Ulanzi F32 Camera Speedlite User Manual

Ulanzi F32 Camera Speedlite

Foreward
Thank you for purchasing

Instructions

• Please read this product manual carefully.
• Keep this product manual. Always: include this product manual when passing the products on to third parties.
• Heed all warnings and follow all instructions in this product manual.
• WARNING Do not place the product In• place where there domical to proactive product from cam,slan, cam,slan may cause the product to malfunction.
• Use only a microfiber and dry cloth for cleaning the product.
• Operate carefully to not cause any damage by dropping or physical shocking it.
• Do not leave the product in excessive heat, high temperatures can cause the product to malfunction.
• Please have the product checked by the authorized service or agent if your product has some problems. Please note that this warranty does not apply to repair arising out of the malfunction of unauthorized disassembly, although you may request such repairs on a chargeable basis.
• Use of original cable accessories is recommended. Please note that warranty does not apply to repairs arising out of the malfunction of non-original accessories1 although you may request such repairs on a chargeable basis.
• The product by RoHS and CE. Please operate the product in full compliance with the operation standards. Please note that this warranty does not apply to repairs arising from malfunction, although you may request such repairs on a chargeable basis.
• The instructions and information in this manual are based on thorough, controlled company testing procedures. Further notice will not be given if the design and specifications change.

Intended Use

• The user has read the instructions of this manual.
• The user is using the products within the operating conditions and limitations described in this product manual.
• “Improper use” means using the products other than as described in these instructions or under operating conditions which differ from those described herein.

Packing List

Product Overview

Instructions

1. The back of the flash is in the same direction as the back of the camera, Push the base into the hot shoe and tighten the knob.

2. Turn on the switch, and after the indicator light is on, press the test button for a test flash.

3. The brightness adjustment level of the flash is 0-100%, After full power flashing, it takes 3-4 seconds to power back. Continuous full power flashing will trigger overheating protection.

4. Flash duration is 1/200-1/10000 second, The lower the power, the shorter the flash duration, forming a high-speed flash and a faster return rate.

   • Low power output
     High speed flash with over 1/3000 seconds is suitable for indoor close-up photography.Freeze moment in dark or completely black environment Like water droplets splashing

   • High power output
     About 1/200 second, suitable for night photography or daytime backlight photography to illuminate the subject

5. The maximum speed for synchronizing flash and shutter is 1/250 second, Single trigger point, does not support TTL and high-speed synchronization.
   Use shutter 1/125 ,aperture F8 ,ISO 100 test at full power The effective exposure distance is 4 meters, and the guide number is 32.
   Increasing the aperture or increasing IS O can increase the effective flash distance, Focal length of 18 mm-85 mm is good.

6. Press the M button to switch channels, CHO and CH1, This function requires a flashing wireless trigger.

7. When taking photos, multiple flash lights can be used as needed, The farthest trigger distance is 24 meters.

• Each channel of the trigger can be connected to multiple F32 flash.
• After installing the trigger onto the camera’s hot shoe, the hot shoe on the trigger is Connect to camera. You can install and use various single contact flashlights and no need to turn on power.
• After the trigger is turned on, for example when the channel is CHO, the channel of F32 on the trigger is CH1, it still can trigger the flash.

Product Specification

The data is the average value of laboratory tests, with slight differences in actual use.

Wireless trigger Functional diagram

Wireless trigger Operating instructions

1. Install two AAA batteries, push the switch O ) to “ON”. ‘, and press the flash test button, If the signal light is on, the signal is sent normally.
2. Direct matching of the A35 and the wirtless trigger,for example, turned on the A35 and the channel identifier on the upper left of the screen is CHO, the trigger is also the same, and they are on the same channel. Press the test button to test.
3. Press the M button on the flash to switch channels, the trigger switch channel too, press the test button once again.
4. The wireless trigger needs to be installed on the camera’s hot shoe and fixed with a locking knob for use. Turn off the switch before installation.
5. The side of the wirtless trigger is trigger cable socket, Some old models of cameras only have cold shoe mouth. Unable to trigger Need to use the cable to trigger, different cameras have different Corone% cable port, purchase as needed.

Specification parameters

FCC Warning Statement

Changes or modifications riot expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment hes been tested and found to comply with the limits for a Clan B digital device, pursuant to Part 16 of the FCC Rules. These limits ere designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television, reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference By one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radiofTV technician for help.

This device complies with part 15 of lhe FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful Interference.
(2) this device must accept any interference received, including interference that may cause undesired operation.

Tha device has been evaluated to meet general RF exposure requirements. The device can be used In portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>