PELONIS HO-0280 Digital Oil-Filled Radiator Heater User Manual

PELONIS HO-0280 Digital Oil-Filled Radiator Heater

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear.
3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater or return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
6. Do not use outdoors.
7. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into bathtub or other water container.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
9. To disconnect heater, first turn controls to off, then remove plug from outlet.
10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside. Do not use it in the areas where gasoline, paint, or flammable liquids are used or stored.
13. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
14. Caution Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
15. This heater draws 12.5 amps during operation. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances working.
16. It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle) and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace loose or worn outlet.
17. The output of this heater may vary and its temperature may become intense enough to burn exposed skin. Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to react to avoid burns.
18. Don’t leave the heater on unattended.

SAVE THESE INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

Unpack your heater and find the wheel-holding plate and butterfly nuts between the fins assemblies.

1. Make sure the heater is unplugged and in the “OFF” position.
2. TURN THE HEATER UPSIDE DOWN.
3. Attach the wheel-holding plates onto the heater as Fig.1 shows. The plate is fixed between the last two fins and the other one is fixed under metal control box, Fix the castors to the vertical axis of both the wheel holding plates.
4. Insert the butterfly nuts and tighten them securely.
5. TURN THE HEATER UPRIGHT. Your heater is now ready to use.

Warning

Risk of fire. Do not operate heater without wheel assemblies attached. Operate heater in upright position only (wheels on bottom, controls on top). Any other position could create a hazardous situation. Ensure that the surface beneath the heater is clean and free of any obstructions. It is not recommended that this heater be placed on high-pile carpeting or any other surface that impedes the flow of air underneath the heater.

Caution

This heater includes an Overheat Protection System that shuts the unit off if it overheats due to abnormal conditions. If this occurs turn the heater “OFF”, unplug it, and inspect and remove any objects on or adjacent to the heater. Allow it to cool for a few minutes, plug it back in, and resume normal operation.

OPERATING INSTRUCTION

How to use [Inspection before startup].

1. Check the power cord for any damage;

2. Prior to use, please confirm that the power socket has acceptable rated current, and if not, please replace it.
   [Operation instructions] <on/off >: By power on, the buzzer will give a long sound of “beep”. Press the on-off key to start up and enter the high-grade heating, and then press the on-off key to shut down. : Gently press the gear selection key “MODE” under the working state to select any one of high-grade, middle-grade, low-grade and energy-saving work modes.

   : Under the working state, press and hold the “∧” key or “∨” key to set the temperature, with the temperature setting step of 1; long press the “∧” key or “∨” key to set the temperature quickly. After temperature setting, exit the temperature setting interface in case of no operation for 5 seconds. In the event of first use or self-inspection for memory information clearing, the machine will operate after start according to the factory settings, and the high temperature setting default is 95°F. : Press the timing key “ ” in standby mode to enter the start setting interface. Press the “∧” key or “∨” key to set time for startup. Long press “∧” key or “∨” key to quickly set time for startup. Upon the time set, the machine will start and the buzzer will make a long sound. : Press the timing key “ ” in startup mode to enter the shutdown setting interface. Press the “∧” key or “∨” key to set time for shutdown. Long press “∧” key or “∨” key to quickly set time for shutdown. Upon the time set, the machine will shut down.

3. Timing range between 0 and 24 hours. Increase or decrease for 1 hour by pressing the “∧” key or “∨” key each time. When the setting value is 0H, press the “∨” key to change the setting time to 24H. When the setting value is 24H, press the “∧” key to change the setting time to 0H. When the setting value is 0H, cancel the timing; when the setting value is not 0H, start the timing. After the time is set, press the “ ” key or “MODE” key, or in case of no operation for 5 seconds, exit the timing MODE.

4. If the time is set, press the “ ” key to shut down and cancel the timing.

5. After timing, press the “ ” key to check the remaining time and reset the time at any time. During the timing period, the machine can be stopped or restarted under the temperature control state, and the timing will be kept normally, and not affected by such stop and restart. In case of closedown or power off during the timing period, the timer will reset to zero. : Under no child lock state during startup and standby, press and hold the “ ” key and the “MODE” key for 3 seconds at the same time to start the child lock function. Under child lock state during startup and standby, press and hold the “ ” key and the “MODE” key for 3 seconds to turn off the child lock function.

Note:

1. When the child lock is in effect during startup, all operations other than shutdown invalid (except release of the child lock); the child lock is canceled after shutdown.
2. When the child lock is in effect during standby, all operations are invalid (except release of the child lock). : If the machine is restarted after normal shutdown, it will run at the latest state before shutdown. If the machine is powered on again after power off, it will also run at the latest state before power off. Note: The memory function is not applicable to child lock after power off. : If the indoor environment temperature Th exceeds 122°F during standby or startup time, please close all output, the buzzer will give ten acute sounds, and the digital display will show “FF” and flash for 75 seconds with the frequency of 1HZ. If the protection function works, the machine cannot resume running or operation, though the environment temperature is less than 122°F. In this case, it is necessary to power off and then power on the machine for operation. : When the machine is turned on, press the “ ” key on the control panel to enter the standby state. Unplug the power cord, and then place the electric heater well after the machine is cooled.
   [Electric heater movement] To move the electric heater, please turn it off, unplug the power cord, and then push the heater body to make the following four universal casters to scroll. Note: In the event of first use or re- inserting the power plug into socket, please check the compatibility of the plug and socket. Inspection method: Insert the power plug into socket and turn the machine on. About half an hour later, shut the machine down and disconnect plug to check whether the plug pin is hot. If the pin is hot (about more than 122°F), the socket must be replaced to avoid socket overheating and even fire caused by poor contact.

INSTRUCTIONS TO REMOTE CONTROLLER

BATTERIES INSTRUCTIONS (included)

1. Press down on the battery compartment cover and slide it out.
2. Use 1 “CR2032” lithium battery (included)
3. Insert the batteries, making sure that the positive terminals are facing the proper way.
4. Replace the cover.

BATTERY WARNING

1. Do not dispose of batteries in fire, batteries may explode or leak.
2. Do not mix old and new batteries.
3. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
4. Non-rechargeable batteries are not to be recharged.
5. Batteries are to be inserted with the correct polarity.
6. Exhausted batteries are to be removed from the product.
7. The batteries must be removed from the remote controller before it is scrapped and that they are disposed of safely.

SAFTEY FEATURES

The heater is equipped with an over-heat device which cause the unit to stop operating in the event that the internal temperature exceeds the normal operating temperature.

If the heater shuts down

1. Turn off and unplug the heater.
2. Wait for at least 10 minutes until the heater cools.
3. Plug the heater into the power outlet and then turn it on.
   Note: This heater includes a safety tip-over protection feature which will shut the heater off in case it is tipped over. If, at any time, the heater does tip over, please put the heater back in the upright position (wheels on bottom, controls on top). The heater will resume its normal operation.

CARE AND CLEANING

1. Always remove the plug from the power socket and allow heater to cool. Wipe heater with a soft, damp cloth. Do not use detergents and abrasives.
2. If the heater is not in use over a certain length of time, wind the cable around the holder and store it in a dry place.
3. In case of malfunction, do not try to repair the heater by yourself. It may result in fire hazard or electric shock.

SPECIFICATIONS

120 V AC

| ****

60 Hz

| ****

1500 W

| ****

12.5 A

| ****

5120

This heater is designed for finite space heating or as a supplementary heating source. It can not replace the main heat source during the winter.

TROUBLESHOOTING

Your heater shuts off unexpectedly or fails to operate.

| 1. There is no power.| Be sure it is plugged in and that the electrical outlet is working.
2. The set temperature is lower than the current room temperature.| Set the desired temperature higher than the current temperature to restart the heater.

3. The room temperature has reached the temperature set at the thermostat.

| 1. This is normal. The heater will restart once room temperature is lower than set temperature.

2. Adjust the thermostat setting if it’s not set to your desired temperature.

4. One of the safety protection devices had been activated to prevent overheating.

| 1. Place the heater in upright position.

2. Check for any obstructions. If you find an obstruction, turn the heater off.

3. Unplug the heater and wait at least 10 minutes for it to cool down.

4. Carefully remove the obstruction. Plug the heater in and restart it as described in the OPERATION section.

5. If you still notice the same problem, remove the plug from the outlet and have the appliance checked by an authorized service person.

The room is not hot enough.

| ****

1. The room is too large.

2. The window is open.

| 1. Turn on the main heat source of the room.

2. Use more portable heaters.

3. Close the window.

3. The set temperature is too low.

4. The power setting is too low.

| 4. Increase the temperature setting.

5. Select the higher power setting.

Caution Please do not attempt to open or repair the heater by yourself. Doing so may void the warranty and could cause damage or personal injury.

SERVICE & SUPPORT

ONE (1) YEAR LIMITED WARRANTY

Please read all instructions before attempting to use this product.

In the event of malfunctions or failure of your Pelonis Product, simply deliver or send the heater, postage prepaid along with PROOF OF PURCHASE, within the warranty period of one (1) year, to
reserves the right to inspect the claimed defective part or parts to determine if the defect or malfunction complaint is covered by this warranty. shall, within sixty (60) days after receipt of the product, at its option,repair and/or replace the defective part or parts free of charge. This warranty shall only cover defects arising from normal usage. assumes no responsibility whatsoever if Product should fail during the warranty period by reason of:

• Misuse, negligence, physical damage or accidents.
• Lack of maintenance (see instructions for proper maintenance).
• Repair by any unauthorized party during the warranty period.
• Damage caused by connection to an improper input voltage (see specification label on your heater).

PELONIS makes no further warranties or representations, express or implied except those contained herein. No representative or dealer is authorized to assume any other liability regarding the Product. The duration of the implied warranty granted under State law, including warranties of merchantability and fitness for particular purpose are limited in duration should the duration of the express warranty grant it hereunder.PELONIS shall in no event be liable for direct, indirect, special or consequential damages. Some states do not allow limitations on how long an implied warranty lasts, and/or the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights and you may have other rights which vary from state to state.

References

• Midea - Make yourself at Home - World's Number 1 Appliance Producer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>