WOODBRIDGE WH01-1 Elongated 1-Piece Toilet Instruction Manual

WOODBRIDGE WH01-1 Elongated 1-Piece Toilet

Product Specifications

• Dimensions: 37-1/2″(955mm) x 17-3/4″(452mm) x 10-1/2″(268mm)
• Weight: 4-3/4″(122mm)
• Power Cord Length: 1.5m
• Power Requirements: 300mm x 300mm
• Outlet: Sewage outlet 305/400mm

Product Usage Instructions

Installation Guide

1. Confirm that the power socket used is handled by proper grounding.
2. The length of the power cord is 1.5m, and the location of the socket should be close to this product to facilitate installation and removal, and as far away from the bathtub as possible.
3. It is recommended to use a waterproof type socket, do not use an extension cord to connect this product.

Placement
Install the product against a finished wall with the following dimensions: 5-7/8″, 12″, 17-3/4″, 9-7/8″, 25-5/8″, 15-5/8″.

FAQ

• Q: What should I do if the dimensions vary slightly from the manual?
  

  • A: Dimensions may vary by up to 3/8. It is recommended to pull all dimensions of the actual model for installation and measuring purposes.

USER MANUAL
Immax NEO LITE travel charging station
for electric cars EV/PHEV AC Type 2 22kW Tuya

NSE003

TECHNICAL SPECIFICATION

• Working voltage: 380V~480V AC (3 phases)
• Operating current : 32A (3 phase) max
• Overvoltage protection: 265V (1 phase voltage)
• Under voltage protection: 175V (1 phase voltage)
• Overcurrent protection : ≥110% rated current
• Leakage protection : AC/A+DC6mA
• Ground fault protection : Yes
• Lightning protection: Yes
• Water resistance: IP67 Type 2 connector / IP54 charger / IP44 CEE industrial plug LCD: 2.8“ display
• Power supply : 22KW Max
• Operating temperature : -25°C~+55°C
• Operating humidity : 5% ~ 95%
• Working altitude : <2000m
• Communication mode : Wifi / Bluetooth / TUYA
• Connector type : Type 2 / Mode 2
• Overheat protection : Yes
• Cable harness : 56mm2 + 10.25mm2
• Cable length : 5m

GENERAL INSTRUCTIONS
This manual contains important safety instructions, please read before using the charger. Please keep these instructions. This manual must be considered an integral part of the device and must always be available to all who come into contact with the device. The manual must always be attached to the device, even when handing it over to another user.

Intended use
This product is intended for occasional CHARGING of electric vehicles. It is not intended for permanent charging.

SPECIFICATION

• Chargers for electric cars generally do not require daily or regular maintenance. Wipe the charger with a soft dry cloth.
• Do not use water, caustic chemicals or aggressive cleaning agents. Disconnect the device from AC power before cleaning.
• Make sure the EV charger is stored in a dry place.

WARNING

• Please read all instructions in this manual before using this product.
• Children should be supervised when near the charger while it is plugged in. Do not place the EV charger near explosive, flammable materials, chemical fumes, or potentially hazardous materials.
• The product must be grounded. Should it fail or malfunction, grounding provides a path of least resistance for electrical current, reducing the risk of electric shock. The device detects the presence of proper grounding and will not work if it is disconnected.
  • Do not use the charger with a damaged output cable, charger connector or module.
  • Do not disassemble the internal components of the EV charger without permission, this will void the warranty.
  • Always position the charger output cable so that it cannot be walked on, stepped on or tripped over, damaged or otherwise stressed.
  • Unplug the charger before cleaning it. To clean the charger, wipe it with a clean cloth dampened with water or a mild solution of detergent suitable for use on automotive parts. Do not use chemicals or solvents.
  • Do not submerge the control box or charging connector in water.

PRODUCT DIAGRAM

QUICK CHARGING GUIDE

1. Plug the charger into the socket correctly
2. Double-click to set the required current (amps).
3. Connect to the vehicle

LIGHT INDICATOR

Green on – Connected – Charger connected

Green Blinking – Connected – The charger is properly connected to your vehicle

Blinking Blue – Charging – The charger is charging your vehicle

Blue – Full Charge – Your vehicle is fully charged

Manufacturer and importer: IMMAX, Pohorie 703, 742 85 Vresina, EU www.immax.cz
Designed in the Czech Republic, made in China

USER MANUAL

1. Insert the plug into the outlet to turn on the device, but do not put the charging gun in the car yet. The screen lights up. The bottom of the screen
   will show „idle“ (inactive) green, indicating that charging has not started. The operation light (function button) will also be green.

2. Press the function button for 3 seconds to enter the function menu. The following options will appear in the menu: Time reservation – scheduled charging (timer), Change current – selectable value of the charging current, Ground Protection – overvoltage protection and Ungrouped use – without overvoltage protection, Release wifi – turning on the WiFi connection. The selected function will be highlighted in purple. Click to move to the next item, a long press selects the selected function.

3. To set the charging current, press the function button for 3 seconds to enter the function menu. Click repeatedly to move to Change current, long press the function button to open the charging current setting menu, and click repeatedly to select one of the current values 32/16/13/10/8A. After selection, press the function button for 3 seconds to confirm the charging current and return to the home screen. The selected current value will appear on the display.

4. To set the scheduled charging (timer), press the function button for 3 seconds to display the function menu. Click to move to the Time reservation option, long press to open the time setting, and short press again to set the charging time delay in the range of 1 to 6 hours. After selection, press the long function button to confirm the scheduled delay of the start of charging and return to the home screen. Delay… will appear on the display and the time until the start of charging will start counting down. If you press the function button again for 3 seconds, the timer function will be cancelled.

5. After setting, insert the charging connector into the electric car. The function button will flash blue, Connect… will appear at the bottom of the screen, which means charging the electric car. When fully charged, the function button will light blue and the display will show Charger Finish.

TUYA APPLICATION
Users will be able to easily control and monitor charging of your electric car via the Tuya app. Access to features such as charging schedules, charging records and statuses, personalized for each user.

Note: Tuya application instructions are subject to change due to reason updates that may change its interface and functions, as well as vary depending on the devices used.

Download the app by searching for “Immax NEO PRO in Apple Store / Play Store or by scanning the QR code below to download.

REGISTRATION / LOGIN
Using an existing account

After downloading the app, you can register a new account or sign in using existing account. Click Register, you will see the Tuya Privacy Policy, click Agree and go to Tuya page, click Agree button and go to the registration page using your mobile phone number or email addresses.

Enter your mobile phone number or email address.
You will receive a verification code in your email.

If you already have an account, select „Sign in with an existing account“ and enter in the application.

CONNECTIVITY
Enable Bluetooth and Wifi in the app to enable communication with your device.

ADD DEVICE
You can add a device by clicking „Add Device“ or by clicking „+“ on the top. (turning on Bluetooth makes it easier to find a device or other fast adding a device).

Note: In case of failure or search timeout check if the smartphone is connected to the WiFi network and the router is working in the 2.4 GHz frequency band, or if the Bluetooth connection failed due to the smartphone being too far from the charging station.

CONTROL
Access to device features and management.
Click on the icon of the device you are looking for to enter the control interface devices. When you connect for the first time, a standard selection menu will appear. You can choose standard mode and adjust the charging time or choose manual mode. If you choose the second of the listed modes, charging will begin when your vehicle is connected.

CHARGING MODE

1. Manual mode: control the charger by turning it on and off in the app.

2. Plan: programmed charging.

3. edit

4. charging mode

5. charging status

6. power on/off

7. charging mode

8. total power value

9. voltage value

10. current value

11. power value

12. main page

13. records

14. settings

ACTIVITY RECORD
You can view charging record, charging time, charged power and more. Note: Only information that is turned on or off through the app and recorded in the charging log will be displayed.
When charging is activated with the button, the charging log is not recorded.

Please read the user manual carefully before using the product and keep it for further use. Use the lamp in accordance with the instructions. If you have a question or if you need advice, contact us at podpora@immaxneo.eu

• Manufacturer and importer: IMMAX, Pohorie 703, 742 85 Vresina, EU
• www.immax.cz
• Designed in the Czech Republic, made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>