Surge Toy Gel Blasters with Water Based Beads Instruction Manual
- June 1, 2024
- GEL BLASTER
Table of Contents
Toy Gel Blasters with Water Based Beads
STEP 1 – CHARGE YOUR BLASTER
Use the provided USB-C cord to charge your blaster. Do not place your charging
blaster on any fabric surface during charging. Do not leave blaster charging
for an extended period of time, unplug it when the indicator light turns
green.
STEP 2 – FILL YOUR HOPPER
Fill your hopper with hydrated Gellets® – make sure all water is drained from
the hopper before installing on your blaster. Discard any unused hydrated
Gellets after play.
STEP 3 – INSTALL HOPPER ONTO BLASTER
Screw the full hopper into the blaster feedneck, then flip your blaster upside
down to slide the feedneck onto the top rail of the blaster with the arrow
pointing forward.
IMPORTANT – Make sure you slide the feedneck all the way forward until
you feel and hear a “click”. Failing to do so will cause your blaster to
misfire.
STEP 4 – OPTIONAL: INTERCHANGEABLE BARRELS
Your blaster currently comes with the Standard Barrel pre-installed. To remove
the barrel, use the Barrel Tool provided to unscrew the barrel. You can then
install your orange Reduced Velocity Barrel for a lighter blasting experience.
STEP 6 – PROTECT YOUR EYES!
Wear the provided eye protection when using your blaster. Do not blast at
people unless they’re using proper eye protection.
STEP 7 – POWER ON AND HAVE A BLAST!
Switch between Single and Full-Auto with the Blaster Mode Switch.
Your blaster is not intended to get wet. Don’t submerge your Gel Blaster®
product in water, and make sure your Gellets® are fully strained of excess
water. This will protect the internals within from failure.
ONE GALLON OF WATER MAKES 10,000 GELLETS™! 
IMPORTANT SAFETY INFORMATION
Retain these instructions for important safety information
WARNING| Do not brandish or display this product in public – It may
confuse people and may be a crime. Police and others may think it is a real
firearm. Do not change the coloration and the markings to make it more like a
firearm. That is dangerous and may be a crime.
---|---
WARNING| NOT A TOY. ADULT SUPERVISION REQUIRED. MISUSE OR CARELESS USE
MAY CAUSE SERIOUS INJURY, PARTICULARLY TO THE EYE. MAY BE DANGEROUS UP TO 49
YARDS (45 METRES).
WARNING| Keep Gellets® away from children. Do not ingest Gellets®. Do
not freeze Gellets®. Do not eat. Do not modify Gellets®.
Always follow directions when making Gellets®. Do not aim at eyes or face
during play. Use only with Gel Blaster® Official Products.
IMPORTANT BATTERY INFORMATION
The battery charger used with the electric product shall be regularly examined
for damage to the supply cord, plug, enclosure or other parts, and in the
event of damage, it shall not be used until the damage has been repaired. The
product shall only be used with a transformer or a power supply compatible
with the product.
Power supply is not a toy.
- Uses rechargeable non-replaceable lithium-ion battery-included
- Batteries are rechargeable
- Batteries are non-accessible and non-replaceable
- Do not alter the blaster battery
- For the purposes or recharging the battery, only use the detachable supply unit provided with this product
** Your blaster provides hours of playtime per charge using a powerful lithium
ion battery! But with that power comes the responsibility to take care of your
battery.
Abuse, neglect, or misuse can ruin your battery, shorten your playtime, or
cause the battery to overheat. If your blaster won’t take a charge, unplug
immediately and contact
support@gelblaster.com
FAQ & QUICK FIXES
Q: My Hopper & Feedneck keeps sliding off and won’t feed the Gellets® into
my blaster. Is it broken?
A: No, you didn’t break it. Just make sure your hopper is facing the right
direction – the front arrow (on your feedneck) should be facing toward your
fins. If installed correctly, the hopper and feedneck will click & lock in
place. If all else fails, reread this section and then proceed to scream
internally and reassemble until success.
Q: My Gellets® aren’t shooting correctly and are rolling out of my
blaster’s barrel. Help?
A: No worries buddy. Your Gellets aren’t fully hydrated yet (they are too
small) and they just need more time to be submerged in water. To make sure
your Gellets are fully hydrated, please allow your Gellets to be submerged in
water for a minimum of two hours before playing.
WATCH QUICK TIPS
LIMITED WARRANTY, SUBROGATION WAIVER, WAIVER AND RELEASE, BINDING
AGREEMENT
TO ARBITRATE, CLASS ACTION WAIVER
Gel Blaster, Inc. warrants this Gel Blaster® product for a period of three
months from the date of consumer purchase to be free from defects in material
and workmanship. Gel Blaster, Inc.’s obligation under this warranty is limited
to repair or replacement of the purchased product only (although Gel Blaster,
Inc may determine to issue a refund, in its sole and exclusive discretion),
and under no circumstances shall Gel Blaster, Inc. be liable for any loss,
damage, injury, cost of repair, consequential damages, incidental damages, or
punitive, treble, or exemplary damages of any kind in connection with the
sale, use, failure, or repair of any product purchased from or produced by Gel
Blaster, Inc, even if such damages are caused by the negligence of the
released party, whether sole or in combination with others. You hereby waive
any claim by an insurance carrier or other person or entity by way of
subrogation, and you hereby assign any and all such subrogation claims to Gel
Blaster, Inc.
Gel Blaster, Inc. disclaims any warranty of fitness for a particular purpose
and any implied warranty of merchantability. All implied warranties are hereby
disclaimed, and you agree that the only warranty provided by Gel Blaster, Inc.
to you is the above.
Gel Blaster, Inc.’s liability for any and all claims arising out of or
connected with the Gel Blaster® shall be limited to the amount paid by
consumer for the product plus the sum of $100.00.
You and Gel Blaster, Inc. agree to mandatory, binding arbitration for any and
all claims or causes of action between the parties arising out of or in
connection with your purchase or use of the Gel Blaster®, its accessories, or
otherwise with respect to any claims between you and Gel Blaster, Inc. The
arbitration shall take place under the rules of the American Arbitration
Association, Consumer Arbitration Rules, before a single arbitrator. The
Arbitration shall take place in Dallas, Texas. You understand and agree that
you are waiving your rights to a trial by jury. You agree that any claim you
have or may ever come to have against Gel Blaster, Inc.
must be submitted on an individual basis, and you hereby waive the right to
assert such claim collectively, such as in a class or mass action. As a
condition precedent to filing arbitration, you must contact Gel Blaster, Inc.
with any claim or dispute, which must be mediated before a mutually agreeable
mediator in Dallas, Dallas County, Texas.
You agree to the foregoing terms when you first charge, add batteries, or
otherwise seek to use your Gel Blaster® product or its accessories.
WARNING: Changes or modiications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Cass B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that intererence will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/ TV technician for help.
www.gelblaster.com
Gel Blaster, Inc. Austin, TX 78746
Designed in Austin, TX
Made in China
©2023 Gel Blaster, Inc.
All Rights Reserved
www.gelblaster.com/patents
Documents / Resources
| Gel
Blaster Surge Toy Gel Blasters with Water Based
Beads
[pdf] Instruction Manual
Surge Toy Gel Blasters with Water Based Beads, Surge, Toy Gel Blasters with
Water Based Beads, Blasters with Water Based Beads, Water Based Beads, Based
Beads, Beads
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>