JUMMICO 65×45 Standing Desk Electric Adjustable Desk Instruction Manual
- June 14, 2024
- JUMMICO
Table of Contents
JUMMICO 65x45 Standing Desk Electric Adjustable Desk Instruction Manual
Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact our online after-sale service for help.
⚠ CAUTION: Use with products heavier than the rated weights indicated may result in instability causing passible injury.
- Mounts must be attached as specified is assembly instructions, improper installation may result in damage or serious personal injury.
- Safety gear and proper tools must be used. This product should only be installed by professionals.
- Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, please contact our online after-sale service for help.
- MAINTENANCE: Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Digital Control Panel For Electric Height Adjustable Desk
Lifting Function:
Press “∧ “button, the desk will rise and stop automatically when it rises to
the highest point.
Press “∨ “button, the desk will descend and stop automatically when it
descends to the lowest point.
Release the button and the desktop stops the current action.
Preset Memory Height function:
long press the digit “1” button for 3 seconds, and “S-1” is displayed,
indicating that the current height is saved to the “1” button successfully.
The same operation to digit “2” button.
Recall Memory Height Function:
Short press the digit “1” button to recall its corresponding height and
automatically run the desktop to this height.
The same operation to digit “2” button.
Desktop Resat:
When “ER1” is displayed or the desktop is at the lower limit position, press
and hold the “∨ “button for more than 3 seconds until “RST” is displayed and
release the button. At this time, the system has entered the reset preparation
state. Press and hold the “∨”button again, the desktop begins to descend to
the bottom of the machine and rebound to a certain height. After reset, the
lowest height is displayed, and then release the “∨” button.
Child Safety lock:
Press and hold the” ∧∨ ” buttons for more than 5 seconds to set the child
safety lock. After the setting is successful, ”LOC’ will be displayed. At this
time, all key operations are invalid, but the child lock can still be
cancelled by pressing and holding the” ∧∨ “button for more than 5 seconds.
Anti-Collision Detection:
An advanced feature that helps you stop your desk from moving and reverse its
movement slightly when the desk touches something.
Overheat Protection:
“hot” is displayed. If the desktop continuously rises and descends too
frequently, desk motor will overheat. In order to avoid damage to the desk
motor, desk’s height adjustment will be disable for around 18 minutes.
Motor Abnormal Protection:
When “ER1” is displayed, please power off first, check and ensure that the
connection between the motor and the controller is reliable, then power on
again and start reset procedure.
Setup Menu:
Long press” [1][2]” button for 20 seconds, and the system enters the setup menu with 7 settings available to choose from:
- Set minimum height: The foot length within desk’s adjustment range is 1 cm, and desk’s minimum height shall be at least 10 cm shorter than its maximum height.
- Set maximum height: The foot length within desk’s adjustment range is 1 cm, and desk’s maximum height shall be at least 10 cm taller than its minimum height.
- Sensitivity setting for anti-collision protection (upward adjustment): ranging from U-0 to U-9, where U-0 represents the protection disabled and U-9 represents the maximum sensitivity.
- Sensitivity setting for anti-collision protection (downward adjustment): ranging from d-0 to d-9, where d-0 represents the protection disabled and d-9 represents the maximum sensitivity.
- Display settings (decimal point): F-0 represents the height value will not be displayed with the decimal point, while F-1 represents it will.
- Display settings (unit system): L-0 represents desk height in metric system, and l-1 represents it in imperial system with the decimal point displayed.
You may press and hold”[1][2]” shortly to switch between the 7 settings; press on”∧” or” ∨” to perform settings respectively; press and hold “[1][2]” for no less than 5 seconds until the “BBB” is displayed to have current setting saved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>