WOODBRIDGE F0015BL Contemporary Single Handle Floor Mount Freestanding Tub Instruction Manual
- May 15, 2024
- WOODBRIDGE
Table of Contents
- WOODBRIDGE F0015BL Contemporary Single Handle Floor Mount Freestanding
- Specifications
- Product Usage Instructions
- DIMENSION
- TECHNICAL DATA
- PARTS & COMPONENTS
- TOOLS REQUIRED FOR INSTALLATION
- INSTALLATION INSTRUCTIONS
- FAQ
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
WOODBRIDGE F0015BL Contemporary Single Handle Floor Mount Freestanding
Tub
Specifications
- Max flow rate: 3.2 GMP at 80 PSI
- Max hand shower flow rate: 1.8 GPM AT 80 PSI
Product Usage Instructions
Preparation for Installation
Before starting the installation process, ensure to pull all dimensions of
the actual model for accurate measurements as dimensions may vary by up to 3/8
of an inch. All measurements in inches are rounded to the nearest 1/8.
DIMENSION
ATTENTION! Dimensions may vary by up to 3/8″. It is highly recommended to
pull all dimensions of the actual model for installation and measuring
purposes.
ATTENTION! Measurements in inches are rounded to the nearest 1/8″.
TECHNICAL DATA
- Max flow rate 3.2 GMP at 80 PSI
- Max hand shower flow rate 1.8 GPM AT 80 PSI
PARTS & COMPONENTS
| No | Component |
|---|---|
| 1 | Spout |
| 2 | Aerator |
| 3 | O-Ring |
| 4 | Plastic Ring |
| 5 | Body |
| 6 | Handle |
| 7 | Plastic Ring |
| 8 | Press Hat |
| 9 | Cartridge |
| 10 | O-Ring |
| 11 | Joint |
| 12 | O-Ring |
| 13 | Spray Head |
| 14 | Bracket |
| 15 | Screw |
| 16 | Flexible Hose |
| 17 | Cartridge |
| 18 | Handle |
| 19 | Screw |
| 20 | Canopy |
| 21 | Take Over |
| 22 | Cover |
| 23 | Screw |
| 24 | Triangle Plank |
| 25 | Flexible Hose |
TOOLS REQUIRED FOR INSTALLATION
INSTALLATION INSTRUCTIONS
- Put the base cover over the pipe.
- Screw the pipe to the base.
- Install the flexible hose now and ensure the flexible hoses are hand-tightened into place.(DO NOT USE SPANNER TO
- TIGHTEN AS IT CAN DAMAGE THE O-RING). The flexible hoses are to be fitted into the correct inlets for hot water and cold water. Fix the faucet body to the pipe.
- Fix the screw position
- Connect another side of the flexible hose to the water supply pipe. Make sure they are to be fitted into the correct outlets for hot water and cold water.
- Use the explosion screw to fix the base on the ground. and put the base cover over the base.
- Connect the shower hose and hand shower.
- The installation is completed.
- After installation is complete, remove the Spray head and rotate the handle to the close position. Turn the Water Supply Valves on, and check all connections for leaks. Flush the faucet by running hot and cold water in full position for one minute. Re-tighten the Aerator.
FAQ
- Q: What should I do if I encounter leaks after installation?
- A: If you experience leaks, first check all connections for tightness. If leaks persist, consider reapplying Teflon tape or silicone sealant to the connections. If issues continue, contact customer service for further assistance.
Customer Service Phone:
562-229-0088. (Monday – Friday 9 AM – 5
PM Pacic Time)
Or Email: help@woodbridgebath.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>