Bluetooth Speaker, DOSS SoundBox Pro Portable Wireless Speaker with 20W Stereo Sound-Complete Features/User Guide

Bluetooth Speaker, DOSS SoundBox Pro Portable Wireless Speaker with 20W

Stereo Sound ****

Specifications

• PRODUCT TYPE: Wireless Portable Bluetooth Speaker with Built-in Microphone
  OUTPUT POWER: 6W x 2

• DRIVER UNIT: 1.5 inch speaker x 2 + 2.6 inch passive radiator

• FREQUENCY RESPONSE: 100Hz-18kHz

• UNIT WEIGHT: 560 g

• UNIT DIMENSION: 6.6 x 2.7 x 2.9 inch
  WARRANTY: One-year limited

• POWER: INPUT: 5V, 1A

• WIRELESS/NETWORKING

• BLUETOOTH VERSIONS: Profiles supported

Introduction

At any level, two full-range drivers and dual passive radiators deliver 20W stereo sound with improved bass, tight mids, and crystal clear highs. Simply press the button to increase the bass and volume. Enjoy the bass permeating every nook and cranny of your space. Connect two SoundBox Pro speakers to one device for 360° stereo sound and double the volume. 6 color and 3 illumination patterns were added in the amazing light that react and phase in time with the beat.

Allow the DOSS Soundbox Pro waterproof Bluetooth speaker to join in the fun by the pool or at the beach, even if it’s raining. The speaker is waterproof to IPX5 standards, which means it can withstand water splashes, spray, and rain. However, do not immerse it in water.

PACKAGE CONTENT

• One wireless portable speaker
• USB charging cable
• Φ3.5mm auxiliary cable
• Travel waterproof pouch
• User manual, Warranty card, a Contact card

PRODUCT OVERVIEW

BACKLIT TOUCH-SENSITIVE BUTTONS

1. Mode switch: Touch MODE to toggle play mode among Bluetooth,
2. In Bluetooth mode/TF mode, touch the rewind button to skip backward.
3. play/pause and handset button

• In Bluetooth mode, touch to answer or end a call. Touch for 3 seconds to reject a call.
• In Bluetooth mode, touch  to play/pause your tune. Touch for 3 seconds to disconnect with your device.
• In TF mode, touch to play/pause your tune.

4. In Bluetooth mode/TF mode, touch the forward button to skip forward.
5. Volume control:

• Clockwise rotation to increase the volume
• Counterclockwise rotation to decrease the volume

6. power button: long press to turn the device on and off.
7. Auxiliary Φ3.5mm jack: use it for cabled playback with compatible devices
8. TF card: Use it for TF card (with music) playback. support mp3, wav, to FAT32.
9. Charging port: Plug the supplied USB cable into this port to recharge the built-in battery.
10. LED charging indicator.

• Charging: Steady Red.
• Fully charged: Steady Green.

STATUS INDICATORS

enter indicator/

|

Flashing blue

| Indicates that the speaker has entered into the pairing mode and it is ready to be paired
---|---|---

Steady blue

| Indicates that the device is successfully paired

Steady red

| This indicates that the device has switched to the auxiliary input mode

Steady Green

| This indicates that the device has switched to the TF mode

indicator

| Steady red|
Steady green|

PREPARATION

Use the supplied USB cable to charge your portable speaker directly from your computer or device with a micro USB port.

• Make sure that the speaker is fully charged before using it for the first time
• Remember to note the above point and fully charge your speaker prior to the first use. It will take approximately 2-3 hours to recharge after.
• The LED light will remain RED when charging and turn GREEN once the charge completes.

Press & hold the power button to turn on the speaker. Repeat the steps to turn the device off as well.

NOTE
 The speaker has a built-in battery saver mode where it will automatically power off if not in use for 15 minutes. This function can be removed with a firmware upgrade. For assistance, please contact: [email protected]

PAIRING THE WIRELESS SPEAKER WITH YOUR SMART DEVICE

1. Place your smart device and wireless speaker no more than one meter away from each other.
2. Press the power button located on the back of the speaker for several seconds to turn it on.
3. Set your smart device to “discover” the wireless speaker. Upon powering on, a tone will be heard, the blue LED will start flashing, accompanied by a prompt notifying that the speaker has entered into the pairing mode.
4. Enabled Bluetooth on your device and choose DOSS SoundBox from the list.
5. If pairing is successful, the LED will change to steady blue and your phone will confirm that the connection has been established. If the pairing process fails after 60 seconds, please repeat steps 1 through 5 described above.
6. long-press the button you can disconnect the Bluetooth.

NOTE
If your smart device cannot discover the SoundBox, long-press the button and have a try again.

ANSWERING AND ENDING A CALL USING YOUR SPEAKER OR MOBILE PHONE

1. When there is an incoming call, the speaker will generate a tone and a verbal notification to alert you of this event.
2. Briefly press the handset button to pick up, and long press to reject.
3. Speak with a clear voice right into the built-in microphone located on the front section of the speaker
4. To end a call, tap the handset button once again. Likewise, you may also end the call directly using the command on your cell phone.
5. When listening to music using your smartphone, playback will resume

USING IT WITH YOUR ECHO DOT

You can connect the Dot with the speaker using a 3.5 mm auxin cable or Bluetooth. Please use the following steps to set up using Bluetooth:

1. Download the Alexa APP, and follow the standard setup procedure to get the dot connected to your home Wi-Fi network.
2. Switch the SoundBox speaker to Bluetooth mode, you can press the ‘play/handsfree’ button for 5 seconds to keep it in pairing status.
3. Run the Alexa app, tap Menu, and then tap Settings.
4. Tap the Echo Dot in your list of Alexa Devices, then tap Bluetooth.
5. The SoundBox speaker should appear in the list of Bluetooth Devices. If not, press the “play/hands-free” button for 5 seconds and try again. Once listed, tap on The SoundBox speaker to complete the pairing process. To remove the device, return to Bluetooth -> tap the name of the speaker -> then tap “Forget Device”.

NOTE

1. Voice command will not be able to turn on/off the Soundbox no matter whether you connect it via Bluetooth / Aux cable. It can only translate sound signal.
2. To remove the battery saver option, please contact our customer service at [email protected] to remove the function by upgrading the firmware.

 | Problem|
---|---|---
Bluetooth| Cannot Pair with Bluetooth devices|

seconds, then have a try to pair it again

 | Please select ‘DOSS SoundBox’ as the default playback device
The song cuts off during

playback

|

Please check if the Bluetooth distance is more than 33 feet or

There is noise during playback| May be caused by the interference of charging, try to put it in another place and do not charge it during playback
Laptop prompts to install the driver| This driver is not special for Soundbox, it’s for your laptop

contact the computer company or windows

 | for 5 seconds or contact the for help
TF Card| The speaker does not play when the card is inserted, and jumps directly back to Bluetooth mode| Check whether the card format is FAT or FAT32. If not, format it to FAT or FAT32.

Check the song format. The speaker only supports MP3, WAV

The song cuts off during

playback

| There may be a problem with the

the same file

other| All the lights are lit and can not

be turned off

| Use the needle or wire to poke the

Customer Service Email| [email protected]

WARNING

• Do NOT drop, hit or shake the device.
• Do NOT disassemble, repair or modify the Bluetooth speaker by yourself.
• Do NOT use cleaning products that contain benzene, solvents or alcohol.
• Do NOT expose the Bluetooth speaker to excessive heat or to direct sunlight for long periods of time.
• Do NOT store the device in a place with high humidity or dust.
• Do NOT place heavy objects on top of the Bluetooth speaker.
• Do NOT use near a microwave oven or wireless LAN products.

Frequently Asked Questions

• What is the best way to tell if my DOSS SoundBox is charged?
  To turn on the speaker, press and hold the power button. To turn the gadget off, repeat the instructions. When charging, the LED light will remain RED and will turn GREEN after the charge is complete.

• How do you activate pairing mode on SoundBox pro?
  To reconnect the SoundBox Pros’ stars pairing, turn on both speakers and press and hold the ADD button on either of them. The coupling will happen on its own. When one or both speakers are switched off without disconnecting from the stereo pairing mode, the speakers will immediately rejoin when powered on.

• What are the many modes available on a DOSS speaker?
  Touch to answer or end a call in Bluetooth mode. To reject a call, press and hold for three seconds.
  Touch to play/pause your music in Bluetooth mode. To disconnect from your device, press and hold for three seconds.
  Touch to play/pause your tune in TF mode.

• What is the procedure for turning off the lights on my DOSS SoundBox pro?
   To turn off the light, long-press the “EXTRA BASS” button three times.

• How can I upgrade the firmware on my DOSS SoundBox?
  Please power on the speaker and place the micro SD card in the TF card slot on the speaker’s rear. The metal connections of the micro SD card should be facing up. The firmware of the speaker should be updated automatically, and the device should switch off once the update is completed.

• What is the procedure for resetting DOSS SoundBox pro?
  To reset the device, press and hold the play/pause button until an audible noise is heard.

• How long does it take to charge a DOSS speaker?
  The speaker’s output is 12V DC at 2.5A and charges in around 2-3 hours, but DOSS suggests charging it for at least 12 hours the first time. The speaker will begin to charge as soon as you plug it in, and the battery indicator LED will turn a steady red.

• What’s the deal with my Doss SoundBox beeping?
  This occurs as a result of a low battery alert, a device connection, or when charging is complete. The frequency, tone, and intensity of the beeping sounds will change based on the status of your Bluetooth speaker.

• Why is it that my Doss SoundBox keeps shutting down?
  Volume levels and usage habits may be to blame for your problems. Using the DOSS SoundBox’s full power for long periods of time may cause the 12-hour average duration time to change. Before disconnecting your device from the charger, you might wish to check the battery level.

• How can I connect my SoundBox plus to my computer?
  To turn on the speaker, press and hold the power button on the rear for several seconds. 3. Tell your smartphone or tablet to “find” the Bluetooth speaker. A tone will be heard when the speaker is turned on, and the blue LED will begin blinking, followed by a notification indicating that the speaker has entered pairing mode.

https://www.manualslib.com/download/1318215/Doss-Soundbox.html

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>