AVIANCE lighting HD56435 Wessex 9.5 Inch 1 Light Antique Brass Outdoor Hardwired Wall Lantern Instruction Manual
- July 3, 2024
- AViANCE lighting
Table of Contents
AVIANCE lighting HD56435 Wessex 9.5 Inch 1 Light Antique Brass Outdoor
Hardwired Wall Lantern
Product Specifications
- Model: HD56435
- Brand: AVIANCE
- Power Source: Electric
- Color: Not specified
- Material: Not specified
Product Usage Instructions
Assembling & Installation Instructions:
The drawing shown may not exactly match the product enclosed. However, the
installation instructions do apply to this product.
Assembling the Fixture (Fig.1):
- Shut off the power at the circuit breaker box.
- Remove the old fixture.
Connecting the Wires (Fig.2):
-
Connect the electrical wires as follows:
- Connect the Black wire from the fixture to the black house (hot) Wire.
- Connect the white wire from the fixture to the white (neutral) house wire.
- Make sure all wire nuts are secured. You may wrap the connections with electrical tape.
- If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, attach the bare copper fixture wire to the green ground screw on the mounting
plate.
-
Tuck the wire connections neatly into the wall junction box.
Your installation is now complete. Return power to the junction box.
Thank you for purchasing an AVIANCE product.
Need assistance with parts or assembly? Please email customer service at:
info@aviancelighting.net DOC202404HD56435
Frequently Asked Questions (FAQ):
-
Q: Can this product be used outdoors?
A: The product is designed for indoor use only and should not be exposed to outdoor elements. -
Q: Is this product dimmable?
A: Refer to the product specifications or contact customer service to check if the product is dimmable.
ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed. However, the
installation instructions do apply to this product.
HD56435
- WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
- ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE
-
Shut off the power at the circuit breaker box. Remove old fixture and all hardware from Junction Box. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
-
Thread the pipe screw part way into the center hole of the single bar and secure with hex nut. Attach the single bar to the junction box using two box screws. The side of the single bar marked “GND” must face out. The junction box is not included.
-
Follow wiring instructions carefully(see fig.2).
-
Attach the lamp body onto the junction box, aligning screws on single bar with mounting holes and lock it securely with the ball nut. Put the candle sleeve over the lamp holder.
-
Install the light bulbs(not included) in accordance with the fixture’s specifications.
NOTE : DO NOT EXCEED THE MAXIMUM WATTAGE RATING! -
With silicone caulking compound, caulk completely around where back of cover meets with the wall surface to prevent water from seeping into outlet box.
CONNECTING THE WIRES
- Connect the electrical wires as follows. Connect the Black wire from the fixture to the black house (hot) Wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet box has a ground wires (green or bare copper) connect fixture’s ground wire to it. Otherwise attach the bare copper fixture wire to the green ground screw on the mounting plate.
- Tuck the wire connections neatly into the wall junction box.
Your installation is now complete. Return power to the junction box and test the fixture.
Thank you for purchasing an AVIANCE product.
Need assistance with parts or assembly? Please email customer service
at:info@aviancelighting.net
©COPYRIGHT ALL RIGHTS RESERVED. AVIANCE LIGHTING,INC.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>