Ulanzi AM18 Wireless Microphone Pro Instruction Manual

****

Ulanzi AM18 Wireless Microphone Pro

Foreword
Thank you for purchasing from ULANZI. Please read this manual before using.

Product Features

• Dual channel wireless radio system, support simultaneous recording of two audio sources
• 2.4G wireless transmission technology, stable signal transmission, effective distance up to 100 meters )
• Transmitter built-in high-quality omnidirectional microphone
• The transmitter has a built-in 8GB storage, which can record audio for up to 14 hours
• The receiver is equipped with a TFT touch screen, which can display real-time recording volume, battery power and other information
• Support stereo, mono, safe track three radio modes
• The receiver can be connected to the camera or mobile phone through the expansion interface
• The receiver has an independent monitoring interface, and the monitoring volume can be set through the screen
• The standard charging case can charge the transmitter and receiver at the same time

Applicability

Designed for Live Streaming, VLOG, Videography, Interviews and more.

Packing List

• Charging Case
• Transmitter
• Receiver-
• Accessory Cord•
• Storage Bag
• Windscreen-
• Instruction Manual-
• Black PC Spacer

Technical Parameters

Charging Case Parameters

• Input Voltage: DC4.8~5.4V
• Standby Current: 10uA-20uA
• Charging Time: About 120 minutes
• Charging : Type-C charging cable
• Unit Size: 9758.557.9mm
• Input power: 5V/2A
• Charging Current: about 1500mA
• Battery Life: Support 1 round cyclic charging
• (transmitter2, receiver1)
• Battery Parameters: 1000mAh*2 (with protection board)
• Charging Compartment unit weight: 128.5g

Transmitter Parameters

• Sampling Rate: 48Khz/16bit
• Frequency Range: 2.4GHz
• Battery Capacity: 300mAh(with protective plate)
• Transmission Delay Time: 24ms
• Frequency Response Range: 20-20kHZ
• Operating Time: About 14 hours
• Transmission Distance: barrier-free >100M (about 5 hours when local recording is on)
• Charging Input Voltage: DC4.8~5.4V
• Charging Time: About 90 minutes
• Sensitivity: -36dB+2dB
• Weight: 23g
• Signal-noise Ratio: 94dB
• Size: 35.615.545.8mm
• Charging Method: Pogo pin/Type-C

Receiver Parameters

• Sampling Rate:48Khz/16bit
• Frequency range:2.4GHz
• Transmission Delay time: 24ms
• Battery capacity:300mAh(with protective plate)
• Screen Operation Mode:touch
• Operating time:About 6 hours
• Transmission Distance: barrier-free ≥ 100M Charging time:About 90 minutes
• Charging Input Voltage:DC4.8~5.4V
• Weight:34.5g
• Sensitivity:-36dB+2dB
• Size:35.615.545.8mm
• Signal-noise Ratio:94dB
• Charging Method:Pogo pin/Type-C

This data comes from Ulanzi laboratory test data, the specific usage time is subject to the actual situation!

Function  schematic

Transmitter Functional Description Receiver Functional Description Charging case function description

Camera Connection Instructions Windscreens installation instructions
Align the plastic buckle of the windscreen with the groove of the transmitter, insert it downward, and rotate it clockwise 90° to fix it . Gasket Instructions
For different cold shots port, choose a gasket with a thickness suitable, tear off the adhesive sticker, and stick it on the cold boot opening.
Safety Alert
To avoid personal injury or property damage that may be caused by electric shock, high temperature, fire, radiation, explosion, mechanical hazards, and improper use, please read and abide by the following items carefully before using this product:

1. When using the product, please confirm whether the power of the connected device matches the product and adjust the volume of the device reasonably. Do not use it for a long time under the power of the product and high volume, so as not to cause abnormalities in the product;
2. If any abnormality (such as smoke, peculiar smell, etc.) is found during use, pleas  immediately turn off the power switch and unplug the power plug, and then send the product to the dealer for repair;
3. This product and accessories should be placed in a dry and ventilated place indoors. Donot store it in a humid or dusty environment for a long time. During use, avoid close to fire sources, rain, water, excessive collision, throwing, vibration of the machine and cover ventilation hole to avoid damaging its function;
4. When using this product, you must abide by the relevant safety regulations. Laws and regulations clearly prohibit the use of the product, so as not to cause accidents;
5. Please do not disassemble, refit or repair by yourself to prevent personal injury. If you have any questions or service needs, please contact your local dealer for follow-up.

FCC Caution

Any Changes or modifications not expressly approved by thee party responsible for compliance could void the user’s authority to operate the equipment.This device complies with part 15 of the FCC Rules. Operation is :subject to the following two conditions: (1) This device may not cause harmfulinterference, and (2) this device must accept any interference received, ircluding interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limitsset forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0 mm between the radiator& your boby.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and canadiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technicianfor help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>