
C. DC Power In Power cord connection
D. Master Power Switch ON/OFF switch
Subwoofer
A. STATUS LED
Red: Standby
Blue: On
B. Volume Knob Adjust the master volume
C. Master Power Switch ON/OFF switch
D. AC Power In Power cord connection
Remote
A. ON | F. EQ ON |
---|---|
B. Input 1 Toslink optical output | G. OFF |
C. Volume Up Increase volume level | H. Bluetooth Press to access pairing menu |
D. Volume Down Decrease volume level | I. Input 2 RCA line-level input |
E. Mute No volume | J. EQ OFF |
SETUP
Soundbar Placement
Placement should be below a flat-screen TV on a cabinet top or shelf for most
applications. Other options for placement include on-wall using the included
bracket, or attached to a flat panel mount using the optional Strong mount
bracket.
Installing On or In a Cabinet
Note: When placing the soundbar on a cabinet shelf, the front edge of the
speaker should be flush with the front of the shelf. Placing the speaker
further back on the shelf will degrade the sound quality of the speaker.
Mounting on a Wall
Considerations for Wall Mounting
Installing the soundbar more than 3″ from the screen may delay the audio from
the video and provide a poor listening experience. The soundbar should be as
close to the TV as possible for the best listening experience.
Attaching the Wall Bracket
-
Mark the position of the bottom of the TV.
-
Mark the position of the TV’s center point.
-
Remove the TV from the mount if necessary.
-
Locate wall studs using a stud finder (not included).
-
Place the bracket on the wall with the flat side toward the wall and the notched center mark facing up. The Soundbar center mark should be located at the center point of the installed television.
-
Position the bracket vertical center “V” groove 2-1/8 ” from the bottom of the TV. The Soundbar will hang flush with the bottom of the TV once installed.
-
Level the bracket and attach it to the wall studs using the horizontal screw-hole slots. Use all 4 screws and keep the bracket securely attached and flush with the wall.
Note: If wall studs cannot be used, wall mollies or anchors with the appropriate weight rating for the soundbar should be used. -
Clip the Soundbar onto the bracket, and center by adjusting left to right.
Installing on a Flat Panel Mount
The Episode 2.1 Soundbar can be mounted directly to a Flat Panel Mount with
the Strong™ SM-SBAR-BKT (available separately). Using the Flat Panel mount
bracket allows the Soundbar to move with the TV when mounted to articulating
arm mounts. This provides an optimal listening experience for these
installations.
Subwoofer Placement
Subwoofer placement can have an effect on performance. All rooms are
different, but the strongest output will likely occur if the subwoofer is
placed in a corner of the room on the same wall as the soundbar. This is
known as the boundary effect and will emphasize certain bass frequencies while
canceling others. Some listeners find this to be the best-sounding result,
while others find it “boomy” or muddy. Experiment with available placement
options and use the tuning instructions in the FINE TUNE section of this
manual.
Programming the Remote
- Connect power to the soundbar, then press the power button.
- Press and hold MUTE on the soundbar until the LED flashes yellow.
- Press the button on the soundbar that will be programmed once (MUTE, VOLUME UP, VOLUME DOWN). LED will now be solid yellow.
- Press the button to be learned on the TV remote (MUTE, VOLUME UP, VOLUME DOWN) slowly four times (look for the LED to flash before pressing again).
- LED will now blink green 6 times.
- Repeat for MUTE, VOLUME UP, VOLUME DOWN commands.
Remote Codes
Please visit the support tab of the product page for more information and
available HEX codes.
Command | NEC Code |
---|---|
ON | 13EC-00 |
OFF | 13EC-80 |
IN1 | 13EC-C0 |
IN2 | 13EC-40 |
Bluetooth | 13EC-03 |
Volume + | 13EC-E0 |
Volume – | 13EC-D0 |
Mute | 13EC-F0 |
EQ On | 13EC-08 |
EQ Off | 13EC-28 |
CONNECT
Use included RCA or Toslink cable to connect devices. Once connected, Audio
Sense will enable the soundbar to turn on when an audio signal is detected.
The unit enters standby mode if no signal is detected after 15 minutes.
CAUTION: All connections and switching must be done with the device turned
off. Connect power last to ensure the device is off during all setup and
connections.
Bluetooth Pairing
- Use the soundbar remote to select the Bluetooth input.
- Access the Bluetooth pairing menu on the device to be paired to the soundbar, by pressing the Bluetooth button.
- Select “Episode 2.1 Soundbar“.
- Wait until the device display reads “Connected”.
- Select the audio output options, and select the “Episode 2.1 Soundbar”.
Note: Changing inputs requires device reconnection.
Sub to Soundbar Pairing
Turn both units on, then press and hold both hidden buttons using a push pin
or other fine point until the subwoofer powers on (Blue LED).
Press and Hold to Pair
Factory Reset
The unit must be in standby mode. Press VOL down and MUTE until LED flashes 5
times.
FINE-TUNE
Subwoofer Level
After making all connections and calibrating the speakers, set up the
subwoofer using the following steps:
- Connect power to the subwoofer. The status LED will illuminate solid red when power is present and the subwoofer is on. LED will illuminate solid blue when the soundbar is on.
- Set volume dial at 50%.
- Play a movie scene or music track and set the system volume to an average level. Listen to the bass level from the listening position.
- Adjust the subwoofer VOLUME control as desired.
EQ
The EQ is set to bring out the dialog to replicate a 3 channel setup with only two channels. Determine the best system settings using the following steps:
- Play a movie scene during an acoustically chaotic scene and set the system volume to an average level with the EQ off. Listen to the dialog from the listening position.
- Listen to the same scene with the EQ on.
- Repeat steps 1 & 2 until the preferred setting is determined.
SPECIFICATIONS
Tweeter | Two – .75″ Soft Dome |
---|---|
Woofer: | Four – 3″ Polypropylene |
Subwoofer: | 8″ Polypropylene |
Color: | Black |
Power Handling (Peak): | 250W |
Frequency Response | 35 Hz – 20 kHz |
Auto On (Audio sense) Sensitivity | 4mV |
Input Power (Soundbar): | 100-240 VAC, ~50/60 Hz, 1.8A |
Input Power (Subwoofer): | 100-240 VAC, ~50/60 Hz, 90W |
Inputs: | Digital Optical, RCA, and Bluetooth Inputs |
Subwoofer Adjustments: | Volume, On/Off |
Weight (Soundbar): | 7.6 lbs |
Weight (Subwoofer): | 21.2 lbs |
Grill Type: | Acoustically Transparent Cloth |
Soundbar Finished Dimensions | 4.51″ H x 43.9″ W x 3.08″ D |
Soundbar Finished Dimensions incl Wall Mount Bracket | 4.51″ H x 43.9″ W x |
3.33″ D
Subwoofer Finished Dimensions| 9.88″ W x 11.57″ H x 12.96″ D
Subwoofer Finished Dimensions incl Volume Knob| 9.88″ W x 11.57″ H x 13.53″ D
Sold As| Each
WARRANTY
10/2-Year Limited Warranty
Episode® Active Products have a 2-Year Limited Warranty for amplifiers and a
10-year warranty for all other components. This warranty includes parts and
labor repairs on all components found to be defective in material or
workmanship under normal conditions of use. This warranty shall not apply to
products that have been abused, modified or disassembled. Products to be
repaired under this warranty must be returned to a designated service center
with an assigned return authorization (RA) number. Contact technical support
at support@episodeaudio.com for an RA
number.
CONTACTING TECHNICAL SUPPORT
866.838.5052
support@episodeaudio.com
© 2017 Episode®
Rev: 170516-0515
Documents / Resources
| Snap
One ES-SNDBR-2.1 Active Soundbar
System
[pdf] Installation Guide
BLKSUB8, 2AJAC-BLKSUB8, 2AJACBLKSUB8, ES-SNDBR-2.1 Active Soundbar System,
Active Soundbar System
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>