Hand Showers E035 shower head Installation Guide
- June 7, 2024
- Hand Showers
Table of Contents
Model: E035
Installation instructions of shower head
| 
---|---
| 
| 
---|---
Handwheel
Note, the installation of the shower panel of different model is the same. only the appearance of the product is updated
Read Before Using Your New Shower Panel
Congratulations on purchasing our Show” Panel. Your new will be a great
addition to your bathroom for years to corn This man I will our reference for
installation, instructions for care of the shower panel. o all to shower panel
and for the benefits of using our Shower Panel.
Before using our Shower Panel. please read this document carefully and
thoroughly. The instructions and safety information in this document is
essential to the safe operation of your new unit. Additionally, not adhering
to the conditions regarding maintenance and installation in this document may
affect your new product’s warranty.
Our luxury Shower Panel brings a spa experience into your life in the comfort
of your personal bathroom. Adding the shower panel as a modification to your
present shower will allow you to enjoy the pleasures of massaging body spray
jets. an overhead rain shower and a shower wand. Furthermore. the shower panel
will operate with your existing plumbing supply lines with standard line
pressure and flow rates.
< Instructions for Installation >
Carefully read and follow the instructions in the following guidelines. If you
fail to follow these recommended instructions and techniques for installation,
you risk affecting the warranty claims for your product and causing damage to
the unit and the surrounding area.
IMPORTANT.
In order to install this shower panel, a simple understanding of plumbing
techniques will be necessary. Please contact your dealer or a professional
plumber if you are unfamiliar with plumbing techniques or have questions.
While determining the installation location for your new un account the
guidelines below. All installations are unique you take into are general.
- This shower panel is the deed for indoor use ONLY. It is not or outdoor use or other uses
- We have provided flexible so ply his It is recommended that you consider installing individual pI off valves for the cold and hot water supplies.
Prior to instaIlation. please make sure your package is complete and your unite is not damaged. of the unit’s components. Check for damaged and broken components and sections. Contact your dealer or the manufacturer if you find damaged sections.
Tools needed
Plumbing Requirements.
-Flow rate, 2.5 gallons per minute (GPM)
-Water pressure. 60 to 80 psi for both cold and hot supply lines
You will have to speak with a plumber regarding the installation of a booster
pump or enlarging your supply lines if your water supply is unable to meet the
requirements above.
< Mounting the Brackets of the Shower Panel >
While mounting the brackets of your new shower panel. t decision on which
height to mount it at, be mounted at way, various
-It is recommended that the shower pat be accessible to people of varying all heights. shower panel.
-A comparison between the height of the cad ower to the body jets and the height of all of the people who will be using sho and.
-Whether or not the height you choffwill allow the shower panel to completely cover up the connection points for the cold and hot water supplies.ln order to determine your installation location of the shower panel. you will require the use of a tape measure and pencil or some type of marking tool).
IMPORTANT. Check the condition of the wall and the electric wires before
drilling)
STEPS.
Steps for Mounting the Shower Panel
a.Two mounting brackets are used in units with two single bar straps. (one
will go on the top strap and one will go on the bottom strap.)
b.Determine the distance between the top and bottom strap. Determine the
distance between the most outside measurement from the bottom of the top strap
to the bottom of the shower panel. Mark them on the mounting wall. The
distance between two straps can determine the mounting locations of two
mounting brackets.
c.Hold one mounting bracket flat against the wall with the mounting holes over
the mark indicating the bracket’s location from the centerline. The mounting
holes must point towards the bottom of the shower.
d.You will have to line up this mounting bracket so that the bend in the
bracket is on the horizontal line. Meanwhile. make sure the mounting holes are
still centered on the mark you made for the bracket’s location
e.Mark the two screw holes location with the pencil.
f.Drill each hole location with 5/ I6 diameter drill bit.
TIP. Pilot drill with a smaller drill bit before stepping up to the final
size of your wall surface is prone to chipping and cracking.
g.Place the wall anchors into the mounting holes you just drilled.
h.With a Phillips screwdriver. or a drill with a Phillips •it, attach the mo
ing brackets to the wall surface with the use of the provided screws.
< Connect Your Shower Panel to Your Water Supply>
After installing mounting brackets your shower panel water connections will be
made.
-
You will find the cold and was sections on the back of the shower panel. The cold connection is labeled with I blue/yellow slicker and thehot connection is labeled with a red sticker.
-
Connect each hose to the corresponding cold and hot water supplies. Tighten both hoses.
IMPORTANT. Use the rubber washer included in your purchase. -
Turn on each of the valves if you installed cut-off valves on your supply line. Check for leaks in both the cold and hot water supply. If there are no leaks, you may move on to the next process in the installation.
IMPORTANT:
- Before installing the shower panel. Please clean the water supply valve with water for 5 minutes. Otherwise. it is very easy to block the generator and affect the work of LED lights and display.
- Please make sure the hose does not twist when h the panel on the wall.
| 
---|---
- Install hand shower cradle( 1)to the shower panel by installing the rubber washer(Z)and the locking nut(3)and attach white plastic hose tube connector(5)with PVC tubing to complete the connection. (NOTE.Make sure the silicon gasket(4)is seated properly inside the connector.)
- Connect the tub spout(l)to the shower panel with the rubber washer (2)and the locking nut (3)and attach a plastic hose connector(5)with PVC tubing to complete the connection.
NOTE, Make sure the silicon gasket(4)is seated properly inside the connector
-Make sure the water supply hose is to the hot water valve. Tlie mixing valve will not function properly if the s hoses are installed incorrectly.
- Put your shower panel on the wall surface with the mounting straps above the corresponding mounting brackets while making sure that the flexible supply lines are in the shower panel enclosure.
- Slide the shower panel down. Stop when it rests on the mounting brackets you installed. The shower panel must be seated onto the mounting brackets by pulling down on the shower panel. You will have seated the unit on the mounting brackets properly after you feel a slight movement downward and the shower panel stops moving.
- Before hanging the shower panel on the wall. Turn on both shut-off valves and test all water functions on the shower panel and check for leaks at this point. You should have good water flow to the shower panel and full temperature control from the knobs.
IMPORTANT: Abrasive cleaners should be never used on the shower panel
unite. Mild, non-abrasive cleaners should be used to clean the shower
panelunitet
If the led light does not work properly.
please clean the water impurities in the generator
The assembly and disassembly steps of the shoring panel
Disassembly steps
Assembly steps
< Mixing valve>
In order to improve the service life of the product. After the shower, turn
the ALL handwheels to OFF. Must be turning the shower faucet(Cold and hot
water mixing valve) handwheels to OFF.
< Showerhead, Body Jets, Shower wad>
Set the diverter valve to the showerhead, body jets, or shower wand setting,
the water will start. Designate the water temperature you want with the
thermostatic valve. Turn the diverter valve “off” when you are done showering.
Ira%
< How to fix the problems that you will meet whiltasing your ower panel>
There is a lack of water pressure to the sho head, shower wand, and body.
Solution. Any restriction ‘n the water suppl oses will greatly reduce the
performance of the shower panel. The firsts are to make sure shut-off vales e
f pen. Secondly. check the water supply hoses for links. Due to the limited
space of the sower panel, the hoses can get kinked very easily. Make sure the
hoses are on the wall.l.astlyMake sure your lingo sure is at GO to 80 PSI. If
it is not, you may need to speak to a professional plumber to install a
booster pump.
Leaks.
Once you find any leaks, the connection fittings and hose clamp may be loose.
Tighten them. Contact us or your dealer if the leak continues.
Care and maintenance of your shower panel
Follow these instructions to ensure your luxury shower unite lasts a long time
and to keep the warranty intact. It is very important that you follow our
proper maintenance instructions. so that your shower life will last longer.
Any damages resulted from improper care and maintenance will not be covered by
the product warranty.
The showerhead and body jets may need to be cleaned occasionally due to the
build-up of the chemistry of your water.
Remove the showerhead and body jets before cleaning. Use warm water and mild
vinegar to soak the piece before cleaning it. Or you may need to use CLR or
another hard water cleaner.
If you have any questions, please feel free to contact us.
customer service: elloalloshop@gmail.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>