HIKOKI SB 3608DA 36V Brushless 76mm Belt Sander Bare Tool Instruction Manual

HIKOKI SB 3608DA 36V Brushless 76mm Belt Sander Bare Tool Instruction Manual

 Handling instructions

GENERAL POWER TOOL SAFETY WARNINGS

WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided with this power tool.

Failure to follow all instructions listed below may result in electric shock, fi re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of fl ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.

Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodifi ed plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.

Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the infl uence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off -position before connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your fi nger on the switch or energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-related hazards.

h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles.
A careless action can cause severe injury within a fraction of a second.

Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off .
Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/ or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.

e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may aff ect the power toolʼs operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
Use of the power tool for operations diff erent from those intended could result in a hazardous situation.

h) Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

a) Recharge only with the charger specifi ed by the manufacturer.
A charger that is suitable for one type of battery pack may create a risk of fi re when used with another battery pack.

b) Use power tools only with specifi cally designated battery packs.
Use of any other battery packs may create a risk of injury and fi re.

c) When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another.
Shorting the battery terminals together may cause burns or a fi re.

d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, fl ush with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns. 

e) Do not use a battery pack or tool that is damaged or modifi ed.
Damaged or modifi ed batteries may exhibit unpredictable behaviour resulting in fi re, explosion or risk of injury.

f) Do not expose a battery pack or tool to fi re or excessive temperature.
Exposure to fi re or temperature above 130°C may cause explosion.

g) Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specifi ed in the instructions.
Charging improperly or at temperatures outside the specifi ed range may damage the battery and increase the risk of fi re.

Service

a) Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.

b) Never service damaged battery packs.
Service of battery packs should only be performed by the manufacturer or authorized service providers.

PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of children and infi rm persons.

CORDLESS BELT SANDER SAFETY WARNINGS

Hold the power tool by insulated gripping surfaces, because the sanding surface may contact hidden wiring. Cutting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

ADDITIONAL SAFETY WARNINGS

1. Use clamps or another practical way to secure and support the workpiece to a stable platform.
   Holding the workpiece by hand or against your body leaves it unstable and may lead to loss of control.

2. Attaching and removing the dust bag Prior to the sanding operation, make sure the material of surface you are going to sand.
   If the surface under sanding operation is expected to generate harmful / toxic dusts such as lead painted surface, make sure the dust bag or appropriate dust extraction system is connected with dust outlet tightly.
   Wear the dust mask additionally, if available.
   Do not inhale or touch the harmful / toxic dusts generated in sanding operation, the dust can endanger the health of yourself and bystanders.

3. Never apply water or grinding fl uid when sanding. This could result in electrical shock.

4. Never turn the power switch ON when the sander is contacting the surface to be sanded. This is necessary to preclude damage to the material. The same applies when switching the power OFF.

5. DO NOT apply excessive pressure to the sander while sanding. Excessive-pressure may cause overload of the motor, reduced service life of the sanding belt, and lowered sanding or polishing effi ciency.

6. Never touch moving parts.
   Never place your hands, fi ngers or other body parts near the tool’s moving parts.

7. NEVER leave tool running unattended. Turn power off .
   Don’t leave tool until it comes to a complete stop.

8. When operating the tool, do not wear work gloves as such cloth wear can get caught in the tool.

9. Do not leave the tool running. Operate the tool only when hand-held.

10. Make sure that there are no cracks, scratches, or other abnormalities on the sanding belt before use.

11. Accessories must be securely mounted to the tool.
    Prevent potential injuries to yourself or others. Accessories which have been mounted to the tool should be secure and tight.

12. Use the sanding belt and accessories specifi ed by HiKOKI.

13. When sanding metal, sparks are generated. Keep other persons and fl ammable substances away from the work area.

14. Sanding belt installed in the wrong direction will lower work effi ciency and shorten life of sanding belt.

15. If sanding belt moves during operation, adjustment can be made while in operation.

16. Sanding by applying impact and cutting by side of belt contact should be avoided.

17. Be careful of sanding sparks.

18. As certain that the sanding workpiece contains neither nails nor other harmful foreign matter.

19. Sanding glass fi ber not recommended.

20. After operation, blow away the dust on the belt and the pulleys.

21. Place the workpiece on a stable surface when sanding.

22. Do not sand a steel plate for extended periods while applying excessive pressure.
    There is a risk that hot sanding particles could damage the dust bag.

23. If you notice that the unit is generating unusually high temperatures, operating poorly, or making abnormal noises, immediately stop using and shut off the power switch. Request an inspection and repair from the dealer where you purchased the unit or a HiKOKI Authorized Service Center.
    Continuing to use while operating abnormally might cause injuries.

24. If the unit is mistakenly dropped or strikes another object, make a thorough check of the unit for cracks, breakage or deformation, etc.
    Injuries might occur if the unit has cracks, breakage or deformation.

25. When working at elevated locations, clear the area of other people and aware of conditions below you.

26. Always charge the battery at a temperature of 0°C–40°C.
    A temperature of less than 0°C will result in over charging which is dangerous. The battery cannot be charged at a temperature higher than 40°C.
    The most suitable temperature for charging is that of 20°C–25°C.

27. Do not use the charger continuously. When one charging is completed, leave the charger for about 15 minutes before the next charging of battery.

28. Do not allow foreign matter to enter the hole for connecting the rechargeable battery.

29. Never disassemble the rechargeable battery and charger.

30. Never short-circuit the rechargeable battery. Shortcircuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery.

31. Do not dispose of the battery in fi re. If the battery is burnt, it may explode.

32. Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery.

33. Do not insert object into the air ventilation slots of the charger. Inserting metal objects or infl ammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger.

34. When using this unit continuously, the unit may overheat, leading to damage in the motor and switch. Therefore, whenever the housing becomes hot, give the tool a break for a while.

35. Make sure that the battery is installed fi rmly. If it is at all loose it could come off and cause an accident.

36. Do not use the product if the tool or the battery terminals (battery mount) are deformed.
    Installing the battery could cause a short circuit that could result in smoke emission or ignition.

37. Keep the tool’s terminals (battery mount) free of swarf and dust.

    • Prior to use, make sure that swarf and dust have not collected in the area of the terminals.
    • During use, try to avoid swarf or dust on the tool from falling on the battery.
    • When suspending operation or after use, do not leave the tool in an area where it may be exposed to falling swarf or dust.
      Doing so could cause a short circuit that could result in smoke emission or ignition.

38. Always use the tool and battery at temperatures between -5°C and 40°C.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the protection function to stop the output.
In the cases of 1 to 3 described below, when using this product, even if you are pulling the switch, the motor may stop. This is not the trouble but the result of protection function

1. When the battery power remaining runs out, the motor stops.
   In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this case, release the switch of tool and eliminate causes of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the battery power may stop.
   In this case, stop using the battery and let the battery cool. After that, you can use it again.
   Furthermore, please heed the following warning and caution

WARNING
In order to prevent any battery leakage, heat generation, smoke emission, explosion and ignition beforehand, please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the battery. ‘
   • During work make sure that swarf and dust do not fall on the battery.
   • Make sure that any swarf and dust falling on the power tool during work do not collect on the battery.
   • Do not store an unused battery in a location exposed to swarf and dust.
   • Before storing a battery, remove any swarf and dust that may adhere to it and do not store it together with metal parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such as a nail, strike with a hammer, step on, throw or subject the battery to severe physical shock.
3. Do not use an apparently damaged or deformed battery.
4. Do not use the battery for a purpose other than those specifi ed.
5. If the battery charging fails to complete even when a specifi ed recharging time has elapsed, immediately stop further recharging.
6. Do not put or subject the battery to high temperatures or high pressure such as into a microwave oven, dryer, or high pressure container.
7. Keep away from fi re immediately when leakage or foul odor are detected.
8. Do not use in a location where strong static electricity generates.
9. If there is battery leakage, foul odor, heat generated, discolored or deformed, or in any way appears abnormal during use, recharging or storage, immediately remove it from the equipment or battery charger, and stop use.
10. Do not immerse the battery or allow any fl uids to fl ow inside. Conductive liquid ingress, such as water, can cause damage resulting in fi re or explosion. Store your battery in a cool, dry place, away from combustible and fl ammable items. Corrosive gas atmospheres must be avoided

CAUTION

1. If liquid leaking from the battery gets into your eyes, do not rub your eyes and wash them well with fresh clean water such as tap water and contact a doctor immediately.
   If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with clean water such as tap water immediately.
   There is a possibility that this can cause skin irritation.

3. If you fi nd rust, foul odor, overheating, discolor, deformation, and/or other irregularities when using the battery for the fi rst time, do not use and return it to your supplier or vendor

WARNING
If a conductive foreign matter enters in the terminal of lithium ion battery, the battery may be shorted, causing fi re. When storing the lithium ion battery, obey surely the rules of following contents

• Do not place conductive debris, nail and wires such as iron wire and copper wire in the storage case.
• To prevent shorting from occurring, load the battery in the tool or insert securely the battery cover for storing until the ventilator is not seen.

REGARDING LITHIUM-ION BATTERY TRANSPORTATION

When transporting a lithium-ion battery, please observe the following precautions.

WARNING
Notify the transporting company that a package contains a lithium-ion battery, inform the company of its power output and follow the instructions of the transportation company when arranging transport.

• Lithium-ion batteries that exceed a power output of 100 Wh are considered to be in the freight classifi cation of Dangerous Goods and will require special application procedures.
• For transportation abroad, you must comply with international law and the rules and regulations of the destination country
  

USB DEVICE CONNECTION PRECAUTIONS

When an unexpected problem occurs, the data in a USB device connected to this product may be corrupted or lost.
Always make sure to back up any data contained in the USB device prior to use with this product.

Please be aware that our company accepts absolutely no responsibility for any data stored in a USB device that is corrupted or lost, nor for any damage that may occur to a connected device.

WARNING

• Prior to use, check the connecting USB cable for any defect or damage.
  Using a defective or damaged USB cable can cause smoke emission or ignition.

• When the product is not being used, cover the USB port with the rubber cover.
  Buildup of dust etc. in the USB port can cause smoke emission or ignition.

NOTE

• There may be an occasional pause during USB recharging.

• When a USB device is not being charged, remove the USB device from the charger.
  Failure to do so may not only reduce the battery life of a USB device, but may also result in unexpected accidents.

• It may not be possible to charge some USB devices, depending on the type of device.

NAMES OF PARTS (Fig. 1–Fig. 18)

1. Handle knob
2. Housing
3. Sanding belt
4. Guard
5. Adjust screw
6. Belt cover
7. Slide fastener
8. Dust bag
9. Duct
10. Trigger switch
11. Lock on button
12. Elbow
13. Dial
14. Nameplate
15. Handle
16. Battery
17. Drive pulley
18. Drive pulley rotation direction arrow (marking)
19. Lever
20. Idle pulley
21. Ventilation holes
22. Motor
23. Latch
24. Charge indicator lamp
25. Arrows on the inside of the belt
26. Side of housing
27. Dust collector
28. Battery level indicator switch
29. Battery level indicator lamp’
30. Air blow gun
31. Terminal (Battery)
32. Sliding grooves
33. Terminal (Product)
34. Battery sliding grooves

SYMBOLS

WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before use.

SB3608DA : Cordless Belt Sander
To reduce the risk of injury, user must read instruction manual.
Only for EU countries
Do not dispose of electric tools together with household waste material!
In observance of European Directive 2012/19/EU on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
Direct current
Rated voltage
No-load speed

Disconnect the battery
Switching ON
Switching OFF
Switch locks to the “ON” position
Lock
Unlock
Warning

Battery

Lights ;
The battery remaining power is over 75%
Lights ;
The battery remaining power is 50%–75%.
Lights ;
The battery remaining power is 25%–50%.
Lights ;
The battery remaining power is less than 25%
Blinks ;
The battery remaining power is nearly empty.
Recharge the battery soonest possible.
Blinks ;
Output suspended due to high temperature.
Remove the battery from the tool and allow it to fully cool down.
Blinks ;
Output suspended due to failure or malfunction.
The problem may be the battery so please contact your dealer.

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the accessories listed on page 217.

Standard accessories are subject to change without notice.

APPLICATIONS

• Finish sanding and fi nish fl ooring of woodwork products.
• Base polishing of wood-coated surfaces.
• Finish sanding of metal surfaces.
• Base polishing of metal-coated surfaces, rust removal, or paint removal prior to refi nishing.
• Surface fi nishing of slate, concrete, and similar materials.

SPECIFICATIONS

Power tool

4.5 kg (BSL36B18)

Existing batteries (BSL3660/3620/3626, BSL18xx series, etc.) cannot be used with this tool.
** According to EPTA-Procedure 01/2014 Also, the weight includes the dust bag

• Existing batteries (BSL3660/3620/3626, BSL18xx series, etc.) cannot be used with this tool.
  ** According to EPTA-Procedure 01/2014 Also, the weight includes the dust bag.

NOTE
Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to change without prior notice.

Electronic control

• Braking Function
  Brake is activated when the switch is turned off , stopping the motor’s rotation.
  Soft start

• Variable speed

• Constant speed

• Overload protection
  This protection feature cuts off the power to the motor in the event of overloading of motor or a conspicuous reduction in rotational speed during operation.
  When the overload protection feature has been activated, the motor may stop.
  In this case, release the tool switch and eliminate causes of overloading.
  After that you can use it again.

• Overheat protection
  This protection feature cuts off the power to the motor and stops the power tool in the event of overheating of motor during operation.
  When the overheat protection feature has been activated, the motor may stop.
  In this case, release the tool switch and cool it down in a few minutes.
  After that you can use it again.

• Restart prevention function
  When the power is still switched on, the tool will not restart when a battery is installed. This function can be canceled once the tool is switched off .

Battery

• The tool itself will automatically switch over.

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect the charger’s power cord to the receptacle.
   When connecting the plug of the charger to a receptacle, the charge indicator lamp will blink in red (At 1- second intervals).

2. Insert the battery into the charger.
   Firmly insert the battery into the charger as shown in Fig. 3.

3. Charging
   When inserting a battery in the charger, the charge indicator lamp will blink in blue. When the battery becomes fully recharged, the charge indicator lamp will light up in green. (See Table 1)

4. Charge indicator lamp indication The indications of the charge indicator lamp will be as shown in Table 1 , according to the condition of the charger or the rechargeable battery
   Charger
   status| Status of indicator
   lamp| Indication meaning
   ---|---|---
   Before charging| ONOFF at 0.5 sec.intervals (RED)
   | Plugged into power source ‘t
   While
   charging| Lights for 0.5 sec. at intervals of 1 sec. (BLU          | Charged at less than 50%
   Lights for 1 sec. at intervals of 0.5 sec. (BLUE)| Charged al less than 80%
   Lights continuously (BLUE)| Charged at more than 80%
   Charging
   complete| Lights continuously (GREEN)
   |
   (Continuous buzzer sound: about 6 sec.)
   Overheat standby| ON/OFF at 0.3 sec. intervals (RED
   | Battery overheated. Unable to charge. ‘2
   Charging
   impossible| ON/OFF at 0.1 sec.intervals (PURPLE

(Intermittent buzzer sound; about 2 sec.)| Malfunction inthe Denary or the charger .3

• Fully insert the battery.

• Check to confi rm that no foreign matter is stuck to the battery mount or terminals.
  If charging takes a long time

• Charging will take longer at extremely low ambient temperatures. Charge the battery in a warm location (such as indoors).

• Do not block the air vent. Otherwise the interior will overheat, reducing the charger’s performance.

• If the cooling fan is not operating, contact a HiKOKI Authorized Service Center for repairs.

2. Regarding the temperatures and charging time of the rechargeable battery The temperatures and charging time will become as shown in ****Table 2.  

(BSI-1430C.
B.S11830C: 30 min)
4.0 Ah| 26 min
(BSI-1840M: 40 min)
5.0 Al.| 32 min
6.0 Ah| 38 min
8.0 Ah| 52 min
Multivisa battery| 1.5 Ah (ic 2 unit)| 20 min
2.5 Ah (x 2 unit)| 32 min
4.0 Ah (x 2 unit)| 52 min
Number of battery cells| 4-10
Charging voltage fo USB| 5 V
Charging current for USB| 2 A
Weight| 0.6 kg

1. If the red lamp continues to blink even after the charger has been attached, check to confi rm that the battery has been fully inserted.
2. Although charging will start once the battery has cooled down even when left in situ, the best practice is to remove the battery and allow it to cool down in a shaded, well-ventilated location before charging.

NOTE
The recharging time may vary according to the ambient temperature and power source voltage.

CAUTION
When the battery charger has been continuously used, the battery charger will be heated, thus constituting the cause of the failures. Once the charging has been completed, give 15 minutes rest until the next charging.

1. Disconnect the charger’s power cord from the receptacle.
2. Hold the charger fi rmly and pull out the battery.

NOTE
Be sure to pull out the battery from the charger after use, and then keep it.

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the fi rst and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2–3 times.

How to make the batteries perform longer.

1. Recharge the batteries before they become completely exhausted.
   When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter.

2. Avoid recharging at high temperatures.
   A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while.

CAUTION

• If the battery is charged while it is heated because it has been left for a long time in a location subject to direct sunlight or because the battery has just been used, the charge indicator lamp of the charger lights for 0.3 seconds, does not light for 0.3 seconds (off for 0.3 seconds). In such a case, fi rst let the battery cool, then start charging.
• When the charge indicator lamp fl ickers (at 0.2-second intervals), check for and take out any foreign objects in the charger’s battery connector. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your authorized Service Center.

MOUNTING AND OPERATION

1. Removing and inserting the battery
   CAUTION
   Before installing or removing the battery, turn the switch
   to the OFF position.
   If the battery is inserted with the switch in the ON
   position, the motor will operate unexpectedly.

2. Installing the sanding belt
   Align the arrow on the inside of the sanding belt with the direction of the mark on the tool and install it.
   CAUTION
   ○ Use only sanding belt size specifi ed on the product nameplate.
   ○ Sanding belt installed in the wrong direction will lower work effi ciency and shorten life of sanding belt.
   ○ Avoid pinching your fi ngers when opening and closing the lever.
   NOTE
   ○ The drive pulley and idle pulley will be hot after use.
   ○ Use an air blow gun or similar device to remove any debris from around the pulleys with the sanding belt removed.

3. How to use the dust bag
   WARNING
   Clean the dust bag before and after sanding metal, and remove any sanding. dust from inside. Metal sanding dust can cause fires.

4. How to use the elbow
   Adjust the angle of the elbow so that the dust is
   discharged away from your body.

5. About the mode change function
   The unit has “Transmission mode” and “Auto mode”.

   • With Transmission mode, the belt sander’s number of revolutions can be set at one of fi ve stages. When operating in Transmission mode, the set number of revolutions will be maintained regardless of changes in load.
   • With Auto mode, you can lower noise and vibration by lowering the maximum number of revolutions while in a no-load state. While in Auto mode, the number of revolutions will be raised if the load becomes greater during operation. On the other hand, the number of revolutions will be lowered if the load decreases during operation. (Table 3)
   • Set the mode and dial according to work application.
     Dial setting| Belt speed
     ---|---
     1| 122 m/min
     2| 220 m/min
     3| 310 m/min
     4| 400 m/min
     5| 450 m/min
     A| 122 m/min (No load)
     450 m/min (With load)

6. How to adjust sanding belt position
   WARNING

   • If the sanding belt is positioned too close to the inside, it may come into contact with the guard, producing sparks.

   • Do not peer inside between the sanding belt and housing. Doing so risks dust or other debris entering your eyes.
     NOTE

   • If sanding belt moves during operation, adjustment can be made while in operation.

   • Setting the dial to low speed (e.g., mode 1) makes it easier to adjust.

   • If the sanding belt is positioned too close to the inside, it may come into contact with the guard, causing the belt to tear

7. How to hold and move the belt sander

   • Remove the tool from the workpiece and turn on the trigger switch. When fi nishing, turn off the trigger switch after the tool is removed from the workpiece, and set the tool down after the rotation has stopped.
   • Grasp handle and handle knob and hold machine against surface to be worked on so that it contacts surface lightly.
   • Hold both handles fi rmly, and take great care to keep your fi ngers away from the pulleys and sanding belt while working.
   • Weight of machine itself is suffi cient for sanding and polishing at highest effi ciency.
   • Do not apply any additional pressure, for this would place unnecessary load on motor, shorten life of sanding belt and lower work effi ciency.
   • Choose sanding belt of proper grain size and grain type for your specifi c purpose, by referring to Table 4 and 5 below.

MAINTENANCE AND INSPECTION

WARNING
Be sure to turned off the switch and remove the battery before maintenance and inspection.

1. Empting and cleaning the Dust Bag
   Clean the dust bag after working to remove any sanding dust. (Fig. 5)
   NOTE
   If too much dust accumulates in the dust bag, the dust collection power will be reduced. Dispose of dust as soon as possible.
   

2. Inspecting the sanding beIt
   The abrasive performance of the sanding belt will decrease if its abrasive particles become worn away or clogged, greatly reducing the effi ciency of the tool. If this occurs, replace with a new sanding belt.

3. Cleaning on the outside
   When the power tool is stained, wipe with a soft dry cloth or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics.

4. Cleaning the battery installation compartment and the battery
   WARNING
   Wear protective glasses and a dust mask when cleaning with an air blow gun.
   Failure to do so may result in inhalation or exposure of the eyes to debris or dust.
   After working, if sanding dust has accumulated on the battery installation compartment and the battery, clean off the accumulated sanding dust with an air blow gun or a dry cloth before using the tool. (Fig. 14)
   NOTE

   • After cleaning, ensure that the battery can be installed and removed smoothly from the tool.
   • Using the tool when the battery is covered with sanding dust may lead to accidents such as the battery falling during use.
     Furthermore, such use may cause a malfunction or contact failure between the battery and terminals.

5. Maintenance of the motor
   The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water.

6. Storage
   Store the power tool and battery in a place in which the temperature is less than 40°C and out of reach of children.
   NOTE
   ○ When storing the tool in the case, keep sanding dust and
   debris away from it.
   Remove the battery from the tool and attach the battery cover. (Fig. 15)
   ○ Storing lithium-ion batteries.
   Make sure the lithium-ion batteries have been fully charged before storing them.
   Prolonged storage (3 months or more) of batteries with a low charge may result in performance deterioration, signifi cantly reducing battery usage time or rendering the batteries incapable of holding a charge.
   However, signifi cantly reduced battery usage time may be recovered by repeatedly charging and using the batteries two to fi ve times.
   If the battery usage time is extremely short despite repeated charging and use, consider the batteries dead and purchase new batteries.

CAUTION
In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.

Important notice on the batteries for the HiKOKI cordless power tools
Please always use one of our designated genuine batteries. We cannot guarantee the safety andperformance of our cordless power tool when used with batteries other than these designated by us, or when the battery is disassembled and modifi ed (such as disassembly and replacement of cells or other internal parts)

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with statutory/country specifi c regulation. This guarantee does not cover defects or damage due to misuse, abuse, or normal wear and tear. In case of complaint, please send the Power Tool, undismantled, with the GUARANTEE CERTIFICATE found at the end of this Handling instruction, to a HiKOKI Authorized Service Center

Information concerning airborne noise and vibration
The measured values were determined according to EN62841 and declared in accordance with ISO 4871

Measured A-weighted sound power level : 96 dB (A)
Measured A-weighted sound pressure level: 85 dB (A)
Uncertainty K : 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined according to EN62841.

Sanding steel plate:
Vibration emission value ah = 3.0 m/s2
Uncertainty K = 1.5 m/s2

The declared vibration total value and the declared noise emission value have been measured in accordance with a standard test method and may be used for comparing one tool with another.

They may also be used in a preliminary assessment of exposure.

WARNING

• The vibration and noise emission during actual use of the power tool can diff er from the declared total value depending on the ways in which the tool is used especially what kind of workpiece is processed; and
• Identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

NOTE
Due to HiKOKI’s continuing program of research and development, the specifications herein are subject to change without prior notice.

| S8360£0A
---|---
(2)<C)| INN)
76 × 533 mm
| 1| 1
| 1| 1
| 1| 1
BSL36A18
| 2| —
UC18YSL3
| 1| –
| 2| –
| 1| –
WA80| 939733
---|---
WA150| 939736
WA180| 939737
WA240| 939738
AA30| 939739
AA40| 939740
AA60| 939741
AA80| 939742
AA100| 939743
AAl20| 939744
AA150| 939745
AA180| 939746
AA240| 939747
AA320| 939748
AA400| 939749

• 76 × 533 mm

• UC18YSL3 (14.4 V–18 V)

• 337108

• 379378
  

• 379359

• 379358

• BSL36..18

• 329897

GUARANTEE CERTIFICATE

1. Model No.
2. Serial No.
3. Date of Purchase
4. Customer Name and Address
5. Dealer Name and Address (Please stamp dealer name and address)

Hikoki Power Tools Deutschland GmbH
Siemensring 34, 47877 willich, Germany
Tel: +49 2154 49930
Fax: +49 2154 499350
URL: http://www.hikoki-powertools.de

Hikoki Power Tools Netherlands B.V.
Brabanthaven 11, 3433 PJ Nieuwegein, The Netherlands
Tel: +31 30 6084040
Fax: +31 30 6067266
URL: http://www.hikoki-powertools.nl

Hikoki Power Tools (U.K.) Ltd.
25 Majestic Road, Southampton, SO16 OYT,
United Kingdom
Tel: +44 1908 660663
Fax: +44 1908 606642
URL: http://www.hikoki-powertools.uk

Hikoki Power Tools France S.A.S.
Parc de l’Eglantier 22, rue des Cerisiers, Lisses-C.E. 1541,
91015 EVRY CEDEX, France
Tel: +33 1 69474949
Fax: +33 1 60861416
URL: http://www.hikoki-powertools.fr

Hikoki Power Tools Belgium N.V./S.A.
Koningin Astridlaan 51, B-1780 Wemmel, Belgium
Tel: +32 2 460 1720
Fax: +32 2 460 2542
URL http://www.hikoki-powertools.be

Hikoki Power Tools Italia S.p.A
Via Piave 35, 36077, Altavilla Vicentina (VI), Italy
Tel: +39 0444 548111
Fax: +39 0444 548110
URL: http://www.hikoki-powertools.it

Hikoki Power Tools lbérica, S.A.
C/ Puigbarral, 26-28, Pol. Ind. Can Petit, 08227 Terrassa
(Barcelona), Spain
Tel: +34 93 735 6722
Fax: +34 93 735 7442
URL: http://www.hikoki-powertools.es

Hikoki Power Tools Österreich GmbH
IndustrieZentrum NÖ –Süd, Straße 7, Obj. 58/A6 2355
Wiener Neudorf, Austria
Tel: +43 2236 64673/5
Fax: +43 2236 63373
URL: http://www.hikoki-powertools.at

Hikoki Power Tools Norway AS
Kjeller Vest 7, N-2007 Kjeller, Norway
Tel: (+47) 6692 6600
Fax: (+47) 6692 6650
URL: http://www.hikoki-powertools.no

Hikoki Power Tools Sweden AB
Rotebergsvagen 2B SE-192 78 Sollentuna, Sweden
Tel: (+46) 8 598 999 00
Fax: (+46) 8 598 999 40
URL: http://www.hikoki-powertools.se

Hikoki Power Tools Denmark A/S
Lillebaeltsvej 90, 6715 Esbjerg N, Denmark
Tel: (+45) 75 14 32 00
Fax: (+45) 75 14 36 66
URL: http://www.hikoki-powertools.dk

Hikoki Power Tools Finland Oy
Tupalankatu 9, 15680 Lahti, Finland
Tel: (+358) 20 7431 530
Fax: (+358) 20 7431 531
URL: http://www.hikoki-powertools.fi

Hikoki Power Tools Hungary Kft.
1106 Bogáncsvirág u.5-7, Budapest, Hungary
Tel: +36 1 2643433
Fax: +36 1 2643429
URL: http://www.hikoki-powertools.hu

Hikoki Power Tools Polska Sp. z o. o.
ul. Gierdziejewskiego 1
02-495 Warszawa, Poland
Tel: +48 22 863 33 78
Fax: +48 22 863 33 82
URL: http://www.hikoki-narzedzia.pl

Hikoki Power Tools Czech s.r.o.
Modřická 205, 664 48 Moravany, Czech Republic
Tel: +420 547 422 660
Fax: +420 547 213 588
URL: http://www.hikoki-powertools.cz

Hikoki Power Tools Romania S.R.L.
Ring Road, No. 66, Mustang Traco Warehouses, Warehouse
No.1, Pantelimon City, 077145, Ilfov County, Romania
Tel: +40 371 135 109
Fax: +40 372 899 765
URL: http://www.hikoki-powertools.ro

EC DECLARATION OF CONFORMITY
We declare under our sole responsibility that Cordless Belt Sander , identifi ed by type and specifi c identifi cation code 1), is in conformity with all relevant requirements of the directives 2) and standards 3). Technical fi le at 4) – See below. The European Standard Manager at the representative offi ce inEurope is authorized to compile the technical fi le. The declaration is applicable to the product affi xed CE marking.

1. SB3608DA C363418R
2. 2006/42/EC, 2014/30/EU, 2014/35/EU, 2011/65/EU
3. EN62841-1:2015EN62841-2-4:2014+AC:2015
   EN60335-1:2012+A11:2014
   EN60335-2-29:2004+A2:2010
   EN55014-1:2006+A1:2009+A2:2011
   EN55014-2:1997+A1:2001+A2:2008

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>