AENO HD2 Hair Dryer User Guide
- July 17, 2024
- AENO
Table of Contents
Quick Start Guide
Hair Dryer HD2
(Models: AHD0002, AHD0002-UK)
v1.0.2111.06.2024
HD2 Hair Dryer
AENO ™ Hair Dryer is designed for drying and styling hair.
Models: AHD0002 (Plug Type E), AHD0002-UK (Plug Type G).
Technical Specifications
Power supply (input): 220–240 V (AC), 8.3 A, 50–60 Hz. Power: 1,700.0–2,000.0
W.
Motor speed: up to 20,000 rpm. Number of operating modes: 4. Noise level (at a
distance of 50 cm): ≥ 67 dB. Ionization function. Overheating protection.
Power cord length: 1.7 m. Color: Grey. Casing material: ABS plastic. Nozzle
material: polycarbonate. Device dimensions without the nozzle (L×W×H):
162×78×270 mm. Nozzle dimensions (diameter × height): 65×45 mm. Operating
conditions: temperature 0…+40 °C, RH < 80 % (non-condensing). Storage
conditions: temperature −10…+50 °C, RH < 80 % (non-condensing). Scope of
Supply (see Fig. A)
AENO™ Hair Dryer, concentrator nozzle, travel bag, Quick Start Guide.
Device Elements and Accessories (see Fig. A)
- concentrator nozzle,
- Cool Shot button,
- operating mode switch,
- handle
- air inlet grille,
- power cord,
- travel bag.
Limitations and Warnings
This device is not intended for use by children under the age of 14 or by
persons with reduced physical, mental or intellectual abilities unless they
have sufficient experience and knowledge of how to use the device and are
supervised by a person responsible for their safety. The device is intended
for use in domestic environment only. Do not use the device outdoors.
ATTENTION! Do not use in areas with high humidity or places with a high risk
of the device falling into water. Unplug the device immediately after use.
If you have any questions or difficulties in using your AENO™ device, please
e-mail support at support@aeno.com or chat with us
online at aeno.com/service-and-warranty. The specialists will help you solve the problem, and you will not
have to waste time and effort visiting the store. not leave the device
unattended while it is plugged in. If the device has been transported or
stored at low temperatures, leave it at room temperature for 2 hours before
use. Do not drop or throw the device. Do not use a device that is damaged or
has previously fallen into water. Do not allow children to play with the
device. Connect the device directly to the mains, do not use extension cords.
Disconnect the device from the mains by grasping the plug, not the power cord.
Make sure that the rated voltage and frequency indicated in the technical
specifications correspond to the parameters of the electrical network. Handle
the device with dry hands only. Do not cover the air inlet grille (5) while
using the device. Make sure that the power cord (6) does not get twisted, bent
or pressed by anything, and does not come into contact with hot objects or
heat sources. Clean the device only after unplugging it and letting it cool
down completely. Do not wash any part of the device under running water. Do
not use chemical and aggressive detergents, abrasive pastes, products
containing acids and solvents or metal sponges for cleaning. Use original
accessories only. A detailed description of the device, its modes and
functions can be found in the complete User Manual available at
aeno.com/documents. Intended Purpose of the
Concentrator Nozzle
The concentrator nozzle (1) gathers air into one powerful stream. Recommended
for drying and styling hair.
Operating Modes of the Device
Symbol | Description |
---|---|
Powerful hot airflow | |
II | Powerful warm airflow |
I | Weak warm airflow |
Cool airflow |
Functions of the Device Controls
Element | Action | Meaning |
---|---|---|
Slide up/down | Switch operating modes, switch off the device (O) | |
Press and hold | Activate Cool Shot |
Preparing the Device for Operation
- Carefully open the packaging and remove the device and its accessories. Remove any packaging materials.
- Carefully straighten the handle (4) of the device as shown in Fig. B.
- Clean the device and nozzle (see “Cleaning and Maintenance”).
Operating Instructions
-
If you need to use the nozzle, attach it to the device until it clicks into place (see Fig. C). The device can also be used without the nozzle.
-
Insert the plug of the power cord into a socket.
-
Turn on the hair dryer by moving the switch (3) to the required position (see “Operating Modes of the Device”).
Note. The ionization function is activated automatically each time the device is switched on. -
Dry the hair. Style it, if necessary.
-
Move the switch to the O position.
-
Unplug the device.
Cleaning and Maintenance
Cleaning the casing and nozzle. Wipe the casing of the device and nozzle with
a soft cloth dampened in clean water, then wipe dry.
Cleaning the air inlet grille and filter. The purpose of the grille and filter
is to trap dust and hair that may enter the device during operation and
storage.
Cleaning should be performed every 2–4 weeks to maintain stable operation of
the device. Perform the cleaning by following the steps below (see Fig. D):
- Remove the air inlet grille.
- Clean the grille and filter with a soft, dry cloth.
- Reinstall the grille.
Troubleshooting
- The device does not turn on. Possible causes: the socket is defective; overheat protection has been triggered. Solution: check if the socket is working correctly by plugging another device into it, if necessary connect the device to a working socket; unplug the device and let it cool down completely.
- The airflow is weak. Possible causes: the wrong operating mode is selected; foreign objects are present in the nozzle. Solution: choose the desired mode with the switch; unplug the device, let it cool down completely, then remove and clean the nozzle.
- The airflow is not hot enough. Possible cause: the wrong operating mode is selected. Solution: choose the desired mode with the switch.
ATTENTION! If none of the suggested methods have solved the problem, contact your supplier or an authorized service centre. Do not disassemble the device or attempt to repair it yourself.
ASBISC reserves the right to modify the device and to make changes and
additions to this document without prior notice to users.
The warranty period and service life is 2 years from the date of retail sale
of the device. Manufacturer: ASBISC Enterprises PLC, Iapetou, 1, Agios
Athanasios, 4101, Limassol, Cyprus. Made in China. All trademarks and brands
mentioned herein are the property of their respective owners. The date of
manufacture is indicated on the package. Up-to-date information and a detailed
description of the device, as well as connection instructions, certificates,
information on companies that accept quality claims and warranties are
available at aeno.com/documents.
Recycling information This symbol indicates that you must follow the
Waste Electrical and Electronic Equipment (WEEE) and Waste Battery and Battery
Regulations when disposing of the device, its batteries and accumulators, and
its electrical and electronic accessories. According to the rules, this
equipment must be disposed of separately at the end of its service life. Do
not dispose of the device, its batteries and accumulators, or its electrical
and electronic accessories together with unsorted municipal waste, as this
will harm the environment. To dispose of this equipment, it must be returned
to the point of sale or turned in to a local recycling facility. You should
contact your local household waste disposal service for details.
Device name: ____
Serial number: ____
Purchase date: ___
Seller stamp:——————-
Download the full warranty card on aeno.com ARA
aeno.com
Please contact our online support team if you have any questions or issues
with your AENO device.
This is a better option than visiting the store and will save you time and
effort
https://aeno.com/service-and-warranty
Get Support
aeno.com/service-and-warranty
aeno.com/documents
Documents / Resources
| AENO
HD2 Hair
Dryer
[pdf] User Guide
HD2, HD2 Hair Dryer, HD2 Dryer, Hair Dryer, Dryer
---|---
References
- Home appliances AENO - Smart home appliances on the official website of the manufacturer AENO in Europe
- Service and Warranty | AENO in Europe
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>