TELTONIKA FMC250 GPS Tracker User Manual

TELTONIKA FMC250 GPS Tracker User Manual

Advanced watter resistant tracker with CAN data reading feature

DEVICE YOUR KNOW

TOP VIEW

BOTTOM VIEW (WITHOUT COVER)

TOP VIEW (WITHOUT COVER)

PIN OUT

range: 030 VDC
3| DIN2-N/ AINT| Digital output, channel 3 with ground sense / Analoginput, chanel 1. Input range: 0-30 V DC
4| DIN 1| Digital input, channel 1
5| CAN 2 L| CAN2 Low
6| CAN 1 L| CAN 2 Low
7| G N D (-)| Ground
8| DO UT 1| Digital output, channel 1. Open
collector output. Max. 3,3 A DC.
9| DOUT 2| Digital output, channel 2. Open
collector output. Max. 3,3 A DC.
10|  1WIRE POWER| +3,8 V output for 1–Wire devices.
11| 1WIRE DATA| CAN 2 High
12| CAN 1H| CAN 1 High

FMC250-QJIBO WIRING SCHEME

SET UP YOUR DEVICE

HOW TO INSERT MICRO-SIM CARD AND CONNECT THE BATTERY

1. **PARTLY CLOSED DEVICE

** You will receive your device partly closed.

2. Cover REMOVAL
   
   Gently remove top and bottom covers.

3. SIM CARD INSERT
   
   Insert SIM card as shown with PIN request disabled or read our Wiki¹ how to enter it later in Teltonika Configurator². Make sure that Micro-SIM card cut- off corner is pointing outward from slot. SIM slot 1 is closer to PCB, SIM slot 2 is the top one.

4. wiki.teltonika-gps.com/view/FMC230_Security_info

5. wiki.teltonika-gps.com/view/Teltonika_Configurator

6. **BATTERY CONNECTION

Connect battery** as shown to device. Position the battery in place where it does not obstruct other components.

5. ATTACHING COVER BACK
   
   After configuration, see “PC Connection (Windows)¹”, attach device top and bottom cover back and press them twice to the full closure.
   “PC Connection (Windows)

6. COMPLETELY CLOSED DEVICE
   
   Make sure that product casing is closed correctly.

IMPORTANT!

This device has an IP67 casing with a two-phase closing, that ensures reliable protection and ease of use. Please make sure that product casing corner clips are fixed tightly and cable is connected to the device in order to maintain the degree of IP67 protection.

PC CONNECTION (WINDOWS)

1. Power-up FMC250 with DC voltage (10 – 30 V) power supply using supplied power cable. LED’s should start blinking, see “LED indications™.
2. Connect device to computer using Micro-USB cable or Bluetooth® connection:
   • Using Micro-USB cable
   • You will need to install USB drivers, see *“How to install USB drivers (Windows}”**
   • Using Bluetooth®
   • FM C 250 Bluetooth is enabled by defautt. Turn on Bluetooth® connection on your PC, then select Add Bluetooth® or other device > Bluetooth®. Choose your device named
   • “FMC250_last_7_imei_digits”, without LE in the end. Enter default password 5555, press Connect and then select Done.
3. You are now ready to use the device on your computer.
4. wiki.teltonika-gps.com/view/FMC250_LED_status
5. Page 7, “How to install USB drivers”

HOW TO INSTALL USB DRIVERS (WINDOWS)

1. Please download COM port drivers from here!.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.
6. teltonika-gps.com/downloads/en/FMC250/TeltonikaCOMDriver.ap

CONFIGURATION (WINDOWS)

At first FMC250 device will have default factory settings set. These settings should be changed according to the users needs. Main configuration can be performed via Teltonika Configurator1 software. Get the latest Configurator version from here2. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.

1. wiki.teltonika-gps.com/view/Teltonika_Configurator
2. wiki.teltonika-gps.com/view/Teltonika_Configurator_versions

MS .NET REQUIREMENTS

Operating system| MS .NET Framework version| Version| Links
Windows Vista Windows 7 Windows 8.1Windows 10| MS .NET Framework 4.6.2|  32 and 64 bit|  www.microsoft.com

1. dotnet.microsoft.com/en-us/download/dotnet-framework/net462

Downloaded Configurator will be in compressed archive. Extract it and launch Configurato r. exe. After launch software language can be changed by ducking in the right bottom corner.

Configuration process begins by pressing on connected device.

After connection to Configurator Status window will be displayed.

Various Status window¹ tabs display information about GNSS, GSM³, I/O4, Maintenance . 5 and etc. FMC250 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:

• Load from device – loads configuration from device.
• Save to device – saves configuration to device.
• Load from file – loads configuration from file.
• Save to file – saves configuration to file.
• Update firmware – updates firmware on device.
• Read records – reads records from the device.
• Reboot device – restarts device.
• Reset configuration – sets device configuration to default.

Most important configurator section is  GPRS  – where all your server and GPRS settings can be configured and Data Acquisition – where data acquiring parameters can be configured.
More details about FMB130 configuration using Configurator can be found in our Wiki.

1. wiki.teltonika-gps.com/view/FMC250_Status_info
2. wiki.teltonika-gps.com/view/FMC250_Status_info#GNSS_Info
3. wiki.teltonika-gps.com/view/FMC2501_Status_info#GSM_Info
4. wiki.teltonika-gps.com/view/FMC250_Status_info#1.2FO_Info
5. wiki.teltonika-gps.com/view/FMC250_Status_info#Maintenance
6. wiki.teltonika-gps.com/index.php?title=FMC250_GPRS_settings
7. wiki.teltonika-gps.com/index.php?title=FMC250_Data_acquisition_settings
8. wiki.teltonika-gps.com/index.php?title=FMC250_Configuration

QUICK SMS CONFIGURATION

Default configuration has optimal parameters present to ensure best performance of track quality and data usage.

Quickly setup your device by sending this SMS command to it:

Note: Before SMS text, two space symbols should be inserted.

GPRS SETTINGS:

1. 2001 – APN

2. 2002 – APN username (if there are no APN username, empty field should be left)

3. 2003 – APN password (if there are no APN password, empty field should be left)
   SERVER SETTINGS:

4. 2004- Domain

5. 2005- Port

6. 2006 – Data sending protocol (0~ TCP, 1~ UDP)
   

Default configuration settings

Movement and ignition detection:

• VEHICLE MOVEMENT
  will be detected by  accelerometer
  

• IGNITION
  will be detected by vehicle power voltage between 13,2 – 30 V
  

DEVICE MAKES A RECORD ON STOP IF:

• 1 HOUR PASSES
  while vehicle is stationary and ignition is off
  

RECORDS SENDING TO SERVER:

• EVERY 120 SECOND
  it is sent to the server If device has made a record

DEVICE MAKES A RECORD ON MOVING IF ONE OF THESE EVENTS HAPPEN:

• PASSES
  300 seconds

• VEHICLE DRIVES
  100 meters

• VEHICLE TURNS
  10 degrees

• SPEED DIFFERENCE
  between last coordinate and current position is greater than 10 km/h

After successful SMS configuration, FMB130 device will  synchronize time and  update records  to  configured server.  Time intervals and default I/O elements can be changed by using Teltonika Configurator or SMS parameters.

1. wiki.teltonika-gps.com/view/Teltonika_Configurator
2. wiki.teltonika-gps.com/view/Template:FMC_Device_Family_Parameter_list

MOUNTING RECOMMENDATIONS

CONNECTING WIRES

• Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the wires.
• The connections should not be seen very clearly. Iffactory isolation was removed while connecting wires, it should be applied again.
• If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc, additional isolation should be applied.
• Wires cannot be connected to the board computers or control units.

CONNECTING POWER SOURCE

• Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on the car model, this may happen in 5 to 30 minutes period.
• When the module is connected, measure the voltage again to make sure it did not decrease.
• It is recommended to connect to the main power cable in the fuse box.
• Use 3 A , 125 V external fuse.

Connecting ignition wire

• Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
• Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
• Check if power is still available when you turn off any of vehicles devices.
• Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.

CONNECTING IGNITION WIRE

• Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
• If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
• For better contact scrub paint from the spot where loop is going to be connected.

LED INDICATIONS

mode
Blinking fast constantly| Device firmware is being flashed

STATUS LED INDICATIONS

CAN STATUS LED INDICATIONS

Basic characteristics

MODULE

Name| FMC250-Q)IB0: Quectel EGI15U-EU
Technology| GSM, GPRS, GNSS, BLUETOOTH LE, LTE
GNSS.
GNSS.| GPS, GLONASS, GALILEO, BEIDOU,  QZ55,AGPS
Receiver| Tracking: 33
Tracking sensitivity| -165 dBM
Accuracy| <3 m
Hot start| <1 s
Warm start| <25 s
Cold start| <35 s
CELLULAR
Technology|                       LTE Cat 1, GSM
26 bands| FMC250-Q)IB0: GSM: B2/B3/B5/BS
46 bands| FMC250-Q)IBO: LTE FDD: B1/B3/BS/  B7/B8/B20/B28
Data ata transfe transfer| LTE: LTE FDD: Max 10Mbps (DL)/ Max 5Mbps (UL)GSM: GPRS: Max 85.6Kbps (DL)/ Max 85.6Kbps (UL)
Data support| SMS (text/data)
Transmit power| Class 5 for GSM900: 36dBmClass 3 for DCS1800: 33dBmClass 3 for LTE-FDD: 25.7dBmBluetooth: 5.56dBmBluetooth® LE: -3.17dBm
POWER
Input voltage range| 10-30 V DC with overvoltage  protection
Back-up battery| 170 mAh Li-lon battery 3.7 V (0.63  Wwh)
Internal fuse|                3A125V
Power Consumption| At 12V < 6 mA (Ultra Deep Sleep¹)At 12V 8 mA (Deep Sleep²)At 12V 11 mA (Online Deep Sleep³)At 12V <20 mA (GPS Sleep¹)At 12V 35 mA (nominal with no load)At 12V 250 mA Max. (with full Load/Peak)
BLUETOOTH® TECHNOLOGY
Specification| 40+LE
Supported peripherals| Temperature and Humidity sensor,Inateck Barcode Scanner, Universal Bluetooth® LE sensors support
INTERFACE
Digital Inputs|                        FMC250-Q)IB0: 3
Negative Inputs| FMC250-QJIBO: 1 (Digital Input 2)
Impuls Inputs| FMC250-QJIBO: 2 (Digital Input 1, Digital Input 2)
Analog Inputs| FMC250-QJIBO: 2

1. wiki.teltonika-gps.com/view/FMC250_Sleep_modes#Ultra_Deep_Sleep_mode
2. wiki.teltonika-gps.com/view/FMC250_Sleep_modes#Deep_Sleep_mode
3. teltonika-gps.com/view/FMC250_Sleep_modes#Online_Deep_Sleep_mode
4. wiki.teltonika-gps.com/view/FMC250_Sleep_modes#GPS_Sleep_mode
5. Steltonika.lt/product/bluetooth-sensor/
   Digital outputs| FMC250-QJIBO: 2
   ---|---
   CAN interfaces| 2
   1-Wire| 1 (1-Wire data)
   GNsS antenna| Internal High Gain
   GSM antenna| Internal High Gain
   usB| 2.0 Micro-USB
   LED indication| 3 status LED lights
   SIM| Micro-SIM or Esim
   Memory| 128MB internal flash memory
   PHYSICAL SPECIFICATION
   Dimensions| 705 x 67,0 % 25,6 mm (Lx W x H)85,0 x67,0 % 25,6 mm (Lx W x H)(length with connector socket)
   Weight| 7358
   OPERATING ENVIRONMENT
   Operating temperature(without battery)| -40°Ct0+85°C
   Storage temperature (without battery)| -40 °C to +85 °C
   Operating temperature (with battery)| 20 °Cto +40 °C
   Storage temperature (with battery)| 20 °Cto +45 °C for 1 month
   -20°C to +35 °C for 6 months
   Operating humidity| 5% to 95% non-condensing
   Ingress Protection Rating| 1P67
   Battery charge temperature| 0°Cto +45°C
   Battery storage temperature| -20°C to +45 °C for 1 month
   20 °C to +35 °C for 6 months
   FEATURES
   CAN Data| Fuel Level (Dashboard), Total fuel consumption, Vehicle speed (wheel),
   ehicle driven distance, Engine speed (RPM), Accelerator pedal
   position
   Sensors,| Accelerometer
   Scenarios| Green Driving, Over Speeding detection, Jamming detection, GNSS Fuel Counter, DOUT Control Via Call, Excessive Idling detection, Immobilizer, iButton Read Notification, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, Trip®
   Sleep modes S| GPS Sleep, Online Deep Sleep, Deep
   Sleep, Ultra Deep Sleep’
   Configuration and firmware update| FOTA Web, FOTA, Teltonika Configurator10 (USB, Bluetooth® wireless technology), FMBT mobile application¹¹ (Configuration)
   SMS| Configuration, Events, DOUT control, Debug
   GPRS commands| Configuration, DOUT control, Debug
   Time Synchronization| GPS, NITZ, NTP
   Ignition detection| Digital Input 1, Accelerometer, External Power Voltage, Engine
6. wiki.teltonika-gps.com/view/FMC250_Sleep_modes
7. wiki.teltonika.lt/view/FOTA_WEB
8. wiki.teltonika.lt/view/FOTA
9. wiki.teltonika.lt/view/Teltonika_Configurator
10. teltonika.lt/product/fmbt-mobile-application/

ELECTRICAL CHARACTERISTICS

CHARACTERISTIC DESCRIPTION

| VALUE
---|---
ML| YR| MAX| UM
SUPPLY VOLTAGE
Supply Voltage(RecommendedOperating Conditions)| ‘10| +30| v
DIGITAL OUTPUT (OPEN DRAIN GRADE)| 120| uA
Drain current (Digital Output ON, Recommended Operating Conditions)| 0.1| 0.5| A
Static Drain-Source resistance (Digital Output ON)| 400| 600| mQ
DIGITAL INPUT
Input resistance (DINT)| 47| kQ
Input resistance (DIN2)| 38.45| kQ
VALUE| MIN.| TP| MAXO| IT
Input resistance (DIN3)| 150| kQ
                Input voltage(RecommendedOperating Conditions)| 0| Supplyvoltage| V
Input Voltage threshold| 75| v
Input Voltage threshold| 25| v
Input Voltage threshold (DIN3)| 25| v
OUTPUT SUPPLY VOLTAGE 1-WIRE
Supply voltage| +4.5| +47| V
Output inner resistance| 7| Q
Output current (Uout >3.0V)| 30| mA
Short circuit current (Uout=0)| 75| mA
NEGATIVE INPUT
Input resistance| 3845| kQ
Input voltage (Recommended Operating Conditions)| 0| Supplyvoltage| v
VALUE| MIN| TP| MAX.| UNT
Input voltage threshold| 0.5| v
CANINTERFACE
Internal terminal resistors CAN bus (no internal termination resistors)| Ω
Differential input resistance| 19| 30| 52| K Ω
                Recessive output| 2| 2.5| 3| V
Common mode input voltage| -30| 30| V

SAFETY INFORMATION

This message contains information on how to operate FMC250 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

• The device uses SELV limited power source. The nominal voltage is +12V DC. The allowed voltage range is +10..+30 vDC.
• To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
• When connecting the 2×6 connector wires to the vehicle, the appropriate jumpers of the vehicle power supply should be disconnected.
• Before unmounting the device from the vehicle, the 2«6 connector must be disconnected. The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. Al related devices must meet the requirements of EN 62368-1 standard. The device FMC250is not designed as a navigational device for boats.

Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.

All wireless data transferring devices produce interference that may affect other devices which are placed nearby.

The device must be connected only by qualified personnel.

The device must be firmly fastened in a predefined location.

The programming must be performed using a PC with autonomic power supply.

Installation and/or handling during a lightning storm is prohibited.

The device is susceptible to water and humidity if the device housing is not properly closed

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

Battery should not be disposed of with general household waste. Bring damaged or wom-out batteries to your local recycling center or dispose them to battery recycle bin found in stores.

CERTIFICATION AND APPROVALS

This sign on the package means that it is necessary to read the User’s Manual before your start using the device. Full User’s Manual version can be found in our Wiki¹.

1. wiki.teltonika-gps.com/index.php?title=FMC250

Hereby, Teltonika declare under our sole responsiility that the above described product is in conformity with the relevant Community harmonization: European Directive 2014/53/EU (RED).

UK Conformity Assessed (UKCA) marking is a conformity mark that indicates conformity with the applicable requirements for above described products sold within Great Britain.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by UAB Teltonika Telematics is under license. Other trademarks and trade names are those of their respective owners.
CHECK ALL CERTIFICATES
All newest certificates may be found in our WikiZ.

2. wiki.teltonika-gps.com/view/FMC250Certification%26_Approvals
   
   This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.
   
   The RoHS1 is a directive regulating the manufacture, import and distribution of Electronics and Electrical Equipment (EEE) within the EU, which bans from use 10 different hazardous materials (to date).

EMark and e-Mark are the European conformity marks issued by the transport sector, indicating that the products comply with relevant laws and regulations or directives. Vehicles and related products need to go through the E-Mark certification process to be legally sold in Europe.

WARRANTY

We guarantee our products 24-morth warranty’ period.
All batteries carry a 6-month warranty period.
Post warranty repair service for products is not provided.
If a product stops operating within this specific warranty time, the product can be:

• Repaired
• Replaced with a new product
• Replaced with an equivalent repaired product fulfilling the same functionality
• Replaced with a different product fulfilling the same functionality in case of EOL for the original product
  1. Additional agreement for an extended warranty period can be agreed upon separately.

WARRANTY DISCLAIMER

• Customers are only allowed to return products as a result of the product being defective, due to order assembly or manufacturing fautt.
• Products are intended to be used by personnel with training and experience.
• Warranty does not cover defects or malfunctions caused by accidents, misuse, abuse, catastrophes, improper maintenance or inadequate installation – not following operating instructions (including failure to heed warnings) or use with equipment with which it is not intended to be used.
• Warranty does not apply to any consequential damages.
• Warrantyis not applicable for supplementary product equipment (i. e. PSU, power cables, antennas) unless the accessory is defective on arrival.
• More information on what is RMA!

1. wiki.teltonika-gps.com/view/RMA_guidelines

References

• Download .NET Framework 4.6.2 | Free official downloads

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>