WOODBRIDGE F0072MBVT Fusion Single Handle Floor Mount Freestanding Installation Guide

WOODBRIDGE F0072MBVT Fusion Single Handle Floor Mount Freestanding

Specifications:

• Dimensions: 42 3/8″ x 39 3/4″ x 43 1/4″
• Materials: Brass, Stainless Steel
• Finish: Chrome
• Manufacturer: Woodbridge

Product Usage Instructions

Preparation for Installation:
Before installation, ensure all parts and components are available and accounted for as listed in the manual.

Tools Required for Installation:

• Basin Wrench
• Adjustable Wrench
• Teflon Tape
• Silicone Sealant
• Screwdriver

Installation Instructions:

1. Insert the faucet tube into the base cover.
2. Thread the tube onto the mounting tripod.
3. Hand tighten the hot and cold flexible water supply lines onto the faucet body. Do not use a wrench to tighten.
4. Insert faucet body assembly onto the faucet tube from the top and hand tighten it.
5. Secure the mounting tripod onto the floor using the attached mounting screws.
6. Locate the faucet assembly onto the rough valves from floor and secure the connection of inlet supply lines to the valves.
7. Use the explosive screw to fix the base on the floor and place the base cover over the valve.
8. Install handheld shower to the hose and check for any leaks between hose connection and handheld shower.
9. Remove the aerator from the spout (if any) and switch the diverter from handheld shower to spout mode. Let both hot and cold water flush for one minute to clear any debris from water lines.

Maintenance Tips for Special Finishes:

• DO’S: Clean with a soft cloth, Use mild soap for cleaning, Regularly check for leaks.
• DON’TS: Use abrasive cleaners, Use harsh chemicals, Apply excessive force while cleaning.

FAQ:

• Q: Can I use this faucet as a support to get in and out of the tub?
  A: No, it is not recommended to lean on, step on, or use this faucet as a support to get in and out of the tub.

Please follow safety guidelines provided in the manual.
Retain these installation instructions for future reference!
Thank you for using WOODBRIDGE products!
Contact Customer Service at 562-229-0088 (Monday – Friday 9 AM – 5 PM Pacific Time) for any questions or concerns.

PREPARATION FOR INSTALLATION

ATTENTION! Dimensions may vary by up to 3/8″. It is highly recommended to get all dimensions of actual model for installation and measuring purposes.

• Measurements in inches are rounded to the nearest 1/8″.

TECHNICAL DATA

• Max spout flow rate 4.5 GPM at 80 PSI
• Max hand shower flow rate 1.8 GPM AT 80 PSI

PARTS & COMPONENTS

TOOLS REQUIRED FOR INSTALLATION

OTHER TOOLS MAY BE REQUIRED

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS FOR FLOOR MOUNT TUB FILLER FAUCET
BEFORE BEGINNING INSTALLATION:

1. Open the package and inspect the faucet for any defect or missing parts prior to installation.
2. This faucet should be located away from traffic areas; impact both by foot traffic or floor cleaning equipment may damage the faucet and might cause a leak which result in water damage.
3. Please read this installation instruction throughhly, make sure that you have all the required tools and supplies needed to complete this installation.
4. Due to the applicationa and design of this faucet, extensive consideration should given to its installation.
5. Flush all supply lines prior to installation.
6. Shut off both HOT and COLD supply line after flushing.

Step 1: Insert the faucet tube into the base cover.
Step 2: Thread the tube onto the moun ng tripod.

Step 3: Hand tighen the hot and cold flexible water supply line onto faucet body.
DO NOT USE wrench or Spanner to tighten as it could damage the O-Ring on the supply lines. The flexible supply line are to be fitted onto correct inlets for Hot and Cold water.
Step 4: Insert faucet body assembly onto the faucet tube from the top and hand tighen it.Make sure the flexible water supply lines go through the tube smoothly.

Step 5: Secure the mounting tripod onto the floor using the attached mounting screws.
Step 6: Locate the faucet assembly onto the rough valves from floor, and secure the connection of inlet supply lines to the valves.
DO NOT reverse the Hot and Cold supply.

Step 7: Use the explosive screw to fix the base on the floor and place the base cover over the valve.
Step 8: Make sure the black gasket is in the hose end with flats, thread hose onto outlet and tighten it. Turn the supply lines on and turn the handle to full operate position, hold the hose inside the tub and let it flush for one minute.

Step 9: Install hand held shower to the hose and check for any leak between hose connection and hand held shower
Step 10: Remove the aerator from the spout (if any) and switch the diverter from hand held shower to spout mode and and let both hot and cold water flush for one minute to clear any debris from water lines. Replace aerator and faucet is ready to use.

MAINTENANCE TIPS FOR SPECIAL FINISHES.
Brushed Gold, Matte Black and Oil Rubbed Bronze finish are considered living finish and as such color change are part of the living finish behavior. Their lacquers are affected by pollutants, temperature extremes and household cleaning solutions. We want to ensure that you get a long-lasting performance faucet from Woodbridge, therefore special care and periodic waxing should be taken starting from the time the fixture’s installed.Please read the following care instructions carefully and keep this maintenance card.

DO’S

• Use only a silicone-based caulking such as poly seam seal on installation.
• Wipe the faucet dry after each use.
• Clean only with non-abrasive cleaning products, since are products are non-porous you will only need a mixture of mild non-abrasive soap and water such as dish washing.
• If desired you periodically can apply a light coating of carnauba wax, spray carwax; this will prevent the accumulation of mineral deposits on the surface of your faucet.
• Periodically remove aerator and clean any debris accumulated as this will reduce the flow of water.

DON’TS

• Do not use any abrasive cleaners or cleaners containing ammonia, bleach, acids, alcohol, solvents or other products not recommended for metallic finishes on cleaning the faucet.
• Do not let water accumulate on the fixtures surface as the mineral deposits will dull the finish.

WARNING !
DO NOT LEAN ON, STEP ON OR USE THIS FAUCET AS A SUPPORT TO GET IN AND GET OUT FROM THE TUB.

Retain these installation instructions for future reference!
Thank you for using WOODBRIDGE products!

WOODBRIDGE®
15600 Blackburn Ave, Norwalk, CA 90650 USA
Please don’t hesitate to contact us if you have any questions or concerns.
Customer Service Phone: 562-229-0088. (Monday – Friday 9 AM – 5 PM Pacific Time) Or Email: help@woodbridgebath.com
www.woodbridgebath.com

References

• ᐅ【One Piece Toilets | Freestanding Bathtubs | Shower Bases | WOODBRIDGE】

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>