PELONIS PHO25A4ABWUK Oil Filled Radiator User Manual
- July 5, 2024
- Pelonis
Table of Contents
PELONIS PHO25A4ABWUK Oil-Filled Radiator
Specifications :
- Power Supply : 220-240V~, 50Hz
- Power Output: 2500W
- Heat Output : 1.1 kW
- Heat Charge Control: Manual with integrated thermostat
- Minimum Heat Output: 1.0 kW
- Maximum Continuous Heat Output: 1.1 kW
- Auxiliary Electricity Consumption: 0.000 kW (at nominal heat output)
- Type of Heat Output/Room Temperature Control: Electronic room temperature control
Product Usage Instructions
Installation Instructions:
- Turn the heater body upside down with the bottom facing up.
- Align the mounting buckles of the foot components with the holes of the heat sink and press in the direction of the arrow to secure them.
- Align the mounting groove of the foot with the one-way wheel and clamp on the second heat sink, then align the other foot mounting slot with the penultimate heat sink. Ensure a firm installation before use.
LED Display Function:
- Display Window: Shows relevant information.
- Button Function Description:
- Press the key in the standby state to power on.
- Press the key in the power-on state to enter standby mode.
Operating Instructions:
- Check the requirements and safety grounding before use.
- Select power levels by cycling through high-grade, mid-grade, low-grade, and high-grade.
- Adjust the temperature as needed.
- Use the stop key to switch between power-on and standby states.
Cleaning and Maintenance:
Follow proper precautions for cleaning and maintenance as per user manual instructions.
Disposal and Recycling:
Dispose of the product responsibly following local regulations for recycling and disposal.
FAQ
- Q: Can this product be used continuously in a poorly insulated space?
- A: No, this product is only suitable for well-insulated spaces or occasional use as mentioned in the user manual.
- Q: How do I adjust the heat output?
- A: You can adjust the heat output by selecting different power levels using the control panel.
This product is only suitable for well-insulated spaces or occasional use. Attention: Pictures in the IM are for reference only
SAVE THESE INSTRUCTIONS
CAUTION
-
Read Rules for Safe Operation and Instructions Carefully.
-
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance. -
CAUTION — Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
WARNING
Warning: In order to avoid overheating, do not cover the heater.
- If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
- The heater must not be located immediately below a socket outlet.
- Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
- This heater is filled with a precise quantity of special oil.
- Repairs requiring the opening of oil container are only to be made by the manufacturer or his service agent who should be contacted if there is an oil leak. When scrapping the heater, follow the regulations concerning the disposal of oil.
- This heater cannot achieve accurate temperature control of the environment, and thus cannot be used as an insulation device for storage environment, items, animals, and plants.
- Do not use this heater if it has been dropped.
- Do not use if there are visible signs of damage to the heater.
- Use this heater on a horizontal and stable surface, or fix it to the wall, as applicable.
- WARNING: Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own unless constant supervision is provided.
- WARNING: To reduce the risk of fire, keep textiles, curtains, or any other flammable material a minimum distance of 1 m from the air outlet.
- Do not use outdoors.
PART FIGURE
INSTALLATION INSTRUCTIONS
- Turn the heater body upside down with the bottom facing up.
- As shown in Figure 1, align the mounting buckles of a set of foot components. The hole of the heat sink, press in the direction of the arrow, the buckle on the foot. Just drop into the hole of the heat sink.
- As shown in Figure 2, align the mounting groove of the foot with the one-way wheel and Clamp on the second heat sink, the other foot mounting slot is aligned. It is stuck on the penultimate heat sink. Install it firmly before heating. Place the device upright and the wheels can be on the ground
LED DISPLAY FUNCTION
OPERATING INSTRUCTIONS
Inspection before start
- The power cord shall not be damaged or fractured.
- Please verify the rated current of the power socket is in line with the requirements in the table above and is equipped with a safety grounding device before use; otherwise, replace the socket.
Start and power selection
Start
- Press the “ ” key in the standby state to enter the power-on state.
Power selection
- When the machine is running, press the “ ” key repeatedly, and the machine will switch in the cyclic sequence of “high-grade mid-grade low-grade high-grade”.
[Note]
- To use the machine for the first time or to re-insert the socket, please pay attention to checking whether the plug and the socket are fitted well.
**< Inspection method>**
- Insert the power plug into the socket and start for use; after about half an hour, turn off and pull out the plug. Check whether the plug pins are hot; replace the socket if so (more than about 50°C) to avoid burning the plug or even causing a fire caused by overheating of the socket due to poor contact.
Temperature adjustment
- In the power-on state, short press the “ ” key to enter the temperature setting state, and press the key repeatedly to switch in the cyclic order of “18, 22, 26, 30, 35”. Long press the ” ” button, the temperature will increase continuously and rapidly (range 5-35°C). If there is no key action within 5 seconds, confirm the temperature setting value.
Stop
- Press the “ ” key in the power-on state to enter the standby state.
Movement of the heater
- To move the heater, turn it off first, and pull out the power plug; then push the body to make the four casters below the body to roll.
CLEANING AND MAINTENANCE
Precautions
- The electric heater should be cleaned regularly to wipe out the dust on the surface of the flanges. As this may influence the radiating efficiency.
- Disconnect the electricity supply and allow the radiator to cool, wipe out dust with a soft damp cloth. Do not use detergent or abrasives.
- Do not scrap the surfaces of flanges with sharp hard tools, to avoid surfaces getting rusty, because of damage of the paint coat.
DISPOSAL AND RECYCLING
This product complies with EU WEEE Directive and bears a classification symbol for waster electrical and electronic equipment (WEEE).
SPECIFICATIONS
This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the dealer where the product was purchased. They can take this product for environmentally safe recycling.
SERVICE AND SUPPORT
In the event of a warranty claim or if service is required for this product, please contact us at the following:
E-mail : cs_eu@pelonis.com
| Item | Symbol | Value | Unit | Item | Unit |
|---|
Heat output
| Type of heat input, for electric local space heaters only (select one)
Nominal heat output|
Pnom
|
1.1
|
kW
| Manual heat charge control with integrated thermostat| [no]
Minimum heat output (indicative)
|
Pmin
|
1.0
|
kW
| Manual heat charge control with room and/or outdoor temperature feedback|
[no]
Maximum continuous heat output|
Pmax
|
1.1
|
kW
| Electronic heat charge control with room and/or outdoor temperature
feedback| [no]
Auxiliary electricity consumption| Fan-assisted heat output| [no]
At nominal heat output|
elmax
|
0.000
|
kW
| Type of heat output/room temperature control (select one)
At minimum heat output|
elmin
|
0.000
|
kW
| Single stage heat output and no room temperature control| [no]
In standby mode
|
elSB
|
0.254
|
W
|
Two or more manual stages, no room temperature control
| [no]
| | | | With mechanic thermostat room temperature control| [no]
| | | | With electronic room temperature control| [yes]
| | | | Electronic room temperature control plus day timer| [no]
| | | | Electronic room temperature control plus week timer| [no]
| | | | Other control options (multiple selections possible)
| | | | Room temperature control, with presence detection| [no]
| | | | Room temperature control, with open window detection| [no]
| | | | With distance control option| [no]
| | | | With adaptive start control| [no]
Item| Symbol| Value| Unit| Item| Unit
---|---|---|---|---|---
| | | | With working time limitation| [yes]
| | | | With black bulb sensor| [no]
Contact details|
Lifestyle Orchestra Co. Pte. Ltd.
158 CECIL STREET#07-01/02 SINGAPORE (069545)
Company TC Kangbridge Ltd
- Address: TC Luminous house,300South row,Milton Keynes,MK9 2FR
- Tel/Mobile: +44(0)7908917780
- E-mail:epr@tangcheng.top
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>