reolink Argus PT Ultra 4K PT Solar Security Camera Instruction Manual
- June 15, 2024
- reolink
Table of Contents
Operational Instruction
Apply to: Argus PT Ultra
What’s in the Box
Camera Introduction
- Lens
- IR LEDs
- Spotlight
- Daylight Sensor
- Built-in PIR Sensor
- Built-in Mic
- Status LED
- Speaker
- Reset Hole
- Press for more than five seconds to restore the device to default settings. 10. Micro SD Card Slot
- Rotate the camera’s lens to find the reset hole and the SD card slot. 11. Power Switch 12. Antenna 13. Charging Port 14. Battery Status LED
Different states of the status LED:
Red Light: WiFi connection failed Blue Light: WiFi connection succeeded
Blinking: Standby status
On: Working status
Set up the Camera
Set up the Camera Using a Smartphone
Step 1 Scan to download the Reolink App from the App Store or Google Play
store.
https://reolink.com/wp-json/reo-v2/app/download
Step 2 Turn on the power switch to power on the camera.
Step 3 Launch the Reolink App, click the “ ” button in the top right corner to
add the camera.
Scan the QR code on the device and follow the onscreen instructions to finish
initial setup.
NOTE : This device supports 2.4 GHz and 5 GHz Wi-Fi networks. It is
recommended to connect the device to 5 GHz Wi-Fi for a better network
experience.
Step 1 Download and install the Reolink Client: Go to reolink.com > Support >
App&Client.
Step 2 Launch the Reolink Client, click the “ ” button, input the UID code of
the camera to add it and follow the onscreen instructions to finish initial
setup.
Set up the Camera on PC (Optional)
Charge the Camera
It’s recommend to fully charge the battery before mounting the camera.
Charge the battery with a power adapter(not included)
Charge the battery with the Reolink Solar Panel (Not included if you only
purchase the camera).
Charging Indicator:
- Orange LED: Charing
- Green LED: Fully charged
For better weatherproof performance, please always cover the USB charging port with the rubber plug after charging the battery.
Install the Camera
- The camera MUST be installed upside down for better waterproof performance and better PIR motion sensor’s efficiency.
- Install the camera 2-3 meters (7-10 ft) above the ground. This height maximizes the detection range of the PIR motion sensor.
- For better motion detection performance, please install the camera angularly.
NOTE : If a moving object approaches the PIR sensor vertically, the camera may fail to detect motion.
Mount the Camera
Drill holes in
accordance with the mounting hole template and screw the camera bracket to the
wall.
Install the antenna to the camera.
NOTE : Use the drywall anchors included in the package if needed.
Align the white hole on the camera top with the white hollow screw on the bracket. Use a wrench and a hex head screw provided to secure the camera into place. Then cover the rubber plug.
Mount the Camera to Ceiling
Install the mount
base to the ceiling. Align the camera with the bracket and turn the camera
unit clockwise to lock it in position.
Install the Camera with Loop Strap
You are allowed to strap the camera to a tree with both the security mount and
ceiling bracket.
Thread the provided strap to the plate and fasten it to a tree. Next, attach
the camera to the plate and you are good to go.
Safety Instructions of Battery Usage
The camera is not designed for running 24/7 at full capacity or around-the-
clock live streaming.
It’s designed to record motion events and to live view remotely only when you
need it.
- The battery is built-in, so do not remove it from the camera.
- Charge the rechargeable battery with a standard and high-quality DC 5V/9V battery charger or Reolink solar panel. Do not charge the battery with solar panels from any other brands.
- Charge the battery when temperatures are between 0°C and 45°C and always use the battery when temperatures are between -20°C and 60°C.
- Do not charge, use or store the battery near any ignition sources, such as fire or heaters.
- Do not use the battery if it gives off an odor, generates heat, becomes discolored or deformed, or appears abnormal in any ways. If the battery is being used or charged, remove the battery from the device or the charger immediately, and stop using it.
- Always follow the local waste and recycle laws when you get rid of the used battery.
Troubleshooting
Camera is Not Powering On
If your camera is not powering on, please try
the following solutions:
- Make sure the power switch is turned on.
- Charge the battery with a DC 5V/2A power adapter. When the green light is on, the battery is fully charged
If these won’t work, contact Reolink Support.
Failed to Scan QR Code on the Phone
If you cannot scan the QR code on your phone, please try the following
solutions:
- Remove the protective film from the camera lens.
- Wipe the camera lens with a dry paper/ towel/tissue.
- Vary the distance between your camera and the mobile phone so that the camera can focus better.
- Try to scan the QR code under sufficient lighting.
If these won’t work, contact Reolink Support.
Failed to Connect to WiFi During
Initial Setup Process
If the camera fails to connect to WiFi, please try the following solutions:
- Ensure that you have entered the correct WiFi password.
- Put the camera closer to your router to ensure a strong WiFi signal.
- Change the encryption method of the WiFi network to WPA2-PSK/WPA-PSK (safer encryption) on your router interface.
- Change your WiFi SSID or password and make sure that SSID is within 31 characters and password is within 64 characters.
If these won’t work, contact Reolink Support.
Specification
Operating Temperature:
-10°C to 55°C (14°F to 131°F)
Size: 98 x 112 mm
Weight (Battery included): 481g
For more specifications, visit the Reolink official website.
Notification of Compliance
CE Declaration of Conformity
Reolink declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU and
Directive 2014/30/EU.
UKCA Declaration of Conformity
Reolink declares that this product is in compliance with Radio Equipment
Regulations 2017 and Electromagnetic Compatibility Regulations 2016.
FCC Compliance Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
ISED Compliance Statements
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
ISED Radiation Exposure statement This equipment complies with IC RSS-102
radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20 cm between
the radiator and your body.
NOTE : Operation of 5150-5250 MHz is restricted to indoor use only in
Canada.
Correct Disposal of This Product
This marking indicates that this product should not be disposed with other household wastes.throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where theproduct was purchased. They can take this product for environmentally safe recycling.
Limited Warranty
This product comes with a 2-year limited warranty that is valid only if
purchased from Reolink Official Store or a Reolink authorized reseller.
Terms and Privacy
Use of the product is subject to your agreement to the Terms of Service and
Privacy Policy at reolink.com. Keep out of reach of children.
WiFi Operating Frequency
OPERATING FREQUENCY :
(the maximum transmitted power)
2.4GHz: (For 2.4GHz camera only):
2412MHz — 2472MHz ( EIRP < 20 dBm ) 5GHz:
5150MHz — 5250MHz ( EIRP < 23 dBm )
5745MHz — 5825MHz ( EIRP < 14 dBm )
The functions of Wireless Access Systems including Radio Local Area Networks(WAS/RLANs) within the band 5150-5350 MHz for this device are restricted to indoor use only within all European Union countries (BE/BG/CZ/DK/DE/EE/IE/EL/ES/ FR/HR/ IT/CY/LV/LT/LU/HU/MT/NL/AT/ PL/PT/RO/SI/SK/FI/SE/TR/N O/CH/IS/LI/ UK(NI)
REOLINK INNOVATION LIMITED
FLAT/RM 705 7/F FA YUEN COMMERCIAL BUILDING 75-77 FA YUEN
STREET MONG KOK KL HONG KONG
Product Ident GmbH
EU REP
Hoferstasse 9B, 71636 Ludwigsburg, Germany
Email:prodsg@libelleconsulting.com
UK REP
APEX CE SPECIALISTS LIMITED
Addr.: 89 Princess Street, Manchester, M14HT, UK
Email:info@apex-ce.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>