AVIANCE lighting HD81161 Fixture 1-Light Brushed Nickel LED Lantern Instruction Manual
- July 4, 2024
- AViANCE lighting
Table of Contents
AVIANCE lighting HD81161 Fixture 1-Light Brushed Nickel LED Lantern
Product Specifications
- Model: HD81161
- Brand: AVIANCE
- Fixture Type: Ceiling Light Fixture
- Power Source: Electric
- Color: White
- Material: Metal and Glass
Product Usage Instructions
Assembling & Installation
The drawing shown may not exactly match the product enclosed. However, the
installation instructions do apply to this product.
WARNING!
SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER. ATTENTION! COUPER LE COURANT AU
FUSIBLE OU UN DISJONCTEUR.
Assembling the Fixture:
- Shut off the power at the circuit breaker box.
- Remove the old fixture.
Connecting the Wires
- Connect the electrical wires as follows:
- Connect the Black wire from the fixture to the black house (hot) wire.
- Connect the white wire from the fixture to the white (neutral) house wire.
- Make sure all wire nuts are secured. You may wrap the connections with electrical tape.
- If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, attach the bare copper fixture wire to the green ground screw on the mounting plate.
- Tuck the wire connections neatly into the wall junction box.
FAQ (Frequently Asked Questions)
-
Q: What should I do if I encounter flickering lights after installation?
A: Flickering lights can be caused by loose connections. Double-check all wire connections and ensure they are tightly secured with wire nuts and electrical tape -
Q: Can this fixture be used in a bathroom?
A: It is recommended to check the product specifications and ensure that the fixture is suitable for damp or wet locationsbefore installing it in a bathroom.
ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed. However, the
installation instructions do apply to this product.
HD81161
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
- Shut off the power at the circuit breaker box. Remove old fixture and all hardware from Junction Box. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
- Thread the pipe screw part way into the center hole of the single bar and secure with hex nut. Attach the single bar to the junction box using two box screws. The side of the single bar marked “GND” must face out. The junction box is not included.
- Follow wiring instructions carefully(see fig.2).
- Attach the lamp body onto the junction box, aligning screws on single bar with mounting hole, lock it securely with the ball nut.
- Install the light bulb(not included) in accordance with the fixture’s specifications. NOTE: DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
- With silicone caulking compound, caulk completely around where back of cover meets with the wall surface to prevent water from seeping into outlet box.
CONNECTING THE WIRES (Fig.2)
- Connect the electrical wires as follows. Connect the Black wire from the fixture to the black house (hot) Wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet box has a ground wires (green or bare copper) connect fixture’s ground wire to it. Otherwise attach the bare copper fixture wire to the green ground screw on the mounting plate.
- Tuck the wire connections neatly into the wall junction box.
Your installation is now complete. Return power to the junction box the fixture.
Thank you for purchasing an AVIANCE product.
Need assistance with parts or assembly? Please email customer service at:
info@aviancelighting.net
©COPYRIGHT ALL RIGHTS RESERVED. AVIANCE LIGHTING,INC.
DOC202404HD81161
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>