BEHA BV 960 HVIT Stainless Steel Ventilator Instruction Manual

: July 13, 2024
: BEHA

BV 960 HVIT/RUSTFRI

BV 960 WHITE/STAINLESS STEEL

539660, 539610

USER INSTRUCTIONS

SAFETY INSTRUCTIONS

Please read this installation and user guide carefully before installing and using the product, paying special attention to the safety instructions.
Save these instructions for later use or for the party who may take over the product after you.
Disconnect the product from the power supply prior to cleaning or maintenance.
§ Diversion of exhaust air must be carried out in accordance with instructions issued by the appropriate authority.
§ Exhaust air must not be directed into flues that are used for fumes from items such as gas, wood or oil-burning stoves or fireplaces.
§ The distance between the stove and the product must be at least 44 cm. For gas hobs, the distance should be increased to 65 cm. Adjust accordingly if the gas hobs manufacturer recommends a higher mounting height. N.B. If the product has a stove alarm or stove guard, it must not be mounted over a gas hob. See separate instructions.
§ You must not flambé food underneath the product.
§ For safety reasons, the installation and replacement of cables or other types of connectors should only be carried out by a qualified professional.
§ If the product is to be used at the same time as products that use energy sources other than electricity, i.e., gas hobs, gas, wood or oil-burning stoves or fireplaces, etc, the room must have an adequate supply of air.
§ The product may be used by children from 8 years of age and persons with mental, sensory or physical impairment, or a lack of experience and knowledge, provided they are given information about how the product is to be used.
§ Children should not be allowed to play with the product. Children must not undertake cleaning or maintenance of the product unsupervised.
§ Accessible parts of the product may become hot when food is being prepared.
§ A fire is more likely to spread if the product is not cleaned as frequently as indicated.

Attention!
The developer or proprietor is responsible for ensuring installation is carried out correctly and complies with the applicable building regulations.

INSTRUCTIONS FOR USE

GENERAL INFORMATION

The product features LED lighting (6.5 W), aluminium filters, an EC motor and the Easy Clean system.

FUNCTIONS

Fig. 1

A. Lighting
B. Ventilation mode. The fan runs at low speed for 60 minutes.
C. Speed 1.
D. Speed 2.
E. Speed 3.
F. 1. Intensive mode. The fan runs at maximum speed for 7 minutes and then reverts to speed 3.
2. Filter guard. If the filter guard is activated (see Programming below), the LED will flash when the filter needs to be cleaned. After cleaning, press and hold button F for 2 seconds to reset the system.

Turning on the cooker hood before you start to cook prevents cooking smells spreading into the room. Adjust the speed of the cooker hood depending on the type of food you are preparing. If possible, allow the cooker hood to run at a low speed for a few minutes after you’ve finished cooking. You may also wish to run the cooker hood on the low setting when the oven is in use or after using the dishwasher.
The product is fitted with a filter guard. To activate/deactivate the filter guard, see below.

Programming

1. Start programming: press and hold buttons A and B for 3 seconds so that they both flash 3 times. Programming mode will then be active for 30 seconds.
2. Select function: press the button for the selected function to activate/deactivate the function.

Button	Functions
F	Filter guard

The LED on the button lights up when the function is activated.

3. To save a programme: press and hold buttons A and B for 3 seconds. Buttons A and B will flash twice to show that the programme has been saved.

Attention!
If the product has a stove alarm or stove guard, see separate instructions.

CARE AND MAINTENANCE

Attention!
In order to ensure operation, quality and safety after servicing and maintenance, use only original parts.

Cleaning the filter
The cooker hood should be cleaned with a damp cloth and washing-up liquid. With normal usage, the filters must be cleaned at least every other month. Clean more often after intensive use.

Fig. 2
Remove the grease filter by opening the snap retainer, Fig. 2.
Handle the filter carefully, taking care not to bend it.
Soak the filter in a solution of warm water and washing-up liquid. The filter can also be washed in a dishwasher.
Refit the grease filter after cleaning, making sure it snaps firmly into place.

Cleaning other parts
The interior of the cooker hood and removable parts should be cleaned at least twice a year.

Fig. 3
Remove the bottom plate by pushing the snap retainers in the direction of the arrows. Fig. 3

Fig. 4
Release the blower by bending the snap retainer outwards in the direction of the arrow (1) and pushing the blower away from you and down (2),Fig. 4.

Fig. 5
Release the impeller by pulling in the direction of the arrow, Fig. 5

Clean the bottom plate, blower and impeller using warm water and washing-up liquid. The blower and impeller can also be washed in a dishwasher. After washing and drying, assemble the parts in reverse order.

Fig. 6
Refit the impeller. Make sure that it is level in the groove on the motor.

Fig. 7
Refit the blower by inserting the supports in the rear of the fan (1). Bend up the blower (2).Fig. 7

Fig. 8
Make sure all the snap retainers fit onto the cooker hood lugs. Twist the blower (1) into the lugs (2). Press the blower’s snap retainer back into the lug (3).Fig. 8

Attention!
Check that the parts snap firmly into place.

REPLACEMENT OF LED LIGHTING

Fig. 9
The lighting must be replaced with an equivalent special light fixture from the manufacturer or its service agent.
The lighting is removed by pressing the snap retainers from the sides and pulling the light fixture straight down so that the lighting cable can be accessed. Fig. 9

SERVICING AND WARRANTY

TROUBLESHOOTING

Check that the fuse is intact. Go through all the functions to check what is not working. Start by disconnecting the product from the power supply and switching it on again. Check that the connector is not bent or twisted at the connection point.

Attention!
If the product has a stove alarm or stove guard, use the separate instructions for troubleshooting.

SERVICING

Fig. 10
Before contacting servicing, check the product label and note down the FUN number, S/N number and manufacturing date of the product.
The product label is located on the left side, underneath the filter/bottom plate.
Contact Beha’s customer service
e-mail:support@beha.no
If there is something wrong with the product, during the warranty period, contact Beha customer service.
The product is covered by applicable industry regulations.

ENVIRONMENT

The main raw materials used in the products are:

Metals: stainless sheet metal, galvanised sheet metal, zinc, aluminium
Plastics: polypropylene, polyamide, poly-carbonate, polybutylene terephthalate (PBT)
Glass

All components comply with the RoHS Directive.

PACKAGING AND PRODUCT RECYCLING

The packaging should be deposited at your nearest recycling point.

The symbol means that the product must not be treated as household waste. It should instead be taken to a collection point for the recycling of electrical and electronic components. By ensuring that the product is dealt with in the correct manner, you are helping to prevent the adverse environmental and health effects that could arise if the product was disposed of as regular waste. For further information on recycling, contact your local authority or waste disposal service, or the store where you purchased your product.

ECODESIGN DIRECTIVE

The product meets and is tested in accordance with the eco-design requirements of European Regulation 66/2014.

EU-DIREKTIV

This product is labeled in accordance with EU directives 2004/108/EC and 2006/95-EC on the management of electrical and electronic waste (Waste Electrical and electronic equipment WEEE).

ELECTRICAL INSTALLATION

Electrical connection for 230 V~ earthed. The product is supplied with a cable and earthed plug for connection to an earthed socket. The socket should be accessible after installation is complete. The junction box or wall socket must be accessible after installation is complete. If the connector is damaged, it must be replaced with an equivalent special cable from the manufacturer or their service agent.