AVIANCE Lighting HD52109 Ainsworth 12.5 Inch 1-Light Brushed Nickel Outdoor Hardwired Wall Lantern Installation Guide
- July 3, 2024
- AViANCE lighting
Table of Contents
AVIANCE Lighting HD52109 Ainsworth 12.5 Inch 1-Light Brushed Nickel
Outdoor Hardwired Wall Lantern
Product Specifications
- Model : HD52109
- Brand : AVIANCE
- Power Source : Electric
- Material : Not specified
- Colour : Not specified
Product Usage Instructions
Assembling the Fixture
- Shut off the power at the circuit breaker.
- Remove the old fixture, including the single bar.
- Unpack the new fixture and lay out all parts carefully in a clear area.
- Attach the mounting screw partway into the side hole of the crook cross bar, then secure it with a hex nut.
- Attach the crossbar to the junction box using two box screws with the side marked GND facing out.
Connecting the Wires
- Connect the electrical wires:
- Black wire from the fixture to the black house (hot) wire.
- White wire from the fixture to the white (neutral) house wire.
- If there are ground wires in the outlet box, connect the fixture’s ground wire to it. Otherwise, attach the bare copper fixture wire to the green ground screw on the mounting plate.
- Secure all wire connections with wire nuts and optionally wrap them with electrical tape.
- Tuck the wire connections neatly into the wall junction box.
Final Steps
Your installation is now complete. Return power to the junction box and test
the fixture.
The drawing shown may not exactly match the product enclosed. However, the installation instructions do apply to this product.
- WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
- ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
-
Shut off the power at the circuit breaker and remove old fixture, including the single bar. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
-
Attach the mounting screw part way into the side hole of the crook cross bar, then lock it securely with hex nut until becoming. Attach the cross bar to the junction box using two box screws. The side of the cross bar marked “GND” must face out.
-
Follow wiring instructions carefully (see fig.2).
-
Using the end of arm(A) hook the lamp body’s loop, aligning the end hole of arm(A) with the top hole of back plate, lock it securely with screw(E) and hex nut.
-
Attach the back plate of the lamp body(B) onto the junction box, aligning screws on crossbar with mounting holes and lock it securely with the ball nuts(C).
-
Install the light bulbs(Not included) in accordance with the fixture’s specifications.
NOTE : DO NOT EXCEED THE MAXIMUM WATTAGE RATING! -
With silicone caulking compound, caulk completely around where back of cover meets with the wall surface to prevent water from seeping into junction box.
CONNECTING THE WIRES (Fig.2)
- Connect the electrical wires as follows. Connect the Black wire from the fixture to the black house (hot) Wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet box has a ground wires (green or bare copper) connect fixture’s ground wire to it. Otherwise attach the bare copper fixture wire to the green ground screw on the mounting plate.
- Tuck the wire connections neatly into the wall junction box.
Your installation is now complete. Return power to the junction box and test the fixture.
Thank you for purchasing an AVIANCE product.
Need assistance with parts or assembly?
Please email customer service
at:info@aviancelighting.net
©COPYRIGHT ALL RIGHTS RESERVED. AVIANCE LIGHTING,INC.
FAQ
Q: What should I do if I encounter any issues during installation?
A: If you encounter any difficulties during installation or have any
questions, please contact customer service at
info@aviancelighting.net for assistance.
Thank you for choosing AVIANCE products.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>