Beha-Amprobe AM-520-EUR Digital Multimeter User Manual

June 13, 2024
BEHA AMPROBE

AM-520-EUR
AM-530-EUR
Digital Multimeter
User Manual

AM-520-EUR Digital Multimeter

Limited Warranty and Limitation of Liability
Your Beha-Amprobe product will be free from defects in material and workmanship for three years from the date of purchase unless local laws require otherwise. This warranty does not cover fuses, disposable batteries or damage from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on the behalf of Beha-Amprobe. To obtain service during the warranty period, return the product with proof of purchase to an authorized Beha-Amprobe Service Center or to an Beha-Amprobe dealer or distributor. See Repair Section for details. THIS WARRANTY IS YOUR ONLY REMEDY. ALL OTHER WARRANTIES – WHETHER EXPRESS, IMPLIED OR STATUTORY – INCLUDING IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, ARE HEREBY DISCLAIMED. MANUFACTURER SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages, this limitation of liability may not apply to you.
Repair
All Beha-Amprobe tools returned for warranty or non-warranty repair or for calibration should be accompanied by the following: your name, company’s name, address, telephone number, and proof of purchase. Additionally, please include a brief description of the problem or the service requested and include the test leads with the meter. Non-warranty repair or replacement charges should be remitted in the form of a check, a money order, credit card with expiration date, or a purchase order made payable to Beha-Amprobe.
In-Warranty Repairs and Replacement – All Countries
Please read the warranty statement and check your battery before requesting repair. During the warranty period, any defective test tool can be returned to your Amprobe distributor for an exchange for the same or like product. Please check the “Where to Buy” section on amprobe.com for a list of distributors near you. Additionally, in the United States and Canada, in-warranty repair and replacement units can also be sent to an Amprobe Service Center (see address below).
Non-warranty Repairs and Replacement – Europe
European non-warranty units can be replaced by your Beha-Amprobe distributor for a nominal charge. Please check the “Where to Buy” section on beha- amprobe.com for a list of distributors near you.
Beha-Amprobe
Division and reg. trademark of Fluke Corp. (USA)

Germany*
In den Engematten 14
79286 Glottertal
Germany
Phone: +49 (0) 7684 8009 – 0
beha-amprobe.de| United Kingdom
52 Hurricane Way
Norwich, Norfolk
NR6 6JB United Kingdom
Phone: +44 (0) 1603 25 6662
beha-amprobe.com| The Netherlands – Headquarters**
Science Park Eindhoven 5110
5692 EC Son
The Netherlands
Phone: +31 (0) 40 267 51 00
beha-amprobe.com
---|---|---

*(Correspondence only – no repair or replacement available from this address. European customers please contact your distributor.)
**single contact address in EEA Fluke Europe BV

  1. Flash light
  2. LCD Display
  3. Function Buttons
  4. Flash light Button
  5. Rotary Switch
  6. SELECT Button
  7. Input Terminal for voltage, diode, capacitance, Resistance, continuity and temperature measurement
  8. COM (return) terminal for all measurements
  9. Input Terminal for AC/DC mA/uA measurement
  10. Input Terminal for AC/DC A measurement to10A

Screen Display

1 The Meter selects the range with best resolution
2 Direct Current
3 Negative reading
4 Alternate Current
5 Low battery indicator
6 Data hold
7 Diode test
8 Continuity test
9 Relative zero mode
10 Non-Contact Voltage| 11 Measurement units for Resistance
12 Measurement units for Frequency
13 Measurement units for Voltage
14 Measurement units for Current
15 Measurement units for Capacitance
16 Auto Power Off
17 Maximum / minimum reading memory
18 Measurement unit for Temperature
19 Analog bar graph display
---|---

SYMBOLS

| Caution ! Risk of electric shock.
---|---
| Caution! Refer to the explanation in this Manual
| Alternating Current (AC)
| Direct Current (DC)
| The equipment is protected by double insulation or reinforced
| Earth (Ground)
| Audible tone
| Battery
| Complies with European Directives
| Conforms to relevant Australian standards
| Canadian Standards Association (NRTL/C)
| Do not dispose of this product as unsorted municipal waste.
Contact a qualified recycler.

SAFETY INFORMATION

The Meter complies with:
IEC/EN 61010-1 3rd Edition, UL61010-1 2nd Ed. and CAN/CSA C22.2 No.
61010.1-0.92 to Category III 600 Volts, Pollution degree 2
IEC/EN 61010-2-030
IEC/EN 61010-2-31 for test leads
EMC IEC/EN 61326-1
Measurement Category III (CAT III) is for measurements performed in the building installation. Examples are measurements on distribution boards, circuit- breakers, wiring, including cables, bus-bars, junction boxes, switches, socket-outlets in the fixed installation, and equipment for industrial use and some other equipment, for example, stationary motors with permanent connection to the fixed installation.
Measurement Category II (CAT II) iis for measurements performed on circuit directly connected to low voltage installation. Examples are measurements on household appliances, portable tools and similar equipments.
Warning: Read Before Using

  • To avoid possible electrical shock or personal injury, follow these instructions and use the Meter only as specified in this manual.
  • Do not use the Meter or test leads if they appear damaged, or if the Meter is not operating properly. If in doubt, have the Meter serviced.
  • Always use the proper function and range for measurements. Before rotating the function range selection switch, disconnect test probe from circuit under test.
  • Verify the Meter’s operation by measuring on a known voltage source.
  • Do not apply more than the rated voltage, as marked on the Meter, between the test probe or between any test probe and earth ground.
  • Use the Meter with caution for voltages above 30 Vac rms, 42 Vac peak, or 60 Vdc. These voltages pose electrical shock hazards.
  • Disconnect circuit power and discharge all high-voltage capacitors before testing resistance.
  • Do not use the Meter around explosive gas or vapor.
  • When using the test leads, keep your fingers behind the finger guards.
  • Remove test leads from the Meter before opening the Meter case or battery door.

UNPACKING AND INSPECTION

Your shipping carton should include:
1 AM-520-EUR or AM-530-EUR
1 Pair of test leads
1 Temperature probe
1 Velcro strap
1 9V (6F22) battery (installed)
1 User manual
1 Carrying case
If any of the items are damaged or missing, return the complete package to the place of purchase for an exchange.

FEATURES

AM-520-EUR is designed for HVAC applications with key functions such as temperature, micro amps used for flame sensor troubleshooting, as well as and capacitance to check the motor startup capacitors. The AM-520-EUR measures a complete range of electrical parameters and features a built in flashlight, a “third hand” probe holder and VoltTect non-contact voltage detection. Safety rated to CAT III 600V.
AM-530-EUR is the fully-featured multimeter of choice for the professional electrical contractor. Measure and verify presence of voltage in order to connect equipment or to perform repairs, run new wiring, check continuity of electrical connections, identify blown fuses, troubleshoot motors or check transformers. The AM-530-EUR features Truerms sensing to accurately measure voltage on systems affected by harmonics, a built in flashlight to detect wire colors in the dark, a “third hand” probe holder and non-contact voltage detection. Safety rated to CAT III 600V.

  • Measurements: Voltage up to 600VAC and 600VDC, AC/DC current, Resistance, Frequency, Capacitance, Temperature.

  • Frequency, Capacitance, Duty Cycle for troubleshooting applications

  • Special Functions:
    – Non-contact Voltage Detection
    – Audible continuity
    – Diode Test

  • Backlit LCD display with analog bar graph

  • Events:
    – Data hold
    – MAX / MIN Memory
    – Relative zero mode

  • Built in work light (flashlight)

  • Built in test leads storage and “third hand holder”

  • Auto and Manual ranging

  • Auto power off

  • Low battery warning

  • Velcro strap to hang a meter

  • Safety: CAT III 600V

MAKING MEASUREMENT

  1. Use the proper function and range for measurements.

  2. To avoid possible electrical shock, personal injury or damages to the Meter, disconnect circuit power and discharge all high-voltage capacitors before testing resistance and diode.

  3. Connecting test leads:
    • Connect the common (COM) test lead to the circuit before connecting the live lead;
    • After measurement, remove live lead before removing the common (COM) test lead from the circuit

  4. Symbol “OL” is displayed on LCD when the measurement is out of range.

Rotary Switch Positions

Switch Position Measurement Function
AC or DC voltage measurement (use SELECT button for switching to AC or DC).
Resistance measurement
Voltage measurement of diode PN junction
Continuity measurement
Capacitance measurement
Hz Frequency measurement
°C °F Temperature measurement
NCV Non-contact voltage
AC or DC current measurement (use SELECT button for switching to AC or DC).

Function Buttons

Button Measurement Function
SELECT Switching AC or DC. Press the yellow SELECT button to select

alternate measurement functions on the rotary switch.
| Display freezes present reading / press 2 sec to turn on LCD backlight.
| Relative zero mode
RANGE| Manual or Auto range switching. The default setting is Auto ranging, press to switch to manual ranging (selectable resolutions). Press for 2 sec to return to auto ranging.
MAX/MIN| Maximum / minimum reading memory.
| Flash light

Press to enable the function when at relevant rotary switch function.
Auto Power OFF
Auto power off: approx. 15 minutes.
When the Meter is in auto power off mode, press any button to resume normal operation.
Measuring AC and DC Voltage
Press SELECT button to select AC/DC voltage measurement function.
To avoid personal injury or damage to the Meter, do not apply voltage higher than 600Vac and 600Vdc. Measuring AC and DC Current
Press SELECT button to select AC or DC current measurement function.
To avoid personal injury or damage to the Meter:

  1. Do not attempt to make an in-circuit current measurement when the open-circuit potential to earth ground exceeding AC 600V or DC 600V
  2. Switch to proper function and range for your measurement.
  3. Do not place the test probe in parallel with a circuit when the test leads are connected to the current terminals.
  4. Connect the test leads to the correct input A/mA μA current terminal and to the circuit before powering the circuit under test.
  5. For current range from 8-10A, do not measure current for more than 20 minutes. Wait for 10 minutes before taking another measurement
  6. After measurement, switching OFF the circuit’s power before removing test leads from the circuit.

Measuring Resistance
Disconnect circuit power and discharge all high-voltage capacitors before testing resistance. Note: On a higher resistance measurement (>1MΩ), the measurement may take a few seconds to get stable reading.
Over range or open circuit indication: OL
Measuring Continuity
Disconnect circuit power and discharge all high-voltage capacitors before testing continuity. Measuring Diode
Disconnect circuit power and discharge all high-voltage capacitors before testing diode. Measuring Capacitance
Disconnect circuit power and discharge all high-voltage capacitors before testing capacitance. Measuring Frequency
To avoid personal injury or damage to the Meter, do not apply voltage higher than 600V. Measuring Temperature °C / °F

  1. To avoid personal injury or damage to the Meter, do not apply thetemperature probe to any live conductive parts.
  2. Temperature sensor K type (nickel-chromium/nichrosi) thermocouple is suitable for temperature measurement below 230°C (446°F).

Measurement steps:
Step 1: Turn the rotary switch to °C or °F position. The display will show “OL”.
Step 2: Connect the temperature probe (K type) to the Meter and to the surface to be measured. Non-Contact Voltage Sensing

  1. To avoid personal injury or damage to the Meter, do not test on uninsulated high voltage wires.
  2. Buzzer will sound and screen will display “OL” when sensing AC voltage between 90V and 600V
  3. Do not test on hazardous live wires higher than AC 600V
  4. Before and after hazardous voltage measurements, test the Meter by approaching to a known source such as a line AC voltage or outlet to determine proper operation. See below figure.

Buzzer will sound when the detected voltage is ≥ 90V, and the buzzer will be on.The distances between the wire and the meter should be ≤ 8mm.
At NCV mode, LCD will display OL. No test lead connection are required for NCV measurement.

SPECIFICATION

Ambient temperature: 73.4°F ±9 (23°C ±5°C); Relative temperature: ≤ 75%
Accuracy: ±(% of reading + digits)
Maximum voltage between input terminal and earth ground: AC 600Vrms or DC 600V
Fuse for mA µA input: F1 fuse, 0.5A H 1000V fast-fuse, (6.3×32)mm
Fuse for 10A input: F2 fuse, 11A H 1000V fast-fuse, (10×38)mm
Maximum display: Digital 3999 counts, updates 3/sec. Frequency: 9999 counts.
Analog pointer display: 41 segments, updates 30 times/sec.
Over-range indication: OL
Range: Automatic and Manual
Altitude: Operating 2000m
Operating temperature: 0°C ~ +40°C (32°F ~ 104°F)
Relative humidity: 0°C ~ +30°C (32°F ~ 86°F) ≤ 75%; +30°C ~ +40°C (86°F ~ 104°F) ≤ 50%
Storage temperature: -10°C ~ +50°C (14°F ~ 122°F)
Electromagnetic compatibility: In an RF filed of 1V/m = Specified accuracy 5%
Battery: 9V, 6F22, NEDA1604 or equivalent
Low battery indication:
Dimensions (L x W x H): 182 mm x 90 mm x 45 mm (7.2 in x 3.5 in x 1.8 in)
Weight: Approx. 354g (0.78lb) with batteries installed
1. DC Voltage Measurement

Range Resolution Accuracy
400.0mV 0.1mV ± (0.8%+3LSD)
4.000V 1 my ± (0.8%+1 LSD)
40.00V 10mV
400.0V 100mV
600V 1V ±(1.0%+3LSD)

Input impedance: About 10M ;
(Input impedance is ≤ 3G Ωexcept DC 400mV range)
Overload protection: ±600V
2. AC Voltage Measurement

Range Resolution Accuracy
400.0mV 0.1mV ±(1.2%+3LSD)
4.000V 1mV ±(1.0%+3LSD)
40.00V 10mV
400.0V 100mV
600V 1V ±(1.2%+3LSD)

Note: Manual range only for 400.0mV range.
Input impedance: Around 10M Ω
Frequency response: 45Hz ~ 400Hz
AM-520-EUR : Average sensing, rms indication.
AM-530-EUR: True RMS.
Overload protection: 600Vrms
3. Resistance Measurement

Range Resolution Accuracy
400.0Ω 0.1Ω ±(1.2%+2LSD)
4.000kΩ ±(1.0%+2LSD)
40.00kΩ 10Ω
400.0kΩ 100Ω
4.000MΩ 1kΩ ±(1.2%+2LSD)
40.00MΩ 10kΩ ±(1.5%+5LSD)

400Ω range: Measured value = (Measured display value – Short-circuiting value of probe)
Open circuit voltage: Around 0.5V
Overload protection: 600Vrms
4. : Circuit ON/OFF : Diode measurement

Range Resolution Accuracy
0.1Ω Open circuit voltage is around 0.5V.

Resistance >150Ω , buzzer will not sound.
Resistance ≤ 10Ω , buzzer will sound.
| 1mV| Display range is 0V to 2.0V. Normal voltage is around 0.5V to 0.8V for silicon PN junction.

Overload protection: 600V
5. Capacitance Measurement

Range Resolution Accuracy
40.00nF 10pF ±(3%+10LSD) under REL status
400.0nF 100pF ±(3%+5LSD) under REL status
4.000pF 1nF
40.00pF 10nF ±(3%+5LSD)
400.0pF 100nF ±(4%+5LSD)
4000pF 1pF For reference only

Overload protection: 600V
6. Frequency Measurement

Range Resolution Accuracy
10Hz~10MHz 0.01Hz~0. 01MHz ±(0.1%+4LSD)

Overload protection: 600Vrms
7. DC Current Measurement

Range Resolution Accuracy
NA 400.0pA 0.1pA
4000pA 1pA
mA 40.00mA 10pA
400.0mA 0.1mA
A 4.000A 1 mA
10.00A 10mA

Overload protection:
mA /µA range:F1 fuse, 0.5A H 1000V fast-fuse, ( Φ 6.3×32)mm
10 A range:F2 fuse, 11A H 1000V fast-fuse, ( Φ 10×38)mm
8. AC Current Measurement

Range Resolution Accuracy
NA 400.OpA 0.1pA
4000pA 1pA
mA 40.00mA 10pA
400.0mA 0.1mA
A 4.000A 1 mA
10.00A 10mA

Frequency response: 45Hz ~ 400Hz
AM-520-EUR : Average sensing, rms indication.
AM-530-EUR: True RMS.
Overload protection:
mA /µA range:F1 fuse, 0.5A H 1000V fast-fuse, ( 6.3×32)mm
10 A range:F2 fuse, 11A H 1000V fast-fuse, ( 10×38)mm
9. Temperature Measurement

Range Resolution Accuracy
-40 – 0°C 0.1°C @< 400°C
1°C @ 400°C ±(10%+4°C)
>0 – 100°C ±(1.2%+3°C)
>100 – 1000°C ±(2.5%+2°C)
-40 – 32°F 0.1°F @< 752°F
1°F © 752°F ±(20%+6°F)
>32 – 212°F ±(1.8%+6°F)
>212 – 1832°F ±(2.5%+4°F)

Overload protection: 600V
K type (nickel-chromium/nichrosi) thermocouple must be used for temperature measurement.

MAINTENANCE AND REPAIR

If the Meter fails to operate, check battery, test leads, etc., and replace as necessary.
Double check the followings:

  1. Replace the fuse or battery if the meter does not work.
  2. Review the operating instructions for possible mistakes in operating procedure.

Quick check on 0.5A FUSE:
Step 1: Turn the rotary switch to Ω function.
Step 2: short-circuit E /V/Ω/Hz terminal and mA/μA terminal.
Resistance reading ≤ 1M Ω : the fuse is OK
Resistance reading “OL”: the fuse is open. Replace the fuse as specified.
Quick check on 10A FUSE:
Step 1: Turn the rotary switch to Ω function.
Step 2: short-circuit E/V/Ω/Hz terminal and A terminal.
Resistance reading ≤ 0.5Ω : the fuse is OK.
Resistance reading “OL”: the fuse is open. Replace the fuse as specified. Except for the replacement of the battery, repair of the meter should be performed only by a Factory Authorized Service Center or by other qualified instrument service personnel.
The front panel and case can be cleaned with a mild solution of detergent and water. Apply sparingly with a soft cloth and allow to dry completely before using. Do not use aromatic hydrocarbons, Gasoline or chlorinated solvents for cleaning.

BATTERY AND FUSE REPLACEMENT

WARNING
To avoid shock, injury, or damage to the Meter:
Disconnect test leads before opening case.
Use ONLY fuses with the amperage, interrupt, voltage, and speed ratings specified.
Replacing BATTERY follow below steps:

  1. Disconnect the test lead probe from measuring circuit.

  2. Turn the Meter to OFF position.

  3. Remove the screws from the battery cover and open the battery cover

  4. Remove the batteries and replace with one 9V (6F22) or equivalent. The battery cover provides the correct polarity fitting construction design.
    Install the battery in the battery cover.

  5. Put the battery cover back and re-fasten the screw.
    Battery: 9V (6F22) Battery or equivalent

Replacing FUSE follow below steps:

  1. Disconnect the test lead probe from measuring circuit.
  2. Turn the Meter to OFF position.
  3. Remove the screws from the enclosure and open the enclosure.
  4. Remove the broken fuse and replace with new specified fuse.
  5. Put the enclosure back and re-fasten the screw.

Fuse ratings:
mA /µA input terminal: F1 fuse, 0.5A H 1000V fast-fuse, (Φ 6.3×32)mm
10 A input terminal: F2 fuse, 11A H 1000V fast-fuse, (Φ 10×38)mm Visit beha- amprobe.com for

  • Catalog
  • Application notes
  • Product specifications
  • User manuals

beha-amprobe.com
c/o Fluke Europe BV
Science Park
Eindhoven 5110
NL-5692 EC Son
Tel.: +49 (0) 7684 8009 – 0

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals