DOSS Extreme Boom Pro Portable Outdoor Speaker User Guide

July 13, 2024
Doss

DOSS Extreme Boom Pro Portable Outdoor Speaker

DOSS Extreme Boom Pro Portable Outdoor Speaker

Packing Content

  • 1 x Extreme Boom Pro
  • 1 x USB-C charging cable
  • 1 x Strap
  • 1 x User Manual

Specifications

Output power : 40W2+10W2
DC power input : 5V 3A
USB output : 5V 2A
Battery : 10400mAh
Charge time : 4.5hrs
Playtime: 20hrs (at 50% volume-Hotel California)
Bluetooth range : up to 30m/99ft
Net weight : 7.2lbs/3.24kg
Unit dimension : 14.256.378.07 inches TF card audio format: MP3/ WAV/ FLAC/APE (Max capacity 256G)

Important Notes Before Using

  • To prolong the lifetime of the battery, fully charge the speaker before the first time using it.
  • The battery is at a low level when the 25% LED indicator blinks.
  • The speaker will auto-power off after 15 minutes without audio input.
  • To cancel the auto-power off feature, press M for 3s simultaneously.
  • The USB out is only for charging your device.
  • Restore the factory setting by pressing and holding ► the for 3s simultaneously.
  • Press any button to check the battery level while not charging.
  • When all buttons can‘t be controlled, try to reset the speaker with a paper clip (the reset button on the back of the speaker).
  • If you need any assistance while using this speaker, please feel free to contact customer service at support@dossav.com.

Buttons And Control

Buttons And Control

| Press and hold 3s| Turn on/off
---|---|---
Press| Enter Bluetooth pairing

| Press and hold 3s| Next track
Press| Volume up

─-

| Press and hold 3s| Previous track
Press| Volume down

| Press and hold 3s| Disconnect Bluetooth
Press| Play/pause
Press| Reconnect with last device
| Press and hold 3s| Fixed light color
Press| Change 5 light show effects
| Press and hold 3s| Enter/Exit Part sync pairing
Press| Enter/Exit TWS pairing

M

| Press and hold 3s| Extra bass on/off
Press| Change play modes

| Press and hold 3s| Check version ID (Only Works while Bluetooth disconnecting)
| Press and hold 3s| Restore factory setting

M

| Press and hold 3s| Cancel/activate the auto-power off feature ( Only works at Bluetooth mode)

LED indications

M Flashing blue Bluetooth pairing
Solid blue Bluetooth paired
Solid red AUX mode
Solid green TF card mode
Red blinks once Extra bass on
Green blinks once Extra bass off
Flashing white Enter TWS pairing
Solid white Enter Partysync pairing
4 white LEDs Battery level 100%
3 white LEDs Battery level 75%
2 white LEDs Battery level 50%
1 white LED Battery level 25%

Connections

Connections
Connections
Connections
Connections
Connections

Bluetooth Mode

  1. Enable the Bluetooth feature on your device.
  2. Find “Extreme Boom Pro” on the Bluetooth device and connect it.
  3. Once paired, you can see the status “connected” on your device.
  • Press to re-enter Bluetooth pairing if your device can’t find Extreme Boom Pro in 10 seconds.
  • This speaker can pair with 2 devices via Bluetooth simultaneously, but it can only play music on one device at a time. To play from the other connected device, pause the currently playing one first.

Tws (True Wireless Stereo) Mode

  1. Press the on both Extreme Boom Pro to enter into TWS pairing.
    Once paired, the LED of the primary speaker turns solid white, while the second speaker turns to flash white.

  2. Find “Extreme Boom Pro” on your Bluetooth device and connect it.

  • If 2 smart devices are connected, and you want to play via TWS mode, press to enter into TWS pairing, meanwhile, the current playing device will be disconnected.
  • In TWS mode, if you want to play via PartySync mode, press to exit TWS mode first.

Partysync Mode

  1. Turn on one speaker and get it paired with your device. Then press and hold for 3s to enter the PartySync mode. The speaker will be the primary speaker and the LED comes solid white.
  2. Turn on the other speaker(s) and long press to enter the PartySync mode. The speaker(s) will be the secondary speaker(s) and the LED comes off.
  • If 2 smart devices are connected, and you want to play via PartySync mode, press and hold to enter into PartySync pairing, meanwhile, the currently playing device will be disconnected.
  • In PartySync mode, if you want to play via TWS, press and hold to exit PartySync mode first.
  • The M► ─- on secondary speaker can’t be controlled under PartySync mode.

Use your speaker with Echo Dot

You can connect the Dot with the speaker by Bluetooth.

Please follow the steps to set up via Bluetooth:

  1. Download the Alexa app and follow the steps to set up the procedure to get the Dot connected to your home Wi-Fi network.
  2. Switch the Extreme Boom Pro to Bluetooth mode, you can press the power button to re-enter Bluetooth pairing.
  3. Run the Alexa app, tap Menu, and then tap Settings.
  4. Tap the Echo Dot in your list of Alexa devices, then tap Bluetooth.
  5. The Extreme Boom Pro should appear in the list of Bluetooth devices. If not, please press the power button and try again.
  6. Once listed, tap on the speaker to complete the pairing process.
  7. To remove the device, return to Bluetooth>tap the name of the speaker> tap “Forget Device”

Note:

Voice command will not be able to turn on/off the speaker if you connect to it via Bluetooth.

Safety Instructions

Avoid dropping or hiting the speaker.
Avoid exposing to extreme temperature.
Avoid using the speaker near a microwave.
Never disassemble or repair the speaker.
Never use any corrosive cleanser/oil to clean.
Never leave the speaker in a car parked in the sun.
Never attempt to charge the speaker while it is wet.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment should be installed and operated with a minumum distance of 20 cm between the radiator and your body.

Customer Service

@dossav / @dossfans @dossdirect
www.dossaudio.com
1-833-275-3677 Mon-Fri 9AM-SPM PT (USA)

US: support@dossav.com
UK: support_uk@dossav.com

EVATOST CONSULTING LTD

 Office 101 32 Threadneedle Street, London, United Kingdom, EC2R 8AY contact@evatost.com
OST_UK _20220119000010
We simply act as UK representative for cross-border sellers, and are not manufacturers/importers/distributors for the product, nor involved in the manufacture/import/sale of the product. Therefore, we are not responsible for any after-sales services related to the product. In case of any product quality or infringement issues, the manufacturer/importer/seller shall be solely held responsible.
 eVatmaster Consulting GmbH
Bettinastr. 30
60325 Frankfurt am Main,Germany
contact@evatmaster.com
OST EU 20220119000015
We simply act as EU representative for cross-border sellers, and are not manufacturers/importers/distributors for the product, nor involved in the manufacture/import/sale of the product. Therefore, we are not responsible for any after-sales services related to the product.
In case of any product quality or infringement issues, the manufacturer/importer/seller shall be solely held responsible.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals